Adj HD MB40KG Handleiding

Adj Niet gecategoriseerd HD MB40KG

Lees hieronder de đź“– handleiding in het Nederlandse voor Adj HD MB40KG (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
SPECIFICATIONS:
Working Position: Upside Down
Power: 120V/60Hz
Weight: 6lbs./ 2.5Kgs.
Length: 11.25” (L) x 9.5” (W) x 4.5” (H)
280 x 240 x 110mm
Rotation Speed: 1 - 1.5 R.P.M.
Max Load: 89 lbs/40Kgs
Warranty: 1 Year (365 days)
Introduction: The HD MB40KG is a heavy-duty 1.5 R.P.M. mirror ball motor from American DJ that
will work with mirror balls up to 39 inches (1m) that weigh up to 89lbs (40 kgs.). Just plug it in and it
will start to work immediately. The HD MB40KG is easy-to-use and is intended for indoor use for night
clubs and permanent installations or in mobile applications for mobile DJs or bands.
Unpacking: Thank you for purchasing the by AHD MB40KG DJ Products, LLC. Every HD MB40KG
has been thoroughly tested and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to
be damaged, carefully inspect your xture for any damage and be sure all accessories necessary to
operate the unit has arrived intact. In the case damage has been found or parts are missing, please
contact our toll free customer support number for further instructions. Do not return this unit to your
dealer without rst contacting customer support.
In order to ensure a safe operation, it is absolutely necessary for the user to follow the safety instruc-
tions and warning notes written in this user manual.
Important: Damages caused by the disregard of this user manual are not subject to warranty. The
dealer will not accept liability for any resulting defects or problems.
SAFETY INSTRUCTIONS:
CAUTION: Be careful when operating. A dangerous voltage can give you a dangerous electric shock when
touching the wires!
• This device has left our building in an absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
• If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not it on im-
mediately. The arising condensation water might damage your device. Leave the device switched off until it
has reached room temperature.
ELECTRICAL PRECAUTIONS:
• The electric connection must only be carried out by a qualied electrician!
• Never let the power–cord come into contact with other cables! Handle the power-cord and all connections
HD MB40KG
with the mains with particular caution!
• Make sure that the available voltage is not higher than the device’s stated voltage.
• Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.
• Always disconnect the power, when the device is not in use or before cleaning it.
• Keep away children!
INSTALLATION & PRECAUTIONS:
• THE MAXIMUM WEIGHT THAT THE MIRROR BALL MOTOR CAN HOLD MUST NOT EXCEED 89LBS.
• This product was designed for indoor use only.
• Make sure that the area located below the installation is clear when rigging, derigging or servicing the x-
ture.
• Please save and use the original packaging for transportation.
• If this mirror ball motor is operated in any way different to the way described in this manual, the product
may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers
like short-circuits, burns, electric shock, crash etc.
• Please consider the EN 60598 norms during the installation!
• The installation must only be carried out by a qualied electrician or an authorized dealer!
• The installation sturcture of the mirror ball has to be built and constructed in a way that it can hold 5 times
the weight for 1 hour without any causing any deformation of the installation structure.
• The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be used in a way that no part of the installation can fall down if the
main attachment fails, e.g. a safety cable.
• Rigging/installing, derigging or servicing the xture over any high working places, general public, and other
dangerous areas is forbidden.
• The operator has to make sure that safety-relation and machine-technical installations are approved by an
expert before operating for the rst time and after any changes in installation.
• The operator should make sure that safety-relation and machine-technical installations are approved by an
expert after every four years.
• The operator should make sure that safety-relation and machine-technical installations are approved by a
skilled person once a year.
• The mirror ball should be installed outside areas where persons may walk by or be seated.
• The chosen installation spot must be in a way that the motor can be installed in an absolutely horizontal
position.
• The motor and the mirror ball must be installed out of the reach of people.
• If the motor shall be lowered from the ceiling or high joists, professional trussing systems have to be used.
The motor must never be installed in a way that it can swing freely in the room.
Caution: Mirror balls will cause severe injury if it happens to come crashing down! If you have any doubts
concerning the safety of a possible installation, do NOT install the motor!
• BEFORE RIGGING MAKE SURE THAT THE INSTALLATION STRUC-
TRUE IS ABLE TO HOLD A MINIMUM OF 400LBS. POINT LOAD.
• Please install the mirror ball motor using all 10-xation holes.
• Only use the appropriate screws and make sure that the screws are prop-
erly connected with the ground.
• If the unit will be directly connected with the local power supply network,
a disconnection switch with a minimum opening of 3 mm at every pole has
to be included in the permanent electrical installation.
• The mirror ball has to be connected via an appropriate installation with
the motor. We recommend using Chain for Mirror balls up to 50 cm certi-
ed, or Chain for Mirror ball up to 100 cm certied.
Caution: The installation material must never include abrading material e.g. steel cables in order to
avoid material wearing.
• The length of the chain must never exceed 100 cm.
Fixation Screw
MOTOR
AXLE
SCREW-ON
CHAIN LINK
A ACHMENT TT
E LETYE
HOUSING
Fixation holes
• Insert the chain with the mirror ball in the screw-on chain link and lighten the xation screw.
• Make sure that the rotation of the mirror ball is never slowed down or stopped/obstructed.
• Please check in regular intervals, if the key ring or chain links have been deformed/damaged. Remove the
mirror ball installation immediately!
CLEANING AND MAINTENANCE
• We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never
use alcohol or solvents!
• There are no serviceable parts inside the device. Maintenance and service operations are only to be carried
out by authorized dealers.
• Should you need any spare parts, please use genuine parts.
• If the power supply cable of this device becomes damaged, it has to be replaced by authorized dealers only
in order to avoid hazards.
• Should you have further questions, please contact your dealer.
Caution!
No user serviceable parts do not attempt repairs. In the event your HD MB40KG
should fail, contact ADJ Products, LLC.
Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up help
and to answer any question should you encounter problems during your set up or initial operation. You
may also visit us on the web at www.americandj.com for any comments or suggestions. Service Hours are
Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: (800) 322-6337 Fax: (323) 582-2941 E-mail: support@americandj.com
The Please HD MB40KG carries a 1 year (365 days) limited warranty. fill out the enclosed warranty card
to validate your purchase. All returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) umber. If the is under warranty you n remote
must provide a copy of your proof of purchase invoice. Please contact A customer support for a DJ
R.A. number.

