7inova 7W230 Handleiding

7inova Wifi-repeater 7W230

Lees hieronder de 📖 handleiding in het Nederlandse voor 7inova 7W230 (2 pagina's) in de categorie Wifi-repeater. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Before you start to use this device, please check if there’s anything

missing in the package, and contact your dealer of purchase to

claim for missing items:

Package Contents:

1x 7W230 WiFi Repeater

1x 1m Ethernet cable with RJ45 connector

1x Quick Installation Guide

Wireless Ceiling Mount Access Point 300M

Quick Installation Guide

Model 7W230：

LED indicators’ Status Description:

WPS/Reset

WLAN LED

Ethernet LED

Power LED

Cautions:

1. Disconnect the device in thunderstorms in case of lightning damage.

2. Keep far from heat source and ensure ventilation.

3. Keep waterproof in the storage, transportation and operating environment.

Indicator Name

Power Status Indicator Green On Get Powered

Status Description

Ethernet Status Indicator

Green fast blink

Green On

Data Transmission via Ethernet

Ethernet Connected

Wireless Status Indicator

Green slow blink Wireless Function Launched

Green fast blink Data Transmission via wireless

LAN

Reset: If need to reset the Repeater, press and hold RESET button for 3-5

seconds, release until all other LED are off except Power LED.

Note: Please check whether the WiFi-Repeater accord with factory default

settings once you can’t download http://192.168.2.1. If you are still not sure

what reasons, you can reset the WiFi-Repeater, just need to press the reset

button for 3-5 seconds, then try again.

Appearance Introduction

1 Computer Configuration

3 Configuration Mode

2 Connect To Wireless Network

1.1 Click “Start→Control Panel→Network and Internet→Network and Sharing

Center→Change adapter settings→Wi-Fi(right click)→Properties”

3.1.1 Follow process 2.3 to 2.5.

3.1.2 Select “ ” and enter the information what you want to set up wireless AP

information and password, then click “ ”, wait for 3~5 seconds it complete.Apply

3.1 Configure AP Mode

3.2.1 Follow process 2.3 to 2.5.

3.2.2 Select “ ” then click on “ ”.Repeater Search

3.2.3 Select wireless which you want to connect and enter the password (if wireless don’t

have password is “None”), then enter the wireless information what you want to set.

3.2.4 Then click “ ” and wait for 3~5 seconds it is complete.Apply

3.2 Configure Repeater Mode

3.3.1 Follow process 2.3 to 2.5

3.3.2 Select “ ” then click on “ ”Client Search

3.3 Configure Client Mode

2.6 After logging in click “ ” and then click “ ”, you Easy Mode Network Setting

will see 3 modes: AP Mode, Repeater Mode and Client Mode

2.1 Pulg the Wi-Fi Repeater to a wall socket.

2.2 Click on the network icon( ) on the right

bottom of your desktop. You will find the signal

from the Wi-Fi Repeater. Click on “ ” Connect

and wait for a few seconds.

2.3 Connect to a Network Connect to the When shows: “ ”, please click “

network without setting it up”

2.5 The login screen below will appear. Enter the “ ” and “Username Password”

then click “ ” to login. The default Username is “ ” and PasswordLogin admin

is “ ”.admin

2.4 Open web browser and type http://192.168.2.1 in the browser’s address

box. This number is the default IP address for this devices.

1.2 Double click “Internet Protocol Version 4(TCP/IPv4)”

1.3 To set up the computer IP 192.168.2.x (x arbitrary integer between 2~252),

subnet mask of 255.255.255.0, Click “ ”. Back to the last interface and OK

click “ ”OK

01 Wireless-N Repeater Wireless-N Repeater Wireless-N Repeater02 03

05 Wireless-N Repeater04 Wireless-N Repeater Wireless-N Repeater Wireless-N Repeater06 07

1) Restore the 7W230’s configuration to its factory default settings.

(With 7W230 powered on, use a pin to press and hold the Reset

button for about 3-5 seconds before releasing it).

2) To log in the Web Management page, use the default user name and

password: admin, admin. To connect to the Wireless Network, use

the default password on the label.

3) Try to configure 7W230 once again by following the instructions in

the previous steps of the QIG.

What can I do if I forgot my password?

Appendix: Troubleshooting

3.3.3 Select wireless which you want to connect and enter the password (if

wireless don’t have password is “None”)

3.3.4 Then click “ ” and wait for 3~5 seconds it is complete.Apply

5.2 Wireless Security Configuration

4 Reconnect to Repeater

4.1 Click “Start→Control Panel→Network and Internet→Network and Sharing

Center→Change adapter settings→Wi-Fi(right click)→Properties”

5 Configuring via Web Browser

5.1 Wireless Base Configuration

4.2 Double click “Internet Protocol Version 4(TCP/IPv4)”

4.3 Select “ ” and “Obtain an IP address automatically Obtain DSN

server address automatically”. Click “OK”. Back to the last

interface and click “OK”

