AFX Reeves RVEF2032LAJUDSNLW Handleiding

AFX Verlichting Reeves RVEF2032LAJUDSNLW

Lees hieronder de 📖 handleiding in het Nederlandse voor AFX Reeves RVEF2032LAJUDSNLW (2 pagina's) in de categorie Verlichting. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

LED Indoor Luminaires

Reeves Flush Mount

120-277VAC / 60Hz

Page 1 of 1 8061271 R0

Part # RVEF1624LAJUDSNLW

RVEF2032LAJUDSNLW

Safety Precautions

 Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal

electric shock and/or property d amage.

 It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.

 Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.

 This xture is designed for use in a 120-277VAC, 60Hz fused circuit. The xture is compatible with Triac (forward-phase or leading edge) / ELV (reverse phase or trailing edge) and

0-10 V dimmers. Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).

 To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground

wire (green) contact between this xture and the ground connection of your main power supply panel.

 This xture is intended to be used for general indoor lighting in dry or damp locations.

 Disclaimer

Changes or modications : This equipment has been not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE

tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES- -005 (B) / NMB 005 (B). These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiver antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult with the dealer or an experienced radio/TV technician for help.

Any modications to this xture may void the warranty and interfere with the safe operation of the luminai re.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Assembly Instructions

1. Preparing for installation.

A. Disconnect electrical power before installing or servicing any part of this xture.

B. Remove xture from carton; remove components from hardware kit.

2. Wiring. All wiring must take place inside junction box.

Caution: Make sure power is o at fuse or circuit breaker box. Check power wires for damage or scrapes.

If the power supply wires are within three inches of the driver, use a wire suitable for at least 90C (194F).

Note: Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualied electrician before

installing.

A. electrical circuit. Electrical shock, This unit will not operate properly unless connected to a “grounded”

overheating, low or no light output, and shortened LED life can result if proper grounding is not done.

Securely attach power source ground wire and xture ground wire to green ground screw on circular

mounting bracke t.

B. Make all wire connections to appropriate wire. Secure with wire nuts (provided).

C. . Fixture will operate normally w/o connection to any dimmers. Connect For none-dimming xture

white xture lead to white (N) wire from supply power source. Connect black xture lead to black (L)

wire from supply power source. Gray and purple wires are not to be used and must be individually

capped to prevent shorting.

D. Connect white xture lead to (N) wire from dimming source per dimmer wiring For TRIAC dimming.

instructions. Connect black xture lead to black (L) wire from dimmer supply power source. Gray and

purple wires are not to be used and must be individually capped to prevent shorting.

E. . Connect gray wire from the xture to the dimmer source gray wire. Connect purple wire from the xture to the dimmer source purple For (0-10V) dimming xture

wire. Connect white xture lead to white (N) wire from supply power source. Connect black xture lead to black (L) wire fro dimmer supply power source. m

F. . Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire connectors. Tuck all Do not mix wires

connections neatly into junction box.

3. Back pan mounting.

A. Install ceiling pan ) to junction box (NOT INCLUDED) with two screws (2). (1

4. Color Changing Temperature Adjustment, CCT (if desired).

A. Adjust the two switches on each board accordingly to the desired color temperature as seen below. All boards must be set the same way. Fixture is preset to Note:

3500K from factory.

5. Mounting diuser.

A. Slide diuser (3) in from the top opening between the shade and mounting pan in the xture assembly (1).

B. Gently set it into place centered in the shade opening.

6. Power to the xture can now be restored.

Limited Factory Warranty

AFX Inc. hereby warranty that this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years

from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due

to improper installation, misuse, mishandling or damage incurred in transit.