ZTE MF80 Handleiding

ZTE Mobiele telefoon MF80

Lees hieronder de 📖 handleiding in het Nederlandse voor ZTE MF80 (4 pagina's) in de categorie Mobiele telefoon. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

ZTE CORPORATION

NO. 55, Hi-tech Road South, ShenZhen, P.R.China

Postcode: 518057 Tel: +86-755-26779999

URL: http://www.zte.com.cn E-mail: mobile@zte.com.cn

ZTE MF80

Quick Guide

Operate system Windows 7, Windows Vista(32bit or 64bit),

Windows XP (SP2 or later), MAC (10.4 or later)

Web Browser

IE (7.0 or later), Firefox (2.0 or later), Opera (10.0

or later), Safari (4.0 or later), Chrome (5.0 or

later)

Operating temperature 0°C ~ +40°C

Storage temperature -20°C ~ +50°C

Charging temperature 0°C ~ +45°C

Humidity 5%~ 95%

Notes: microSD is a trademark of SD Card Association.

The device’s standby and working time are only for your reference, and

based on ideal working environment.

Getting to Know Your Device

The following gure shows the appearance of the device, it is only for your

reference. The actual device may be different.

Right Side Front Left Side

Interface and Buttons

1. External Antenna

Connector

It is used to connect an external antenna to enhance

the signal strength.

2. Power Hold the button to switch on/off the device.Power

3. Connect

• Press it to connect to the Internet or disconnect

from the Internet.

• Hold it for more than 3 seconds to switch the

WAN Connection Mode between A(Always on) or

M(Manual).

4. WPS

This button is used to start/end Wi-Fi Protected Setup

authentication process and enable/disable the Wi-Fi

function.

• Hold it for more than 3 seconds to activate the WPS

function.

• Press it to enable/disable Wi-Fi function.

5. LED Screen It indicates the signal type, signal strength, battery, Wi-

Fi, etc.

6. Memory card slot

(microSD card) It is where you insert the memory card (microSD card).

7. Charger/USB

port

• Charge your device.

• Connect the client to your device via USB cable.

Notes:

Hold the and buttons simultaneously until the LED screen turns WPS Power

off, and then release the buttons. The device will restart automatically and

restore to the factory default settings.

LED Indicator

When the device is powered on, the following icons will appear on the LED

screen, with the corresponding indicates listed in the table below:

Icon Indication

Network signal strength.

Network type. 2G or 3G icon will appear on the LED

screen according to the network being connected.

Connect to the Internet automatically.

Connect to the Internet manually.

Roaming network indication.

New message received.

Wi-Fi Status and number of the connecting users.

Battery power indication.

Hardware Installation

Inserting SIM Card and Battery

1. Slide the battery cover, and remove it.

2. Insert the SIM card into the SIM card holder.

3. Insert the battery as shown with the contacts located against the metal

springs, and press the battery down into the case.

4. Put the battery cover of the modem atly upon the body of device. Direct

the battery cover towards the locking catches on the sides of the device,

and then push the battery cover to lock the cover into its place.

Inserting microSD Card

1. Pull the microSD cover out of the card slot.

Notes:

Do not pull the cover rudely, as it is connected with the device.

2. Insert the microSD card into the microSD slot. The following picture

shows the correct inserting direction. You will hear a click when the

microSD card locks in place.

3. Close the microSD cover.

Switching On/Off Your Device

Hold the button to switch on/off the device.Power

Notes:

The device is powered on when the LED screen lights up.

Charging Your Device

You can charge your device by using USB cable or adapter.

1. Insert the charger lead carefully with the plug arrow facing the bottom of

the device.

2. The plug only ts one way. Do not use excessive force to insert the plug.

3. Make sure the plug is the right way round and lined up correctly and

insert it gently.

Working Mode

Your device supports three working modes. For the client, we only use PC or

laptop as the example in this document.

USB Mode: Connect to the device with the USB cable.

Wi-Fi Mode: Connect to the device via Wi-Fi.

Mixed Mode: Connect to the device with the above two connection methods.

