Alesis M1Active 520 USB Handleiding

Alesis Speaker M1Active 520 USB

Lees hieronder de 📖 handleiding in het Nederlandse voor Alesis M1Active 520 USB (12 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

M1ACTIVE 520 USB

STUDIO MONITORS WITH USB AUDIO INTERFACE

QUICKSTART GUIDE

(ENGLISH) 1 – 2

GUÍA DE INICIO RÁPIDO

(ESPAÑOL) 3 – 4

GUIDE D’UTILISATION SIMPLIFIÉ

(FRANÇAIS) 5 – 6

GUIDA RAPIDA

(ITALIANO) 7 – 8

KURZANLEITUNG

(DEUTSCH) 9 – 10

vo lume

p itch

x y

octave

accomp

store

tap

phrase

latch

ana l o g m o d e l in g s y n t h

ana l o

ana l o g m o d

g m o d

g m o d eli n g

eli n g

eli n g sy n t

sy n t

sy n t h

push

HOOKUP DIAGRAM

READ THE SAFETY & WARRANTY INFORMATION

BEFORE USING THIS PRODUCT!

Refer to the possible connection scenario for hooking up

the M1 Active 520 USB speakers.

AUDIO SETUP WITH YOUR COMPUTER

The M1Active 520 USB speakers are plug-and-play, so there is no

special driver installation necessary. Simply power on the speakers,

connect them to your computer’s USB port and all the necessary

drivers will be automatically installed. To enable your M1Active 520

USB speakers to send and receive audio to and from your computer,

follow the instructions below for your computer's operating system:

WINDOWS VISTA:

1. Go to Start Menu 



 Control Panel 



 Sound. (If you don’t see

Sound, select Switch to Classic View, and the Sound Control

Panel should become available.)

2. Click the Playback tab and select USB Audio Codec* as the

default device. (To enable recording through the M1Active 520

USB's 1/4" TRS INPUTS, click the Recording tab and select USB

Audio Codec* as the default device.**)

3. Click OK.

WINDOWS XP:

1. Go to Start Menu 



 Control Panel 



 Sounds and Audio Devices.

2. Click the Audio tab.

3. Under Sound Playback, select USB Audio Codec* as the default device. (To enable recording through the M1Active

520 USB's 1/4" TRS INPUTS, select USB Audio Codec* as the default Sound Recording device.**)

4. Click OK.

MAC:

1. Go to Applications 



 Utilities 



 Audio MIDI Setup.

2. In the Audio Devices tab under System Settings, select USB Audio Codec* as your Default Output. (To enable

recording through the M1Active 520 USB's 1/4" TRS INPUTS, select USB Audio Codec* as your Default Input.**)

3. Close the window.

BOX CONTENTS

y M1Active 520 USB Speakers

y Power Cable

y USB Cable

y XLR Cable

y Quickstart Guide

y Safety & Warranty Information

* If you have other USB audio devices

connected to your computer, which may

have identical names, you may need to try

selecting each one until the M1Active 520

USB speakers are recognized.

COMPUTER

KEYBOARD OR

SOUND MODULE

POWER SOURCE

XLR CABLE

(INCLUDED)

** If you wish to record audio through the

M1Active 520 USB speakers, be sure your

audio software program is set up to receive

audio from them. This can usually be done

in your software’s "Preferences" or "Device

Setup." Please consult your software

manual for more information.

If you experience problems when connecting

the speakers through a USB hub, we

recommend connecting the speakers directly

our com

uter.

ABOUT LATENCY & THIRD-PARTY ASIO DRIVERS

"Latency" is the delay between the moment when audio is generated and the moment when you actually hear it. Higher

latency means a longer delay.

The M1Active 520 USB speakers feature zero latency direct monitoring so you don’t have to worry about latency when

monitoring input sources connected to the rear of the speakers. However, latency may become an issue when using software

synths and instruments.

Generally, you want to keep latency as low as possible while still allowing your equipment to operate without glitches.

Latency and buffering is usually adjusted in your software’s Preferences settings.

If you still experience too much latency or "lag" when using software synths and instruments, you might want to download

one of the free and widely available ASIO (Audio Stream Input/Output) drivers from the Internet. In general, ASIO drivers

may perform better and with lower latency since they create a more efficient communication between audio devices and

software. You may download and install the free ASIO4ALL driver (PC) by visiting www.asio4all.com.

FRONT PANEL OVERVIEW

1. VOL/POWER – This knob is used to turn the speakers on and adjust their volume.

To turn on, simply turn up the knob; you will feel a click when the speakers turn on.

2. HEADPHONES – Connect your 1/4" headphones to this output to hear the mix

through your headphones. Note that while the headphones are connected, you will

not be able to hear sound out of your speakers until the headphones are

disconnected.

3. POWER / CLIP INDICATOR – This light will illuminate blue when it detects incoming

audio signal. It will illuminate red if that signal is clipping.

REAR PANEL OVERVIEW

1. POWER – Use the

included power cable

to connect the

speakers to a live

power source. Make

sure your AC

VOLTAGE

SELECTOR is set to

the correct voltage for

your country.

2. AC VOLTAGE

SELECTOR – This 2-

position switch sets

the AC input voltage

for the speaker. US

users should set this

switch to "100-120V"

whereas UK and most

European users will

need to set this to

"220-240V."

3. USB (1.1) – Use the

supplied USB cable to

connect the speaker

system to your

computer. Note that the M1Active 520 USB speakers are Plug-

and-Play so there is no additional driver installation necessary;

the speakers should be ready to use as soon as they are

plugged in.

4. OUTPUT TO LEFT SPEAKER – This is the audio connection to

the left speaker. Use the included XLR cable to connect the right speaker to the left speaker.

5. 1/4” TRS INPUTS – Use 1/4" TRS cables (not included) to connect external sound sources to these inputs.

6. BASS BOOST – This 2-position switch allows you to boost the speakers’ bass frequencies.

12 3

Product specificaties

Merk:	Alesis
Categorie:	Speaker
Model:	M1Active 520 USB
Kleur van het product:	Zwart
Breedte:	184 mm
Diepte:	225.5 mm
Hoogte:	269.9 mm
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	30 W
Equalizer-instellingen:	Nee
Aanbevolen gebruik:	Universeel
Impedantie:	- Ohm
3,5mm-connector:	Ja
Geschikt voor buitengebruik:	Nee
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Floor, Tabletop/bookshelf
Aantal drivers:	1
Diameter driver subwoofer (imperiaal):	5 "
Frequentiebereik:	56 - 20000 Hz
Gevoeligheid:	90 dB
Tweeter:	Ja
Versterker input impedantie:	10000 Ohm