Air King MQFAM Handleiding

Air King Niet gecategoriseerd MQFAM

Lees hieronder de 📖 handleiding in het Nederlandse voor Air King MQFAM (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 230 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

www.airkinglimited.com6728092 Rev. E 4/22 1 of 12

SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK AND INJURY TO PERSON,

OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service panel

and lock the service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to

the service panel.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK AND INJURY TO PERSON,

OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualified person(s)

in accordance with all applicable codes and standards, including fire-

related construction.

b) Sufficient air is needed for proper combustion and exhausting of gases

through the flue (chimney) of fuel burning equipment to prevent back

drafting. Follow the heating equipment manufacturer’s guideline and

safety standards such as those published by the National Fire Protection

Association (NFPA) and the American Society for Heating, Refrigeration,

and Air Conditioning Engineers (ASHRAE), and the local code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

CAUTION: FOR GENERAL VENTILATING USE ONLY.

DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE

MATERIALS AND VAPORS.

d) This unit must be grounded.

e) To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

f) Read all instructions before installing or using exhaust fan.

g) For residential installations only.

h) Must use suitable weather hood with insect screen to protect air intake.

WARNING: TO REDUCE THE RISK OF FIRE,

REMOVE ANY SHIPPING MATERIAL THAT MAY BE

PRESENT INSIDE THE UNIT.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY

SOLID-STATE SPEED CONTROL DEVICE.

WARNING: DO NOT USE IN KITCHENS.

WARNING: THE DUCTING FROM THIS FAN TO THE

OUTSIDE OF THE BUILDING HAS A STRONG EFFECT ON THE

AIR FLOW, NOISE AND ENERGY USE OF THE FAN. USE THE SHORTEST,

STRAIGHTEST DUCT ROUTING POSSIBLE FOR BEST PERFORMANCE,

AND AVOID INSTALLING THE FAN WITH SMALLER DUCTS THAN

RECOMMENDED. INSULATION AROUND THE DUCTS CAN REDUCE

ENERGY LOSS AND INHIBIT MOLD GROWTH. FANS INSTALLED WITH

EXISTING DUCTS MAY NOT ACHIEVE THEIR RATED AIRFLOW.

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN

THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL

INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should

always be followed to reduce the risk of fire, electric shock and

injury to person, including the following:

Inline Fan

MQFAM, MFAS

IMPORTANT INSTRUCTIONS - OPERATING MANUAL

www.airkinglimited.com6728092 Rev. E 4/22 2 of 12

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

WARNING: TO REDUCE THE RISK OF FIRE, REMOVE ANY

SHIPPING MATERIAL THAT MAY BE PRESENT INSIDE THE UNIT.

SECTION 1

Preparing the Fan

1. Unpack fan from the carton and confirm that all pieces are present. In addition to the fan

you should have:

2 - Collar Assembly (attached) 1 - Controller (attached) (MQFAM only)

2 - Mounting Brackets (attached) 1 - Instruction/Safety Sheet

2. Choose the location for your fan. To ensure the best air and sound performance, it is

recommended that the length of ducting and the number of elbows be kept to a minimum,

the radius of each elbow be as large as possible for the installation, and that insulated hard

ducting be used. This fan will require at least 10" of clearance in the ceiling or wall. The

fan mounts using the provided mounting brackets or can be surface mounted to a wall or

ceiling.

NOTE: The fan must be installed into a location that can be easily accessed once installed.

3. No additional vibration deadening materials are needed for this fan.

SECTION 2

Mounting the Fan

1. Confirm the fan is positioned so the air flow is in the correct direction.

2a. Surface Mounting: Locate at least one stud or joist. Place the fan in position so that the

mounting bracket is centered on the stud or joist and make the location for the four (4)

holes. Remove the fan and install properly rated wall/ceiling anchors for the holes that do

not go directly into a joist or stud. Position fan in place and secure with screws (not

included) (Figure 1).

2b. Mounting to a Joist: Install two - 2 x 4 headers (not included) between the joists. Position

the fan housing on top of the headers and secure the mounting brackets with screws (not

included) to the header .(Figure 2)

2c. Hanging Bar Mounting: Lift unit up onto the threaded rods and secure in place using

appropriate hardware (not included) (Figure 3).

