Acratech Leveling Base 1117 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Acratech Leveling Base 1117 (2 pagina's) in de categorie Statief. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
ACRATECH INC.
QUALITY PRECISION PRODUCTS
CAUTION: READ ALL INSTRUCTIONS BEFORE INSTALLING YOUR NEW
LEVELING BASE.
Thank you for purchasing the Acratech leveling base. Your new leveling base is
manufactured using the finest materials and workmanship. With proper care your
leveling base should last for many years.
The main adjustment knob and is used to tighten and loosen the ball so you can
adjust the leveling base. The knob is often only partially loosened so it will
maintain a controlled amount of friction or tension on the ball. The smaller knob is
preset and cannot be adjusted.
INSTALLING YOUR LEVELING BASE ON YOUR TRIPOD
1) If the threaded hole in the bottom of your new leveling base is larger in
diameter than the threaded stud on top of your tripod, then install the
brass reducer bushing provided. To do this you should use a small coin to
hand tighten the reducer bushing to moderate tightness. Measure the
length of the bolt sticking out of your tripod where you are going to install
your new Leveling Base. It should stick up at least ¼ in (6mm) and be no
longer than 3/8 in (9.5mm), if the bolt is too long it must be shortened
(Acratech can do this for a minimal charge).
2) Being careful not to cross thread, slowly tighten your new leveling base
onto your tripod “firmly hand tight”.
3) After installing your new leveling base, CAREFULLY make sure that it is
not interfering or binding on any part of your tripod. IF ANY
INTERFERING OR BINDING OCCURS, REMOVE THE LEVELING BASE
AND CONTACT ACRATECH BEFORE CONTINUING.
Leveling Base installation continued:
4) Make sure the leveling base is installed tight enough so it will not loosen
during use.
5) Use the same procedure listed above to install your tripod head onto your
leveling base.
6) When using any tripod, tripod head, or quick release system you should
always “ test the set-up” by securely grasping the camera and trying to
move it left, right, up, down, forward, back, etc. to make sure everything is
tight and secure before removing your hands from your camera. This
should be done every time you put any camera on any tripod.
7) The Acratech Leveling base is equipped with special knobs that cannot
vibrate loose and fall off. Do not try to remove knobs or loosen past the
point where resistance is felt.
8) Care for your new leveling base:
Keep your new ball head clean and free from debris.
Clean using a damp cloth, water or rubbing alcohol can be used.
DO NOT USE OIL OR WD40 ON THE BALL.
When storing you ballhead for long periods of time,
the knobs should not be rmly tightened.
Thank you for choosing an Acratech product. If your Leveling Base or other
Acratech product needs service or repair please send it directly to Acratech. Do
not return it to your dealer. If you have any questions or comments please call
us at (909) 394-1802 or E-mail us at info@acratech.net
Product specificaties
| Merk: | Acratech |
| Categorie: | Statief |
| Model: | Leveling Base 1117 |
Heb je hulp nodig?
Als je hulp nodig hebt met Acratech Leveling Base 1117 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Statief Acratech
8 Juni 2023
8 Juni 2023
Handleiding Statief
- Statief Braun
- Statief Sony
- Statief Nikon
- Statief Asus
- Statief Alpine
- Statief Aukey
- Statief Bresser
- Statief DJI
- Statief Dorr
- Statief Drift
- Statief Easypix
- Statief Godox
- Statief GoPro
- Statief Hama
- Statief Kodak
- Statief Kogan
- Statief Konig
- Statief Laserliner
- Statief Livoo
- Statief Neewer
- Statief Pyle
- Statief Ravelli
- Statief Revo
- Statief Rollei
- Statief Silvercrest
- Statief Sunpak
- Statief Trust
- Statief Vanguard
- Statief Velbon
- Statief Velleman
- Statief Vortex
- Statief Winegard
- Statief Omnitronic
- Statief Barska
- Statief Miller
- Statief Celestron
- Statief Levenhuk
- Statief Kessler
- Statief Eurolite
- Statief ARRI
- Statief JOBY
- Statief Vello
- Statief Swarovski
- Statief Testo
- Statief Carson
- Statief Benro
- Statief Magnus
- Statief Manfrotto
- Statief Sachtler
- Statief Sevenoak
- Statief Zhiyun
- Statief AVerMedia
- Statief MOZA
- Statief Cullmann
- Statief Stalco
- Statief GVM
- Statief Marshall Electronics
- Statief Rode
- Statief Slik
- Statief Celly
- Statief Gitzo
- Statief Proaim
- Statief Konig & Meyer
- Statief Ultimate Support
- Statief Oben
- Statief Glide Gear
- Statief Camgear
- Statief Libec
- Statief Redrock Micro
- Statief Auray
- Statief Ulanzi
- Statief Flycam
- Statief Gravity
- Statief Sirui
- Statief Vinten
- Statief ProMediaGear
- Statief Fidlock
- Statief Mantona
- Statief Olloclip
- Statief IFootage
- Statief SmallRig
- Statief FeiYu-Tech
- Statief FeiyuTech
- Statief Sky-Watcher
- Statief Hohem
- Statief MOVE'N SEE
- Statief On Air
- Statief Kaiser Fototechnik
- Statief Slidekamera
- Statief IOptron
- Statief FLOWCINE
- Statief SteadiCam
- Statief Fat Gecko
- Statief 3 Legged Thing
- Statief FLM
- Statief Peak Design
- Statief Easyrig
- Statief Robus
- Statief Studio Assets
- Statief Square Jellyfish
- Statief Tiltall
- Statief E-Image
- Statief MotoCrane
- Statief Cam Caddie
- Statief Cartoni
- Statief HPRC
- Statief Really Right Stuff
- Statief Ruggard
- Statief Ready Rig
- Statief Axler
Nieuwste handleidingen voor Statief
20 December 2024
20 December 2024
20 December 2024
20 December 2024
19 December 2024
19 December 2024
19 December 2024
19 December 2024
19 December 2024
19 December 2024