AFX Shaw SHAL054840LAJMV Handleiding

AFX Verlichting Shaw SHAL054840LAJMV

Lees hieronder de 📖 handleiding in het Nederlandse voor AFX Shaw SHAL054840LAJMV (1 pagina's) in de categorie Verlichting. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

LED door Luminaires In

Ceiling Mount

120 277- VAC 60Hz/

Page 1 of 1 R0 8061530

Model #: SHAL052220LAJMV

SHAL054840LAJMV

Limited Factory Warranty

AFX Inc. hereby warrants that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years

from date of purchase. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due to improper

installation, misuse, mishandling or damage incurred in transit.

View shown for reference

only. Individual models

may vary.

Safety Precautions

 Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal electric shock and/or

property damage.

 is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes. It

 Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.

 This xture is designed for use in a 120- VAC / 60Hz circuit. This xture is not compatible on dimming circuit. 277

 Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).

 To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground wire (green)

contact between this xture and the ground connection of your main power supply panel.

 This xture is intended to be used for general indoor lighting in dry or damp locations.

 Disclaimer

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and

found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005 (B). These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiver antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult with the dealer or an experienced radio/TV technician for help.

Any modications to this xture may void the warranty and interfere with the safe operation of the luminaire.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Assembly Instructions

Step 1 Preparing for installation–

A. at fuse or circuit breaker box before installing or servicing any part of Disconnect electrical power

this xture.

B. Carefully remove the xture from the carton, remove components from hardware kit.

C. Remove diuser (5) from xture (1) by gently pull away then set it aside until ready to be

reinstalled.

D. Position the xture (1) onto the ceiling aligning with junction box (not included) use pencil to and

mark four mounting locations for drywall anchors. Take the xture (1) down and punch a small hole

in the ceiling at each of the locations using a nail to see if there is a wood stud to mount the xture

to. Where there is a wood stud, use a suitable screw (3) to mount the xture. Where there is no

stud to screw into, a drywall anchor or toggle bolt (4) must be used to mount the xture securely to

the ceiling.

E. Pull the power supply wires down into the xture. through an Ø1/2” hole

F. Install the xture to the ceiling using four wood screws (3) and two screws (2) to secure it.

Wiring All wiring must take place inside junction box (not included) –

Caution: Make sure power is o at fuse or circuit breaker box. Check power wires for damage or

scrapes. If power supply wires are within three inches of the LED driver, use wire suitable for at

least 90°C (194°F). Most dwellings built before 1985 have supply wire rated to 60°C. Consult Note:

a qualied electrician to ensure correct branch circuit conductor before installing.

Step 2 Wiring xture –

A. Make all wire connections to appropriate wire. Secure with wire nuts (provided).

B. Connect the green wire from the xture to the supply power source ground wire.

C. Connect the white wire from the xture to the white (N) wire from supply power source.

D. Connect the black xture wire to the black (L) wire from supply power sourc e.

E. Pull on each wire lead to make sure connections are secure. Make certain no Do not mix wires.

bare wires are exposed outside of wire connectors. Tuck all connections neatly into the junction

box.

Step 3 Color changing temperature adjustment, CCT (if desired) –

A. Adjust CCT switch on the board according to the desired color temperature as shown below. Note:

Fixture is preset to 3000K from factory.

Step 4 Install Diffuser –

A. Insert diuser (5) groove to long edge of the xture (1) one side rst then gently push the other side with thumb until

diuser groove is captivated and ush with the xture to secure it.

Step 5 Restore power at fuse or circuit breaker box –

Product specificaties

Merk:	AFX
Categorie:	Verlichting
Model:	Shaw SHAL054840LAJMV

Heb je hulp nodig?

Als je hulp nodig hebt met AFX Shaw SHAL054840LAJMV stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Verlichting AFX

AFX Grace GRCP07CBBK Handleiding

12 Oktober 2024

AFX Point PNTP0107L30D1BK Handleiding

12 Oktober 2024

AFX Marquette MQTB3840L30ENWN Handleiding

25 September 2024

AFX Reeves RVEF1624LAJUDSNLW Handleiding

25 September 2024

AFX Arlo ARLS050407L35MVSN Handleiding

25 September 2024

AFX Grace GRCC14CBBK Handleiding

25 September 2024

AFX Plaza PLZS11MBBN Handleiding

25 September 2024

AFX Shaw SHAL054840LAJMV Handleiding

25 September 2024

AFX Ryland RYDV280422L30D2SN Handleiding

25 September 2024

AFX Novara NVS5131200L30D1SN Handleiding

25 September 2024

Handleiding Verlichting

Nieuwste handleidingen voor Verlichting

LumenRadio CRMX Galileo MAX Handleiding

21 December 2024

Showtec Performer Fresnel 2200 DDT Handleiding

21 December 2024

Showtec AirDrive 2.4 IP Handleiding

21 December 2024

Bosch FSN 1400 Set Professional Handleiding

21 December 2024

Neewer VL66C Handleiding

18 December 2024

American DJ ENCORE LB15IP Handleiding

18 December 2024

American DJ ENCORE LP12IP Handleiding

18 December 2024

Wiesenfield UNI-LP-100 Handleiding

17 December 2024

Cateye Wearable mini SL-WA10 Handleiding

16 December 2024

Cateye Volt50 HL-EL460RC-REAR Handleiding

16 December 2024