Figure 1

Screws

Stud/Joist Anchor

Air Flow

Figure 2

Joist

2 x 4 Header

Bracket

Figure 3 Bracket

Housing

Threaded Rod

SECTION 3

Ducting

NOTE: 6" OR LARGER RIGID DUCT IS RECOMMENDED FOR BEST PERFORMANCE.

CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL

BUILDING CODES.

NOTE: The ducting from this fan to the outside of the building has a strong effect on the air

flow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for

best performance, and avoid installing the fan with smaller ducts than recommended. Insulation

around the ducts can reduce energy loss and inhibit mold growth. Fans installed with existing

ducts may not achieve their rated air flow.

WARNING: MAKE SURE THE FRESH AIR INTAKE PORT COMPLIES WITH

ALL LOCAL AND NATIONAL CODES AND IS LOCATED AT LEAST 6 FEET AWAY

FROM SOURCES OF CONTAMINATION SUCH AS BUT NOT LIMITED TO: DRYER,

FURNACE OR CENTRAL VACUUM EXHAUSTS, GAS APPLIANCES SUCH AS BBQ GRILLS,

GARBAGE BINS OR OTHER EXHAUST PORTS.

NOTE: To ensure quiet operation of in-line and remote fans, each fan shall be installed using

sound attenuation techniques appropriate for the installation. For bathroom and general

ventilation applications, at least 8 feet of insulated flexible duct shall be installed between the

exhaust or supply grille(s) and the fan.

1. Connect the ducting to the fan’s duct collar Seal ducting to housing with (Figure 4).

appropriately rated tape. Use screws or suitable clamps to secure in place. Make sure the

fresh air intake is connected to a properly installed intake port that is a suitable weather

hood with insect screen to protect air intake. It is recommended that low restriction

termination fittings be used.

2. Ensure duct joints and exterior penetrations are sealed with caulk or other similar material

to create an air-tight path to minimize building heat loss or gain and to reduce the potential

for condensation. Place/wrap insulation around duct and/or fan in order to minimize

possible condensation buildup within the duct, as well as building heat loss or gain.

NOTE: At the base of the duct adapter, there is a small diameter test port hole covered with a

plastic cap. Make sure the test port is not covered up with the ducting so that it can be accessed

for pitot tube testing. To access the port, remove the port cover and insert tube.

SECTION 4

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE

IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL

ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL

WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

NOTE: This unit includes a side access panel for wiring that does not require the removal of the

fan’s blower assembly.

1. Remove the wire compartment cover screw and place cover in a secure place (Figure 5).

Figure 4

Air Flow

Intake

Ducting

Outlet

Ducting

Test Port

Figure 5

Screw

Wire

Compartment

Cover

Ground

Screw

www.airkinglimited.com6728092 Rev. E 4/22 3 of 12

2. Pull the loose black, white and green wires out from the wire compartment (additional

wires will be present). Install an approved electrical connector to the wire compartment

cover (not included). Run a black (hot), white (neutral), and a green or bare ground wire

from the supply through the electrical connector. Connect all wires from the supply to their

corresponding wires within the wire compartment . Use approved methods for (Figure 6)

all connections.

3. Carefully tuck wires back inside wire compartment and replace wire compartment cover

securing with the screw that was removed earlier.

SECTION 5

Setting the Speed

1. Determine the CFM required. The unit can

be set for 50 CFM or 80 CFM. Remove the

screw securing the access panel cover in

place and open the cover to gain access.

Locate the speed control panel inside the

unit (Figure 7).

2. Locate the rocker switch at the top of the

wiring compartment and set to the desired

CFM - “Low” for 50 CFM or “HIGH” for 80

CFM (Figure 8).

SECTION 6

Optional Air Filter

An air filter (available separately) can be added

to this unit to provide additional filtration of the

intake air. The unit will accept a 9" x 8" x 2" filter.

To install:

NOTE: Adding an air filter will decrease the

airflow of the unit. Filters must be changed

regularly. Refer to the filter manufacturer’s

recommendations to determine how often the

filter should be changed.

1. Remove the screw securing the access panel cover in place and open the cover to gain

access to the controls and filter area.

2. Ensure the filter is facing the correct way and slide the filter into the slot in the housing.

Make sure the filter is seated all the way to the bottom of the housing (Figure 9).

