A-NeuVideo ANI-2PIP-LOGO Handleiding

A-NeuVideo Router ANI-2PIP-LOGO

Lees hieronder de đź“– handleiding in het Nederlandse voor A-NeuVideo ANI-2PIP-LOGO (15 pagina's) in de categorie Router. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/15
ANI-2PIP-LOGO
2x1 HDMI Multiviewer
A-NeuVideo.com
Frisco, Texas 75036
INSTRUCTION MANUAL
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the
following items are contained included:
• ANI-2PIP-LOGO HDMI Multiviewer
• 5V/2.6A DC Power Adapter
• (3) 5-pin Terminal Block
• Shockproof Feet (Set of 4)
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your
equipment. Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of îšżre, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain,
water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean
dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and
plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken
so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper
AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may
impede the normal ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used
in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all
servicing to qualiîšżed service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports îšżrst, then remove the power cable; îšżnally, disconnect the interconnecting
cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship
the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualiîšżed service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY IN-
STRUCTIONS CONTAINED WITHIN THIS MANUAL.
A NEUVIDEO
A NEUVIDEO
2
TABLE OF CONTENTS
INTRODUCTION ...............................................................................................................................2
FEATURES APPLICATIONS / / SYSTEM REQUIREMENTS ..........................................................3
SPECIFICATIONS .............................................................................................................................4
OPERATION CONTROLS & FUNCTIONS .....................................................................................6
RS-232 ...............................................................................................................................................8
TELNET CONTROL ..........................................................................................................................9
WEBGUI CONTROL .......................................................................................................................18
CONNECTION DIAGRAM .............................................................................................................25
INTRODUCTION
The ANI-2PIP-LOGO HDMI Multiviewer is capable of scaling up to (2) sources and displaying both
simultaneously on a single HDMI output within their own windows. This is the ideal solution for
monitoring multiple sources simultaneously for use in control rooms, or for exible display presentations
in conference rooms or classrooms. Both inputs support resolutions up to 1920x1200@60Hz and
LPCM audio with up to 7.1 channels at 192kHz.
The multi-window output is sent to a single HDMI output at scaled resolutions up to 1920x1200@60Hz
along with the selected audio source. The HDMI output supports up to LPCM 7.1 digital audio while
the analog audio output supports up to LPCM 2.0. Each of the (2) HDMI sources may be displayed
individually, full screen, or they can be displayed using a variety of dual-window modes including
Picture-in-Picture, Side-by-Side, or freely positioned (with layer priority control). Each window
can also be mirrored, ipped, swapped, or frozen (with live audio). Chroma keying and a custom
uploadable logo/graphic are also supported.
External images can be uploaded and overlaid on top and at any position on the live HDMI Output.
This unit can be controlled easily by use of the front panel controls (with OSD) as well as by WebGUI,
Telnet, RS-232, IR and (8) direct trigger inputs. This product has a 3 year warranty.
FEATURES / APPLICATIONS / SY


Product specificaties

Merk: A-NeuVideo
Categorie: Router
Model: ANI-2PIP-LOGO

Heb je hulp nodig?

Als je hulp nodig hebt met A-NeuVideo ANI-2PIP-LOGO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Router A-NeuVideo

Handleiding Router

Nieuwste handleidingen voor Router