ACCU-CHEK Mobile Handleiding

ACCU-CHEK Bloedglucosemeter Mobile

Lees hieronder de 📖 handleiding in het Nederlandse voor ACCU-CHEK Mobile (146 pagina's) in de categorie Bloedglucosemeter. Deze handleiding was nuttig voor 260 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/146

User’s Manual and Quick

Start Guide

Blood glucose monitoring system

ACCU-CHEK, ACCU-CHEK MOBILE, ACCU-CHEK SMART PIX, ACCU-CHEK 360°,

ACCU-CHEK CONNECT and FASTCLIX are trademarks of Roche.

CONTINUA, the CONTINUA logos and CONTINUA CERTIFIED are trademarks,

service marks or certification marks of the Continua Health Alliance.

CONTINUA is a registered trademark in some, but not all countries in which

this product is distributed.

The USB-IF logos are trademarks of Universal Serial Bus Implementers

Forum, Inc.

M Roche Diabetes Care GmbH

Sandhofer Strasse 116

68305 Mannheim, Germany

www.accu-chek.com

08252963001(02)

Do Do not

Before testing your blood glucose: Wash your hands

with soap and warm water; rinse well to remove any

visible or invisible signs of glucose residue from, for

example, food or drink. Dry your hands thoroughly

with a clean towel.

Do perform a blood not

glucose test if the testing

site has not been washed or

is soiled or sticky (for

example, due to glucose

residue from, for example,

food or drink).

Always use a fresh, well-formed blood drop and

perform the test as quickly as possible after lancing.

Do not delay applying the

blood drop to the test area.

Do not perform a blood

glucose test with a smeared

or spread blood drop. Do not

smear the blood drop on the

test area.

When performing the test, place your finger gently on

the guidance tabs so that only the blood drop

comes into contact with the . centre of the test area

Your finger should not make any contact with the test

area. Keep your finger as still as possible.

Do attempt to force your not

finger between the guidance

tabs or apply any direct

pressure to the test area.

Avoid trembling or shaky

movements.

When the beep tone sounds and is Test in progress

displayed on the screen, remove your finger from the

test cassette immediately.

Note: You can only hear the beep tones when they

are turned on. See in the User’s Setting tones

Manual.

Do keep your finger on not

the guidance tabs or apply

pressure to the test area

after the beep tone sounds

and/or is Test in progress

displayed on the screen.

W IMPORTANT INFORMATION ON PERFORMING A BLOOD GLUCOSE TEST

An incorrectly performed blood glucose test may lead to incorrect test results which can cause the wrong therapy recommendation to be made and thus produce serious

adverse health effects. Therefore, the information on how to perform a blood glucose test correctly, carefully.read

IMMEDIATELY! DO NOT WAIT!

The meter and finger

pricker are intended for

personal use only!

They may only be used by

one and the same person

for performing a blood

glucose test. There is a risk

of infections being

transmitted if the meter or

finger pricker is used by

other people, even by family

members, or if healthcare

professionals use this meter

to test blood glucose or this

finger pricker to obtain

blood from different people.

This Quick Start Guide does

not replace the detailed

User’s Manual of your

Accu-Chek Mobile blood

glucose monitoring system.

Be sure to comply with the

safety information in the

User’s Manual and in the

package insert of the test

cassette.

1 Release button (priming

and pricking)

2 Power and enter button

3 Down/Up buttons

4 Window showing number

of available lancets

5 Lever for loading a new

lancet

6 Rotatable cap for setting

the penetration depth

7 Tip cover closed (below

right: open)

8 Test area (at the tip of the

cassette ready for a test)

9 Lancet drum

0 Slide button to release

the finger pricker

q Slide button to open the

cassette compartment

cover

w Tip cover

e Test cassette

r Guidance tabs

Why

An incorrectly performed blood

glucose test may lead to falsely

elevated blood glucose results

and thereby delivery of an

inappropriately high insulin

amount. Falsely elevated test

results are caused by the

following:

• Fingers have not been washed

or were soiled or sticky.

• If the blood drop spreads on

the finger or if the blood drop

becomes smeared on the test

area, the risk of contamination

of the test area increases

(for example, due to glucose

residue from, for example,

food or drink).

• The finger was pressed onto

the test area.

• Trembling or shaky

movements while performing

the blood glucose test.

• The blood glucose test was

not performed immediately or

the finger was resting on the

guidance tabs for too long.

Pay attention to the beep tone.

The beep tone helps you to

obtain a reliable test result.

Quick Start Guide

Start Here

Open the test cassette box at

the perforation. Take out the

plastic container.

Remove the new test cassette

from the plastic container.

Open the tip cover.

Push the slide button for the

cassette compartment cover

upwards in the direction of the

arrow.

Insert the test cassette in the

meter. Press the cassette

compartment cover closed.

Close the tip cover.

Pull the protective strip of the

batteries backwards out of the

meter. Remove the protective

ﬁlm from the display.

Press for about 2seconds

until the meter turns on.

Use to select a language

(highlighted in yellow).

Press .

Remove the cap from the ﬁnger

pricker.

Do remove the lancet drum not

until all 6lancets have been

used.

Insert the new lancet drum,

white end ﬁrst.

Place the cap back on again.

The cap is on correctly when it

is pushed back as far as it will

go, and you hear and feel it

click into place.

Rotate the cap until the desired

penetration depth lines up with

the indicator.

Tip: When obtaining blood, start

with a medium penetration

depth, such as 3.

Loading a new lancet: Prepare

the ﬁnger pricker for obtaining

blood again.

Push the lever

in direction A

and then back again in

direction .B

Wash your hands with warm

water and soap and rinse well.

Dry your hands thoroughly with

a clean towel before you obtain

blood.

Before you perform a blood

glucose test: Observe the

important instructions on

performing a blood glucose test.

Open the tip cover. Press the ﬁnger pricker ﬁrmly

against the selected puncture

site.

Press the release button all the

way down.

To apply the blood drop to the

test area: Position your ﬁnger

gently on the guidance tabs so

that the blood drop comes only

into contact with the test area

between the guidance tabs.

Testing is complete after

approximately 5seconds. Read

the test result and close the tip

cover.

Remove your ﬁnger from the

test cassette as soon as Test in

progress is displayed.

789

1. Starting to use the blood glucose monitoring system 2. Preparing the ﬁnger pricker 3. Performing a blood glucose test Customer Support and Service Centre

The lancet drum is properly

inserted when it is completely

inside the ﬁnger pricker and

only the front edge protrudes.

The cap can only be easily

placed on up to the stop

position when the lancet drum

is completely inside the ﬁnger

pricker. Do not use force to

place the cap on. This might

damage the cap and ﬁnger

pricker. Instead, correct the