Zanussi ZDM17301WA Handleiding

Zanussi Vaatwasser ZDM17301WA

Lees hieronder de 📖 handleiding in het Nederlandse voor Zanussi ZDM17301WA (21 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/21

GETTING

STARTED?

EASY.

User Manual

ZDM17301SA

ZDM17301WA

EN User Manual

Dishwasher

VISIT OUR WEBSITE TO:

Get usage advice, brochures, trouble shooter, service and repair information:

www.zanussi.com/support

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible for any

injuries or damage that are the result of incorrect installation or

usage. Always keep the instructions in a safe and accessible

location for future reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

•This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning the use of the

appliance in a safe way and understand the hazards involved.

•Children between 3 and 8 years of age and persons with very

extensive and complex disabilities shall be kept away from the

appliance unless continuously supervised.

•Children of less than 3 years of age should be kept away from

the appliance unless continuously supervised.

•Do not let children play with the appliance.

•Keep detergents away from children.

•Keep children and pets away from the appliance when the door

is open.

•Children shall not carry out cleaning and user maintenance of

the appliance without supervision.

GENERAL SAFETY

•This appliance is intended to be used in household and similar

applications such as:

–farm houses; staff kitchen areas in shops, and otherofﬁces

working environments;

–by clients in hotels, motels, bed & breakfast and other

residential type environments.

•Do not change the of this appliance.speciﬁcation

•The operating water pressure (minimum and maximum) must be

between 0.3 (0.03) / 10 (1) bar (MPa)

•Follow the maximum number of 6 place settings.

•If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarly

qualiﬁed persons in order to avoid a hazard.

•WARNING: Knives and other utensils with sharp points must

be loaded in the basket with their points down or placed in a

horizontal position.

•Do not leave the appliance with the open door unattended to

avoid stepping accidentally onto it.

•Before any maintenance operation, deactivate the appliance

and disconnect the mains plug from the socket.

•Do not use high pressure water sprays and/or steam to clean

the appliance.

•If the appliance has ventilation openings in the base, they must

not be covered e.g. by a carpet.

•The appliance is to be connected to the water mains using the

new supplied hose-sets. Old hose sets must not be reused.

SAFETY INSTRUCTIONS

INSTALLATION

WARNING! Only a personqualiﬁed

must install this appliance.

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Follow the installation instructions supplied with

the appliance.

• Always take care when moving the appliance as

it is heavy. Always use safety gloves and

enclosed footwear.

• Do not install or use the appliance where the

temperature is less than 0 °C.

• Install the appliance in a safe and suitable place

that meets installation requirements.

ELECTRICAL CONNECTION

WARNING! Risk of and electricﬁre

shock.

• Warning: this appliance is designed to be

installed / connected to a grounding connection

in the building.

• Make sure that the parameters on the rating

plate are compatible with the electrical ratings

of the mains power supply.

• Always use a correctly installed shockproof

socket.

• Do not use multi-plug adapters and extension

cables.

• Make sure not to cause damage to the mains

plug and to the mains cable. Should the mains

cable need to be replaced, this must be carried

out by our Authorised Service Centre.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure that

there is access to the mains plug after the

installation.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• This appliance is with a 13 A mains plug. Ifﬁtted

it is necessary to change the mains plug fuse,

PRODUCT DESCRIPTION

GENERAL OVERVIEW

1 2 5 63

1Salt container

2Detergent dispenser

3Rinse aid dispenser

4Spray arm

5Filters

6Rating plate

7Drain hose

8Inlet hose connection

9Mains cable

10 Basket

11 Cutlery basket

12 Inlet hose

13 Funnel

CONTROL PANEL

1 2 2 543 6 7

1On / Off

2Programme indicators

3Indicators

4Display

5Delay start

6Programme

7Start / Pause

INDICATORS

Indicator Description

It is on when the rinse aid dispenser needs It is always off while the pro-reﬁlling.

gramme operates.