3. Close the access panel and reinstall the screw holding the access panel in place.

SECTION 7

Completing the Installation

NOTE: When fan is mounted inline and no penetration is made into unconditioned spaces, there

is no need to use a sealant appropriate for contact with the building materials present and for the

temperature requirements of the installation to prevent air leakage from unconditioned spaces.

Additional material (backing rod, ceiling material) are also not required.

Figure 6

Supply from house

Black

Neutral (White)

Ground (Green or Bare)

Fan

Neutral (White)

Green

Black

Green

By others

Screw

Figure 7

Rocker

Switch

50 80

Figure 8

Figure 9

Filter

Screw

Air Flow

NOTE: This unit is equipped with a wire mesh insect screen. Confirm that the screen is installed

on the inside of the unit on the inlet ducting side.

1. If the screen is not in place, insert the screen into the tab at the base of the unit (make sure

the wider side of the screen is running side to side inside the unit) (Figure 10).

2. Slide the screen to the side with the larger top tab making sure the screen fits behind the

tab (Figure 10).

3. Slide the screen back over towards the smaller top tab making sure the screen fits behind

the tab (Figure 11).

4. Confirm that the screen is being held in place by both top tabs (Figure 11).

5. Close the access panel and reinstall the screw holding the access panel in place.

6. Restore power and test your installation.

SECTION 8 (MQFAM Only)

Using the Controller

1. On Mode: Fan will run continuously when the ON button ( ) is pressed. If ambient

temperature is lower than 34°F (2°C), the fan will stop and initiate Sampling Mode. Sampling

Mode Cycle: stop 15 mins; run for 5 minutes to determine current air temperature. During

Sampling Cycle, if the temperature is in the accessory heater (optional) control range, the

heater will turn on (if it has been installed). The fan will return to continuous ventilation

once ambient temperature rises above 34°F (2°C).

2. Energy Savings Mode: To enter the Energy Savings mode, press the Energy Savings

button ( ) until appears on the left side of the display. Energy Savings mode

engages the settings configured in . When the unit is on, the display will SECTION 9

show the current conditions (temperature and humidity level) as well as if it is in Energy

Savings mode or not. Other icons/information that may be on the display include:

Fan icon appears when the fan is on.

“HI°F” appears if the intake temperature is above 150°F (65°C).

“Lo°F” appears if the intake temperature is below 15°F (-10°C).

“Lo%” appears if the intake humidity is below 10%.

3. Optional Heater Unit: An optional heater unit is available for climates that the air coming into

the unit falls below 54°F (12°C). To install the unit, follow the directions that are included with

that unit. The display will show a thermometer icon with either a “1”( 1) or “1 2” ( 1

2) when

the temperature range is at a level where the heating element would come on if present.

Stage 1 - “1” turns on when the intake air temperature is between 39°F (4°C) and 54°F

(12°C). Stages 1 and 2 “1 2” turn on when the intake air temperature is between 33°F (0°C)

and 39°F (4°C).

Figure 10

Base Tab

Screen

Larger

Top Tab

Figure 11

Screen

Smaller Top Tab

Screen

Product specificaties

Merk:	Air King
Categorie:	Niet gecategoriseerd
Model:	MQFAM

Heb je hulp nodig?

Als je hulp nodig hebt met Air King MQFAM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Air King

Air King F130D Handleiding

13 Juni 2023

Air King LEDAK100D Handleiding

23 Mei 2023

Air King QMDB Handleiding

13 Mei 2023

Air King EVLDGH Handleiding

10 Mei 2023

Air King DL4D Handleiding

23 April 2023

Air King MD624 Handleiding

20 April 2023

Air King R120 Handleiding

20 April 2023

Air King EVLD Handleiding

12 April 2023

Air King D4S Handleiding

10 April 2023

Air King BFQ70W Handleiding

9 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024

Kolcraft MLB New York Yankees Handleiding

26 November 2024

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024

Nedis POCO106 Handleiding

26 November 2024

Nedis BTSM1GY Handleiding

26 November 2024

Turbosound TPOLEAJ-01 Handleiding

26 November 2024

Turbosound TSTAND-01 Handleiding

26 November 2024

IFM TAD981 Handleiding

26 November 2024

IFM TAD961 Handleiding

26 November 2024