Adastra RMS1202 Handleiding

Adastra Receiver RMS1202

Lees hieronder de 📖 handleiding in het Nederlandse voor Adastra RMS1202 (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
RMS 1202
1U DUAL-ZONE MIXER- PLIFIER AM
Item ref: 4 953.15 UK
User Manual
Version 1 .0
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
953.154UK User Manual
Introduction
Thank you for choosing an Adastra RMS dual-zone mixer-amp as part of your sound system. 1202
This low impedance or 100V power amplifier has the advantage of selectable obal or individual inputs and a paging mic input. gl
Please read this manual to gain the best results from your product and avoid damage through misuse.
SAFETY SYMBOL AND MESSAGE CONVENTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this
unit
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
SAFETY NOTICE
1. Prior to use, read through this manual
2. Keep the manual in good condition
3. Pay attention to safety warnings
4. Observe all operating requirements
5. Do not use the device near water or wet areas
6. For cleaning, only use a lint-free, dry cloth
7. Install according to the specifications
8. Place away from heat sources or heating appliances
9. Use mains lead provided and avoid damage to cable or connectors
10. Unplug power from mains during stormy weather or if unused for long periods
11. In case of malfunction, water ingress or other damage, consult qualified service personnel
12. Do not place in damp areas or near liquids or moisture. Do not spill liquids on the housing
13. Please pay attention to warning symbols during transit and placement
14. Terminals marked with the symbol are HAZARDOUS LIVE and should only be connected by qualified personnel
15. Ensure that the apparatus is connected to a mains socket with a protective EARTH connection
16. Ensure correct operation of the mains switch
Warning
To prevent the risk of fire or electric shock, do not expose any components to rain or moisture.
If uids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by qualified personnel before liq
further use.
Avoid impact, extreme pressure or heavy vibration to the case
No user serviceable parts inside Do not open the case refer all servicing to qualified service personnel. – –
Safety
Check for correct mains voltage and condition of IEC lead before connecting to power outlet
Placement
This unit can be used free-standing or fixed int o a 19” rack
Ensure adequate support and access to controls and connectors when rack-mounting
Cleaning
Use a soft cloth with a neutral detergent to clean the housing as required
Do not use strong solvents for cleaning the unit
953.154UK User Manual
Front panel
Rear panel
Connection
Ensure the wer (12) is switched off until all input and output connections are in place. Po
Turn both output rotary level controls (9 fully down (anti-clockwise) to avoid loud noises when switching on. )
Set the BASS and TREBLE Tone controls (1, 2, 4, 5 to the vertical position (zero) )
Loudspeakers should be connected to the RMS via screw terminals on the 2 removable modular connectors. 1202
For standard low pedance speakers (4 , 8 , - i.e. not 100V type), use the bottom row of - terminals (16) im 16+/
Connect + and wires to each speaker as indicated, ensuring that there is no chance of strands shorting across terminals.
Important: Ensure that the load is no lower than 4 for each output. This can be Ω …
1 x 4 1 x 16 speaker Ω speaker Ω
1 x 8 2 x 16 speakers wired in parallel (8 ) Ω speaker Ω
2 x 8 (4 ) 3 x 16 speakers wired in parallel (5.3 ) Ω speakers wired in parallel Ω Ω
4 x 16 speakers wired in parallel (4 ) Ω Ω
Ensure that the connected speakers can handle 0W from each output. 12
If the speaker(s) being connected to an output channel
are V type, use the top row of termina (15) 100 ls
When connecting multiple 100V speakers to this output,
connect all speakers in parallel and aim to connect up to
90% of the maximum output power (i.e. 108 . W)
The wattage of each speaker can sometimes be
adjusted via tappings on the speaker (check the
speaker s documentation if unsure)
For either speaker output, choose whether the speakers connected will be 100V type
or standard low impedance (i.e 4 8 ) type. . Ω, Ω, 16Ω
DO NOT co ect to both 4 and 100V terminals for one tput channel nn Ωou
DO NOT mix 4 and 100V speakers on any single output. Ω
THERE SHOULD BE NO CONNECTIONS VERTICALLY ABOVE OR BELOW OTHER EACH
1.
BASS Paging Mic input EQ
7.
Power on dicator in
2.
TREBLE Paging Mic input EQ
8.
GAIN control Paging Mic input
3.
Signal indicator Paging Mic input
9.
LEVEL control Output channels
4.
BASS EQ Output channels
10.
Status indicators Output channels
5.
TREBLE Output channels EQ
11.
PAGE MIC on/off select
6.
INPUT select AUX or Individual annel Ch
12.
Power on/off switch
13.
IEC mains inlet and fuse holder
20.
Channel 1 balanced input screw terminals
14.
Cooling fan vents
21.
Auxiliary line output 2 x R sockets CA
15.
100V speaker output screw terminals
22.
Auxiliary line input 2 x RCA sockets
16.
4 speaker output screw terminals Ω
23.
Phantom power and Vox DIP switches
17.
Channel 2 balanced input screw terminals
24.
Paging mic VOX sensitivity control
18.
Channel 2 unbalanced input 2 x RCA sockets
25.
Paging mic balanced XLR input
19.
Channel 1 unbalanced input 2 x RCA sockets
26.
24V emergency mute termina ls


Product specificaties

Merk: Adastra
Categorie: Receiver
Model: RMS1202

Heb je hulp nodig?

Als je hulp nodig hebt met Adastra RMS1202 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Adastra

Handleiding Receiver

Nieuwste handleidingen voor Receiver