It is on when the salt container needs It is always off while the programmereﬁlling.

operates.

PROGRAMMES

PROGRAMME OVERVIEW

Programme Degree of soil

Type of load Programme phases Detergent pre-wash /

main wash (g) Rinse aid

Heavy, dried-on soil-

ing, pans, pots, cas-

serole dishes

• Pre-wash 50 °C

• Dishwash 70 °C

• Rinse 70 °C

• Drying

3 / 15

Normal soiling, pots,

plates, glasses, pans

• Pre-wash

• Dishwash 60 °C

• Rinse 70 °C

• Drying

3 / 15

Normal soiling,

crockery, cutlery

• Pre-wash

• Dishwash 45 °C

• Rinse 65 °C

• Drying

- / 14

Programme Degree of soil

Type of load Programme phases Detergent pre-wash /

main wash (g) Rinse aid

Normal or light soil-

ing, glasses, crystal,

ﬁne china

• Dishwash 45 °C

• Rinse 60 °C

• Drying

- / 18

Fresh soiling, coffee

cup, glasses

• Dishwash 45 °C - / 15

Light soiling, all types

of dish load

• Dishwash 40 °C

• Rinse - / 15

1) This programme offers the most use of water and energy consumption for crockery and cutleryefﬁcient

with normal soil. This is the standard programme for test institutes. This programme is used to assess

compliance with the UK Ecodesign for Energy-Related Products and Energy Information Regulations.

CONSUMPTION VALUES

Programme 1) 2) Duration (min) Energy (kWh) Water (l)

140 1.20 9.6

120 1.05 7.7

230 0.613 6.5

75 0.65 5.8

20 0.39 7.0

30 0.50 5.8

1) The pressure and the temperature of the water, the variations of the mains supply, the options, the quan-

tity of dishes and the degree of soil can change the values.

2) The values for programmes other than ECO are indicative only.

INFORMATION FOR TEST INSTITUTES

To receive the necessary information for conducting

performance tests (e.g. according to: BS

EN60436 ), send an email to:

info.test@dishwasher-production.com

In your request, include the product number code

(PNC) from the rating plate.

For any other questions regarding your dishwasher,

refer to the service book provided with your

appliance.

BEFORE STARTING A PROGRAMME

Before you start the selected programme, make

sure that:

• The are clean and correctly installed.ﬁlters

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is enough salt and rinse aid (unless you

use multi-tablets).

• The arrangement of the items in the baskets is

correct.

• The programme is suitable to the type of load

and the degree of soil.

• The correct quantity of detergent is used.

USING A PROGRAMME

1. Close the appliance door.

2. Open the water tap.

3. Press the On / Off button to activate the

appliance.

4. Press Programme button until the indicator of

the selected programme comes on.

5. Press Start / Pause button to start the

programme.

When a programme is completed, an intermittent

acoustic signal sounds for a few seconds.

6. Press On / Off button to deactivate the

appliance.

The appliance turns off automatically in 15

minutes after the programme ends.

7. Close the water tap.

Wait until the dishes are cold before you remove

them from the appliance.

There can be water on the sides and

the door of the appliance.

CANCELLING A PROGRAMME

1. Press the Start / Pause button.

2. Press and hold Programme button for 3

seconds.

The appliance comes back to its initial settings.

Make sure that there is detergent in

the detergent dispenser before you

start a new programme.

INTERRUPTING A PROGRAMME

1. Open the appliance door.

The appliance stops.

2. Close the appliance door.

The programme continues from the point of

interruption.

STARTING A PROGRAMME WITH DELAY

START

1. Close the appliance door.

2. Open the water tap.

3. Press the On / Off button to activate the

appliance.

4. Set a programme.

5. Press Delay start button to delay start of a

programme by up to 24 hours.

6. Press Start / Pause button to start the

countdown.

":" symbol ﬂashes.

When the countdown is completed, the programme

starts automatically.