Notes:

If you want to connect to the Internet by using Wi-Fi mode, make sure that

the client supports the Wi-Fi function.

The following picture is the application example. All of the client devices can

surf on the Internet at the same time.

LEGAL INFORMATION

No part of this publication may be excerpted, reproduced, translated or utilized in

any form or by any means, electronic or mechanical, including photocopying and

microlm, without the prior written permission of ZTE Corporation.

The manual is published by ZTE Corporation. We reserve the right to make

modications on print errors or update specications without prior notice.

Version No. : R1.0

Establish a connection between your device and

the client

Via USB Cable

1. Connect your device and the client with the USB cable.

2. Power on your device.

3. Follow the system prompts to complete the software installation.

Notes:

• If the system does not launch installation automatically, you can run the

installation program in path of .My Computer > Mobile Hotspot

• The driver of your device will be installed at the same time.

4. After the installation, the system will create a shortcut icon on your

desktop and a program group in the Start→Programs menu. The

connection between your device and the client will be established

successfully a moment later.

Via Wi-Fi

1. Power on your device directly. It will take 1~2 minutes to initialize.

2. Use your normal Wi-Fi application on the client to search the available

wireless network.

Notes:

You need to check your Wireless Network Connection. Set the client

to obtain an IP address automatically in the Internet protocol (TCP/IP)

properties, and the client will get an IP address like “192.168.0.100”.

3. Select the SSID of your device, and then click .Connect

Introduction

ZTE MF80 is a 3G/2G mobile hotspot device, working in GSM/GPRS/

EDGE/WCDMA/HSPA/HSPA+ network. The client devices could connect to

it via USB or Wi-Fi interface. The device supports data and SMS services,

enabling you to communicate anytime and anywhere.

This quick guide provides instructions on how to install and get started with

the product. For information about connection of services, please consult

your service provider.

Specication

Data Service

HSPA+: DL 42Mbps

HSUPA: UL 5.76Mbps

WCDMA CS: 64kbps UL/DL

WCDMA PS: 384kbps UL/DL

Interface USB and Wi-Fi

Wi-Fi Standard 802.11b/g

Wi-Fi Security WEP/WPA/WPA2

USB Version USB 2.0 HIGH SPEED

USB Interface Type Micro USB

Weight 97g

Dimensions (W×H×D): 102mm*53mm*16.6mm

microSD card Support up to 32GB microSD card

Power Adapter 5V/1.5A

Battery 1900mAh

*Standby time 100hours

*Working time 4.5hours

123456789

Notes:

There will be a pop-up window to require the password. Check the label

on your device to gain the SSID and preset password information. Please

do remember the new password when you change the password by

selecting Settings > Wi-Fi Settings > Security after logging in the WebGUI

Conguration Page. You can restore the device to the factory default settings

in case you forget it.

4. Wait a moment, the connection between your device and the client will

be established successfully.

Access the Internet

1. Switch on the device.

2. Establish a connection between your device and the client.

3. After successfully establishing the connection, access the Internet in the

Always On Manual Always On and mode. The default mode is .

Notes:

You can browse the WebGUI Conguration page and click WAN Connection

to set the WAN connection mode.

PIN Code Verication

If the PIN code of your SIM card is enabled, you will need to input the PIN

code when you login at the rst time.

Notes: The SIM card will be locked if you enter wrong PIN code consecutively

for three times.

If you want to modify the PIN Status, please select Settings > Advanced >

PIN Management to do the actions.

Quick Settings

After logging in, select , and then the wizard appears.Quick Settings

The wizard guides you how to set the basic parameters for your device in the

safest way. After this procedure, you can use your Internet service.

Notes:

The parameter settings may have been preset by your service provider,

and you will enjoy your Internet service directly. Please contact your service

provider for details if you want to do some modication.

WAN Connection

After logging in, select WAN Connection, and you can choose the WAN

Connection Mode according to your requirement.

Settings

After logging in, select , and you can do the following operations.Settings

Select Settings >

3G Settings

View the Wireless Information, select Band Selection

Mode and change APN Setting..

Select Settings >

Wi-Fi Settings

View the current station list, change the basic wireless

network settings, choose security mode and WPA

type, and perform the WPS conguration.