4.4 3 Configuration ModeSelect the wireless network name configured in “ ” ,

click “ ” button.Connect

4.5 If you encrypted wireless network in “ ”, the following 3 Configuration Mode

message will be displayed on web browser, fill in password, click “OK”

Please click “Advanced Mode → Wireless Settings → Wireless Basic

Settings” located at the web management interface, the following

message will be displayed on your web browser:

You could configure the minimum number of Wireless settings for

communication, such as SSID and Channel. The Access Point can be set

simply with only the minimum setting items. Please click “Advanced Mode → Wireless Settings → Wireless Security

Settings” located at the web management interface, the following message

will be displayed on your web browser:

Setup the wireless security and encryption to prevent from unauthorized

access and monitoring. Supports 64/128-bit WEP, WPA-Personal, WPA2-

Personal encryption methods

5.3 Change Management password

Default password of Wireless Repeater is “ ”, and it’s displayed on admin

the login prompt when accessed from web browser. There’s a security risk

you don’t change the default password, since everyone can see it. This is

very important when you have wireless function enabled.

To change password, please follow the following instruction:

Please click “Advanced Mode → System Tools → User Password Change”

menu on the web management interface, the following message will be

displayed on your web browser:

5.4 Firmware Upgrade

The system software used by this repeater is called as “ ”, just like firmware

any applications on your computer, when you replace the old application

with a new one, your computer will be equipped with new function. You

can also use this firmware upgrade function to add new functions to your

repeater, even fix the bugs of this repeater.

Please click “Advanced Mode → System Tools → System Upgrade”

located at the located at the web management interface, then the

following message will be displayed on your web browser.

5.5 Settings Backup and Restore, Factory Default

You can backup all Setting of this repeater to a file, so you can make

several copied of repeater configuration for security reason.

To backup or restore repeater setting, please follow the following instruction:

Please click “Advanced Mode → System Tools → Backup and Recovery”

and “Advanced Mode → System Tools → Restore Factory Settings”

located at the web management interface, then the following message will

be displayed on your web browser:

If you want to keep original password unchanged, click “ ”.Cancel

Click “ ” button, the WiFi Repeater will become effectiveSave

Click “ ” button, the WiFi Repeater will become effective.Apply

Click “Browse” button first, you’ll be prompted to provide the filename of

firmware upgrade file. Please download the latest firmware file from our

website, and use it to upgrade your repeater.

After a firmware upgrade file is selected, click “ ” button, and the Upgrade

repeater will start firmware upgrade procedure automatically.

The procedure may take several minutes, please be patient.

Wireless Mode

Channel

SSID Broadcast

Supports 11b/g/n mixed modes

Wireless Signal On/Off

6(default)

Wireless Status

SSID

Wireless On/Off

Main Service Set Identifier.

It’s the “name” of your wireless network.

Back up

Browse

Restore All Settings

Press ”Back up” button, you can please save it as another

filename for different versions, and keep it in a safe place.

Press ”Browse” to pick a previously-saved configuration file

from your computer, and the click “Save”. After the replaced

by the file you just uploaded.

Click “Restore All Settings” button to remove all settings

Note: Never interrupt the upgrade procedure by closing the web browser or physically

disconnect your computer from repeater. If the firmware you upgrade is corrupt, the

firmware upgrade will fail, and you may have to return this repeater to the dealer of

purchase to ask for help. (Warranty voids if you interrupted the upgrade procedure).

Click “ ” and “ ” button. The repeater will restart.Save Restore All Settings

09 Wireless-N Repeater08 Wireless-N Repeater Wireless-N Repeater Wireless-N Repeater10 11

13 Wireless-N Repeater12 Wireless-N Repeater Wireless-N Repeater Wireless-N Repeater14 15

300Mbps Wireless Repeater

FW RVE: 7R152_V1.0

Browse

Click “ ” button, the WiFi Repeater will become effective.Apply

Product specificaties

Merk:	7inova
Categorie:	Wifi-repeater
Model:	7W230

Heb je hulp nodig?

Als je hulp nodig hebt met 7inova 7W230 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wifi-repeater 7inova

7inova 7W310 Handleiding

16 Juni 2023

7inova 7W230 Handleiding

16 Juni 2023

7inova 7W225 Handleiding

16 Juni 2023

7inova 7W211 Handleiding

16 Juni 2023

Handleiding Wifi-repeater

Nieuwste handleidingen voor Wifi-repeater

TP Link RE3000X Handleiding

15 November 2024

Medion P85032 (MD 87070) Handleiding

15 November 2024

HELGI HLG0372 Handleiding

10 November 2024

Mercusys Halo H1200G Handleiding

5 November 2024

D-Link DMG-112A Handleiding

2 November 2024

Xiaomi RA75 Handleiding

27 September 2024

Cudy RE3000 Handleiding

3 September 2024

Cudy RE1200 Handleiding

3 September 2024

Netgear EX6170 Handleiding

22 Augustus 2024

Extron FOX 3G HD-SDI SM Handleiding

15 Augustus 2024