Product specificaties

Merk: Adj
Categorie: Niet gecategoriseerd
Model: HD MB40KG

Heb je hulp nodig?

Als je hulp nodig hebt met Adj HD MB40KG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Adj

Adj

Adj Hydro IP Tester Handleiding

15 November 2024
Adj

Adj Ultra Beam Bar 12CW Handleiding

5 November 2024
Adj

Adj UV Par 100IP Handleiding

5 November 2024
Adj

Adj PIXIE DRIVER 2000 V3 Handleiding

3 Juli 2024
Adj

Adj Jolt Panel FX2 Handleiding

27 Mei 2024
Adj

Adj Wifi Net 2 Handleiding

27 Mei 2024
Adj

Adj Par Z100 3K2 Handleiding

27 Mei 2024
Adj

Adj H2O Two Handleiding

27 Mei 2024
Adj

Adj Jolt Panel FXIP Handleiding

27 Mei 2024
Adj

Adj Pixie Curve 60 Handleiding

27 Mei 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx

Gourmetmaxx 03863 Handleiding

24 December 2024
Vello

Vello PGS-P Handleiding

24 December 2024
Venom

Venom Quad Charging Station VS4796 Handleiding

24 December 2024
Nec

Nec IPJ2000CM Handleiding

24 December 2024
Monogram

Monogram ZKPN Handleiding

24 December 2024
Philips

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024
Philips

Philips Senseo HD7002 Handleiding

24 December 2024
D-Link

D-Link DUB-C2 Handleiding

24 December 2024
Nec

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024
Nec

Nec DS1-TM01 Handleiding

24 December 2024