Select Settings >

Firewall Set the IP/Port Filtering or Port Mapping.

Select Settings >

Advanced

View the current status of your device, change the

Administrator Settings, restore factory defaults,

manage PIN or set the LAN interface conguration.

Notes:

Make sure that you can remember the new password if you change the

restore the device to the factory default settings in case you forget the new

password.

Disconnect from the Internet

1. Log in the WebGUI Conguration page, and select WAN Connection.

2. Select Manual > Disconnect Internet.

3. Click Apply.

Notes:

Turning off the device can also terminate the internet connection.

SMS

This function allows you to view, send and receive short messages.

After logging in, select , and you can do the following operations.SMS

Select Operate the SMS in your device.SMS > Device

Select Operate the SMS in your SIM card.SMS > SIM Card

Select Send or save SMS.SMS > New Message

Select SMS > SMS Settings Set the SMS conguration.

• Your device is not waterproof. Please keep it dry and store in a shady

and cool place.

• Do not use your device immediately after a sudden temperature change.

In such case, it will produce dew inside and outside your device, so don’t

use it until it becomes dry.

• Handle your device carefully. Do not drop, bend or strike it. Otherwise

your device will be damaged.

• No dismantling by non-professionals and only qualied technicians can

undertake repair work.

• Operating temperature range of 0°C ~ +40°C and humidity range of

5% ~ 95% are recommended.

Using Battery

• Do not short-circuit the battery, as this can cause excessive heat and

re.

• Do not store battery in hot areas or dispose of it in a fire to avoid

explosion.

• Do not disassemble or modify the battery.

• When not using the battery for a long period, remove it from your device

and store it in a cool dry place.

• Never use any charger or battery damaged or worn out.

• Return the wear-out battery to the provider or put it in the appointed

recycle place. Do not put it in familial rubbish.

Warning:

If the battery is broken, keep away from it. If it taints your skin, wash your

skin with abundant fresh water and ask doctor help if necessary.

Limited Warranty

• This warranty does not apply to defects or errors in the Product caused

by:

i. Reasonable abrasion.

ii. End User’s failure to follow ZTE’s installation, operation or

maintenance instructions or procedures.

iii. End User’s mishandling, misuse, negligence, or improper installation,

disassembly, storage, servicing or operation of the Product.

iv. Modifications or repairs not made by ZTE or a ZTE-certified

individual.

v. Power failures, surges, re, ood, accidents, actions of third parties

or other events outside ZTE’s reasonable control.

vi. Usage of third-party products, or usage in conjunction with third-party

products provided that such defects are due to the combined usage.

vii. Any other cause beyond the range of normal usage intended for the

Product.

End User shall have no right to reject or return the Product, or receive a

refund for the Product from ZTE under the above-mentioned situations.

• This warranty is End User’s sole remedy and ZTE’s sole liability for

defective or nonconforming items, and is in lieu of all other warranties,

expressed, implied or statutory, including but not limited to the implied

warranties of merchantability and tness for a particular purpose, unless

otherwise required under the mandatory provisions of the law.

Limitation of Liability

ZTE shall not be liable for any loss of prots or indirect, special, incidental or

consequential damages resulting from or arising out of or in connection with

using of this product, whether or not ZTE had been advised, knew or should

have known of the possibility of such damages, including, but not limited to

lost prots, interruption of business, cost of capital, cost of substitute facilities

or product, or any downtime cost.

How to Get Help

You can get Help by:

• Sending E-mail to mobile@zte.com.cn

• Visiting http://www.zte.com.cn

• Calling Service Hotline: +86–755–26779999

Access the WebGUI Conguration Page

1. Make sure the connection between your device and the client is correct.

2. Launch the internet browser and enter http://192.168.0.1 or http://ufi.

home in the address bar.

Notes:

It is recommended that you use IE (7.0 or later), Firefox (2.0 or later), Opera

(10.0 or later), Safari (4.0 or later), Chrome (5.0 or later).

3. The login page appears as follows.

View the information of WAN, WLAN and Device. Input the case-sensitive

default password “ ”, and then click to access the WebGUI admin Login

Conguration page.

