Allied Telesis AT-ANC10S/2+SP10SR-001 Handleiding

Allied Telesis Netwerkkaart/adapter AT-ANC10S/2+SP10SR-001

Lees hieronder de 📖 handleiding in het Nederlandse voor Allied Telesis AT-ANC10S/2+SP10SR-001 (124 pagina's) in de categorie Netwerkkaart/adapter. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/124

613-002022 Rev. B

AT-ANC10S/2

10 Gigbit Network Interface Card

Installation and User’s Guide

Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names,

logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.

Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior

written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for

any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related

to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the

possibility of such damages.

Electrical Safety and Emissions Standards

This product meets the following standards.

Federal Communications Commission Interference Statement

Declaration of Conformity

Manufacturer Name: Allied Telesis, Inc.

Declares that the product: NetExtreme II Family Adapter

Model Numbers: AT-ANC10S/2

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device must not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate this equipment.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must

follow the specific operating instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IEEE802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.

Industry Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

European Union Restriction of the Use of Certain Hazardous Substances

(RoHS) in Electrical and Electronic Equipment

This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of the Use of Certain Hazardous

Substances (RoHS) in Electrical and Electronic Equipment. Allied Telesis ensures RoHS conformance by requiring

supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls.

Product specificaties

Merk:	Allied Telesis
Categorie:	Netwerkkaart/adapter
Model:	AT-ANC10S/2+SP10SR-001
Gewicht:	78 g
Breedte:	160 mm
Hoogte:	68.9 mm
Onbalanscontrolesysteem:	Ja
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Bedraad
Certificering:	UL, FCC/EN55022 Class B, TUV, EN55024, CE, C-TICK, VCCI
Interface:	Fiber
Duurzaamheidscertificaten:	RoHS
Netwerkstandaard:	IEEE 802.1Q, IEEE 802.1Qau, IEEE 802.1Qaz, IEEE 802.1Qbb, IEEE 802.1p, IEEE 802.2, IEEE 802.3, IEEE 802.3ad
Temperatuur bij opslag:	-25 - 70 °C
Intern:	Ja
Ondersteunt Linux:	Ja
Spanning:	3.3-12 V
Hostinterface:	PCI Express
Maximale overdrachtssnelheid van gegevens:	10000 Mbit/s
Datastroombeheer:	Ja
Ondersteunde server operating systems:	Windows Server 2008, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2
Montagebeugels meegeleverd:	Ja
Jumbo Frames ondersteuning:	Ja
Component voor:	Server
Auto-negotiation:	Ja
Wifi:	Nee
Stroomverbruik (typisch):	6 W
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 90 procent
Jumbo frames:	9000
Vezel-optische connector:	LC
Fibre channel-poorten:	2
PCI versie:	2.0