Advantech MOS-1130Y-0201E Handleiding

Advantech Niet gecategoriseerd MOS-1130Y-0201E

Lees hieronder de 📖 handleiding in het Nederlandse voor Advantech MOS-1130Y-0201E (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/5
MOS-1130 User Manual 1
1. Packing List
2. Initial Inspection
MOS-1130Y-0201E Isolated CANBus iDoor Module
User Manual
MOS-1130Y- a 2-Ports Isolated CANBus mini- PCIe, DB9. 0201E is
This manual covers the assignment for the CAN connector,and the wiring the two transmission wires. pin of
MOS- 1130
miniPCIe Card x 1
DB37 I/O Plate x 2 with iDoor bracket x 1
FPC cable x 2
Startup Manual x 1
Note: If any of these items are missing damaged, please contact your distributor sales representative immediately. or or
You should nd the following items inside the shipping package:
Mini-PCIe communication interface card
Industrial Communication Driver, Utility and mini-PCIe communication card user's manual in DVD-ROM
MOS- was carefully inspected mechanically 1130 and electrically before was shipped. it It should be free of marks and
scratches and in perfect working order when received.
As you unpack the MOS Module, check for signs of shipping damage (damaged box, scratches, dents, etc.). If it is
damaged or it fails to meet specications, notify our service department or your local sales representative immediately. Also
notify the carrier. Retain the shipping carton and packing material for inspection the carrier. by
After inspection will make arrangements we to repair replace the unit. When you handle the MOS Module, remove or
it from its protective packaging by grasping the rear metal panel. Keep the anti-vibration packing. Whenever you remove
the card from the PC, store in this package for protection. it
Warning!
Discharge your body’s static electric charge by touching the back of the grounded chassis of the system unit
(metal) before handling the board. You should avoid contact with materials that hold a static charge such as
plastic, vinyl and Styrofoam. Handle the board only by its edges to avoid static damage to its integrated circuits.
Avoid touching the exposed circuit connectors. We also recommend that you use a grounded wrist strap and place
the card on a static dissipative mat whenever you work with it.
MOS-1130 User Manual 2
Please follow the steps below install Advantech CAN WDM Driver. to
For driver download, please visit Advantech website:
http://support.advantech.com/Support/SearchResult.aspx?keyword=MOS-1130Y-0201E&searchtabs=BIOS,Certicate,Dat
asheet,Driver,Firmware,Manual,Online%20Training,Software%20Utility,Utility,FAQ,Installation,Software%20API,Software
%20API%20Manual,3D%20Model&select_tab=Driver
1. Select “Next” to continue the installation.
2. After a while, the installation will complete. be
3. After the physical hardware has been installed, the card will automatically detected. be
Advantech provides WDM CAN driver that allows you congure your hardware and store the settings in your Windows to
registry. You must install the WDM CAN driver if you want and manage Advantech CAN cards. to add
3. Driver Advantech Device Managerand
MOS-1130 User Manual 3
4.1
How Set Jumpersto
Figure 1 CAN- transceiver board silk screen bus
You congure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of
electric switch. consists of two metal pins and a small metal clip (often protected a plastic cover) that slides over It by
the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the
clip.
Figure 2 How to set the jumpers
4.2
Terminator Resistor Setup (JP1)
You can set the terminator resistor necessary match impedance. Each port if to has a separate resistor located its on
own transceiver board.
Note!
Table MOS-1130 Terminator Resistor Jumper Setting 1:
is suggested set the terminator resistor 120 Ohm to to to maintain a satisfactory baud rate performance.
4. Jumper and Switch Settings
Status
Value Terminator Resistor (Ohm) of
Pin 2-3
Open mode
None
Pin 1-2
Close mode
120 Ohms

Product specificaties

Merk: Advantech
Categorie: Niet gecategoriseerd
Model: MOS-1130Y-0201E

Heb je hulp nodig?

Als je hulp nodig hebt met Advantech MOS-1130Y-0201E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Advantech

Advantech

Advantech MIO-2363AW-P1A1 Handleiding

14 December 2024
Advantech

Advantech UNO-247-1 Handleiding

7 December 2024
Advantech

Advantech USB-4604BM-BE Handleiding

7 December 2024
Advantech

Advantech UNO-247-J121W10 Handleiding

7 December 2024
Advantech

Advantech EKI-2741SX-BE Handleiding

7 December 2024
Advantech

Advantech MIO-2375C3P-P9A1 Handleiding

7 December 2024
Advantech

Advantech MIO-2361N-S2A2 Handleiding

7 December 2024
Advantech

Advantech UNO-2271G-E21BE Handleiding

7 December 2024
Advantech

Advantech EKI-2741LXI-BE Handleiding

7 December 2024
Advantech

Advantech HPC-8108 Handleiding

19 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx

Gourmetmaxx 03863 Handleiding

24 December 2024
Vello

Vello PGS-P Handleiding

24 December 2024
Venom

Venom Quad Charging Station VS4796 Handleiding

24 December 2024
Nec

Nec IPJ2000CM Handleiding

24 December 2024
Monogram

Monogram ZKPN Handleiding

24 December 2024
Philips

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024
Philips

Philips Senseo HD7002 Handleiding

24 December 2024
D-Link

D-Link DUB-C2 Handleiding

24 December 2024
Nec

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024
Nec

Nec DS1-TM01 Handleiding

24 December 2024