Notes:

• Do not put anything on the top of your device. Do not lay devices to

overlap each other when using.

• The device takes 1~2 minutes to initialize, and attach to the network.

PhoneBook

This function allows you to store contacts to your device or SIM card.

After logging in, select , and you can add a new contact in PhoneBook Add

New Device tab, and perform operations to the contact in the or tab.SIM Card

Usage of WPS

If your client device supports WPS, you need not to input the password

manually after WPS has been available. Please do the following:

1. Start up your device.

2. Launch the client device connected to your device.

3. Enable the WPS function of your device.

4. Enable the WPS function of the client.

Notes:

• If the current security mode of the device is OPEN SHARE or , the WPS

function is useless.

• For the detailed operations about the client, please refer to the client’s

instruction.

Sleep Mode

When you enable the Wi-Fi function and use the battery to supply power

to the device, once no user connects to the device within 10 minutes, the

device will enter the sleep mode, and the LED screen will be turned off. In

the sleep mode, the Wi-Fi function will be disabled. Press or Power WPS

button to wake up the device, and the LED screen will be turned on.

Warning and Notice

To the Owner

• Some electronic devices are susceptible to electromagnetic interference

sent by your device if inadequately shielded, such as the electronic

system of vehicles. Please consult the manufacturer of your device

before using if necessary.

• Operating of laptop and desktop PCs and your device may interfere with

medical devices like hearing aids and pacemakers. Please always keep

them more than 20 centimeters away from such medical devices when

they are turned on. Turn your device off if necessary. Consult a physician

or the manufacturer of the medical device before using your device.

• Be aware of the usage limitation when using your device at places such

as oil warehouses or chemical factories, where there are explosive gases

or explosive products being processed. Turn off your device if required.

• The use of electronic transmitting devices is forbidden in aircrafts, at

petrol stations and in hospitals. Please observe and obey all warning

signs and switch off your device in these conditions.

• Do not touch the inner antenna area if not necessary. Otherwise it will

affect your device’s performance.

• Store your device out of the reach of little children. Your device may

cause injury if used as a toy.

• Do not touch the metallic parts of your device so as to avoid a burn,

when your device is working.

Using Your Device

• Please use original accessories or accessories that are authorized. Using

any unauthorized accessories may affect your device’s performance, and

violate related national regulations about telecom terminals.

• Avoid using your device ne ar or inside metallic stru ctures or

establishments that can emit electromagnetic waves. Otherwise it may

inuence signal reception.

10 12 13 14 15 16 17 1811

Product specificaties

Merk:	ZTE
Categorie:	Mobiele telefoon
Model:	MF80

Heb je hulp nodig?

Als je hulp nodig hebt met ZTE MF80 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Mobiele telefoon ZTE

ZTE Concord II Handleiding

20 Juni 2023

ZTE N-860 Handleiding

13 Juni 2023

ZTE C-78 Handleiding

2 Juni 2023

ZTE G-R222 Handleiding

29 Mei 2023

ZTE T-165 plus Handleiding

28 Mei 2023

ZTE Light V9A Handleiding

27 Mei 2023

ZTE Grand X Max Handleiding

26 Mei 2023

ZTE Lever LTE Z936L Handleiding

17 Mei 2023

ZTE Light V9 Handleiding

11 Mei 2023

ZTE Rocket MF-591 Handleiding

10 Mei 2023

Handleiding Mobiele telefoon

Nieuwste handleidingen voor Mobiele telefoon

GPO Push Button Phone Handleiding

18 December 2024

Bea-fon SL671A Handleiding

14 December 2024

Bea-fon SL651A Handleiding

14 December 2024

Bea-fon S33 Handleiding

14 December 2024

Bea-fon C220 Handleiding

14 December 2024

Bea-fon SL470 Handleiding

14 December 2024

Bea-fon SL630 Handleiding

14 December 2024

Bea-fon SL652A Handleiding

14 December 2024

Bea-fon SL495 Handleiding

14 December 2024

Aiwa FPH-S100-4G Handleiding

12 December 2024