Adj DP-DMX20L Handleiding

Adj Niet gecategoriseerd DP-DMX20L

Lees hieronder de 📖 handleiding in het Nederlandse voor Adj DP-DMX20L (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

User Instructions

DP-DMX20L

4 CHANNEL DMX

DIMMER PACK

specications, diagrams, images, and instructions herein are

subject to change without notice. ADJ Products, LLC logo and

identifying product names and numbers herein are trademarks

of ADJ Products, LLC. Copyright protection claimed includes all

forms and matters of copyrightable materials and information

now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or

registered trademarks of their respective companies and are

hereby acknowledged. All non-ADJ Products, LLC brands and

product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim

any and all liabilities for property, equipment, building, and electrical

damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained

within this document, and/or as a result of the improper, unsafe,

unsucient and negligent assembly, installation, rigging, and

operation of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment.

Please turn o all electrical products when they are not in use. To

avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

Date Document

Version Notes

DOCUMENT VERSION

Please check www.adj.com for the latest revision/update of this guide.

02/07/18 1 Updated Release

Introduction:

Thank you for purchasing the DP-DMX20L™ 4 channel dimmer pack

from ADJ®. To optimize the performance of this product, please read

these operating instructions carefully and familiarize yourself with the

basic operations of this unit. The ADJ DP-DMX20L,®™ is a four channel,

DMX dimmer pack. This unit has been tested at the factory before

being shipped to you. There is no assembly required.

The ADJ DP-DMX20L™ is controlled via a standard DMX controller. ®

This unit allows you to control special eect lighting, that normally

could not be controlled, by a DMX controller. With this revision to our

popular DP-DMX20™ we have eliminated confusing dip switches and

replaced them with an easy to use digital switching device that incorporates

the use of an easy to read LCD display.

Customer Support:

ADJ Products, LLC provides a toll free customer support line, to provide

help and to answer any question should you encounter problems

during your set up or initial operation. You may also visit us on the web

at www.adj.com for any comments or suggestions. Service Hours are

Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (323) 582-2650

Fax: (323) 582-2941

E-mail: support@americandj.com

Warning!

To prevent or reduce the risk of electrical shock or re, do not expose

this unit to rain or moisture.

Caution!

There are no user serviceable parts inside this unit. Do not attempt any

repairs yourself, doing so will void your manufactures warranty. In the

unlikely event your unit may require service, please contact your nearest

ADJ dealer.®

ADJ Products, LLC® - www.adj.com - DP-DMX20L Instruction Manual Page 2

Power Supply: Before plugging your unit in be sure the source voltage

in your area matches the required voltage for your ADJ® DP-DMX20L.™

The DP-DMX20L™ is available in a 115v and 230v version. Because

line voltage may vary from venue to venue, you should be sure to plug

your power supply into a matching wall outlet before attempting to

operate you controller.

Data Cable (DMX Cable) Requirements:

Your unit and your DMX controller require an approved DMX-512 110

Ohm Data cable for data input and data output (Figure 1). We recommend

Accu-Cable DMX cables. If you are making

your own cables, be sure to use standard

110-120 Ohm shielded cable (This cable may

be purchased at almost all professional sound

and lighting stores). Your cables should be

made with a male and female XLR connector on

either end of the cable. Also remember that

DMX cable must be daisy chained and cannot

be split.

Notice: Do not use the ground lug on

the XLR connector. Do not connect the

cable’s shield conductor to the ground lug or allow the shield conductor

to come in contact with the XLR’s outer casing. Grounding the shield

could cause a short circuit and erratic behavior.

Figure 1

Figure 2

ADJ Products, LLC® - www.adj.com - DP-DMX20L Instruction Manual Page 3

Figure 3

XLR MALE SOCKET

1 EARTH 2 COLD

3 HOT

XLR FEMALE SOCKET

1 EARTHCOLD 2

3 HOT

XLR Pin Configuration:

Pin 1 = Shield

Pin 2 = Data Compliment (negative)

Pin 3 = Data ue (positive)Tr

DP-DMX20L DMX Set Up DP-DMX20L General Information

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMON

DMX512 OT

3-PIN XLR

1. Mode Button - This button will change the power packs operate

mode between DMX and chaser.

2. Menu Button - This button will activate the dierent functions in

DMX and chase modes.

3. Up Button - This button will increase the displayed value in the

LCD display.

4. Down Button - This button will decrease the displayed value in the

LCD display.

5. POWER OUTPUT - 3-prong grounded Edison output sockets. 8

total output sockets. Each channel has an output maxiimum of 6.3

amps. The unit has an output maximum of 15 amps

6. GREEN L.E.D. Indicators - These LEDs will indicate their relevant

channel activity.

7. LCD Display - This multifunction display will detail all chase and

program activity that pertains to the current operating mode of the

pack.

ADJ Products, LLC® - www.adj.com - DP-DMX20L Instruction Manual Page 5

Figure 5

1 42 3

2 4 3

Special Note: Line Termination.

When longer runs of cable are used, you may need to use a terminator on

the last unit to avoid erratic behavior. A terminator is a 90 - 120 ohm 1/4

watt resistor which is connected between pins 2 and 3 of a male XLR

connector (DATA + and DATA -). This unit is inserted in the female XLR

connector of the last unit in your daisy chain to terminate the line. Using

a cable terminator will decrease the possibilities of erratic behavior.

Product Description:

The DP-DMX20L,™ is 1, 2, or 4 channel DMX Dimmer Pack.

This pack can serve as a stand alone chaser or a DMX dimmer

pack. This pack is designed for zero-crossing circuitry which

protects against inductive loads, so it is safe for use with all

lighting eects that include transformers such as pin spots.

Each channel comes with two 3-prong Edison sockets inputs

for a total of eight. This unit features XLR female and male connection

for DMX compatibility. Each channel is equipped with a fuse for

each channel, and a maximum output load of 6.3A per chan-

nel or 15A total. This revision of our popular DP-DMX20™ has

a great new case design that makes it great for permanent or

mobile applications.

ADJ Products, LLC® - www.adj.com - DP-DMX20L Instruction Manual Page 4

DP-DMX20L Functions & Controls - Front Panel DP-DMX20L DMX Set Up

Termination educes signalr errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

Figure 4

Product specificaties

Merk:	Adj
Categorie:	Niet gecategoriseerd
Model:	DP-DMX20L
Soort bediening:	Knoppen
Kleur van het product:	Zwart
Ingebouwd display:	Ja
Gewicht:	2720 g
Breedte:	209 mm
Diepte:	260 mm
Hoogte:	76 mm
Stroombron:	AC
Aan/uitschakelaar:	Ja
Land van herkomst:	Verenigde Staten
Duurzaamheidscertificaten:	CE
AC-ingangsspanning:	120 V
AC-ingangsfrequentie:	60 Hz
Type beeldscherm:	LCD
DMX-ingang:	Ja
DMX-uitgang:	Ja
Aantal DMX-kanalen:	4 kanalen
Type DMX-connector:	XLR3