CANCELLING DELAY START

1. Press Start / Pause button.

2. Press Delay start button until 0 comes on.

3. Press Start / Pause button.

The programme starts automatically.

DAILY USE

USE OF THE APPLIANCE

1. Fill the salt container with salt for dishwashers.

2. Fill the rinse aid dispenser with rinse aid.

3. Load the basket.

4. Open the water tap.

5. Set the correct programme for the type of load

and the degree of soil.

6. Add the detergent.

7. Start the programme.

FILLING THE SALT CONTAINER

CAUTION! Use only salt designed for

dishwashers.

1. Turn the cap of the salt container

counterclockwise and remove it.

2. Put 1 litre of water in the salt container (Only

for the time).ﬁrst

3. Use the funnel to the salt container withﬁll

dishwasher salt.

4. Remove the salt around the opening of the salt

container.

5. Turn the cap of the salt container clockwise to

close the salt container.

Water and salt can come out from the

salt container when you it, whichﬁll

causes corrosion. To prevent it, start a

programme immediately after theﬁlling

salt container.

THE WATER SOFTENER

The water softener removes minerals from the water

supply, which would have a detrimental effect on

the washing results and on the appliance.

The higher the content of these minerals, the harder

your water is. Water hardness is measured in

equivalent scales.

The water softener should be adjusted according to

the hardness of the water in your area. Your local

water authority can advise you on the hardness of

the water in your area. Set the right level of the

water softener to assure good washing results.

Water hardness

German de-

grees (°dH)

French degrees

(°fH) mmol/l Clarke de-

grees

Setting on the

water softener Setting indication

0 - 5 0 - 9 0.0 - 0.9 0 - 7 1 H1

6 - 11 10 - 19 1.0 - 2.0 8 - 14 2 H2

12 - 17 20 - 30 2.1 - 3.0 15 - 21 3 H3

18 - 22 31 - 39 3.1 - 4.0 22 - 27 4 1) H4

23 - 34 40 - 60 4.1 - 6.1 28 - 42 5 H5

35 - 45 61 - 80 6.2 - 8.0 43 - 56 6 H6

1) Factory setting.

Regardless of the type of detergent used, set the

proper water hardness level to keep the salt reﬁll

indicator active.

Multi-tabs containing salt are not

effective enough to soften hard water.

Regeneration process

For the correct water softener operation, the resin

of the softener device needs to be regenerated

regularly. This process is automatic and is the part

of the normal dishwasher operation.

Water softener

level Regeneration frequency

1 off

2 every 10 cycles

3 every 5 cycles

4 every 3 cycles

5 every 2 cycles

6 every cycle

Regeneration and softener rinse takes place in the

drying phase and ends with a complete drain. This

activity lasts around three minutes, but it does not

impact the overall cycle time. This activity increases

the total water consumption of a programme by

additional 1 l and the total energy consumption of a

programme by additional 0.3 Wh.

All the consumption values mentioned

in this section are determined in line

with the currently applicable standard

in laboratory conditions with water

hardness 2.5mmol/L (water softener:

level 3) according to the regulation:

UK Ecodesign 2021/745.

The pressure and the temperature of

water as well as the variations of the

mains supply can change the values.

CHANGING WATER SOFTENING SETTING

1. Close the appliance door.

2. Press On / Off button.

3. Press and hold Programme button immediately

for 6 seconds.

The display shows the current water softener level.

4. Press Programme button to select the water

softening level.

The level is set after 6 seconds.

FILLING THE DETERGENT DISPENSER

CAUTION! Use only detergents for

dishwashers.

1. Press the release button to open the lid of the

detergent dispenser.

A B

2. Put the detergent (approximately 15 g) in the

compartment ( ). Put detergent tablets in partC

( ) of the compartment.E

D E

a. If the programme has a prewash phase,

put a small quantity of detergent

(approximately 3 g) on the lid of the

detergent dispenser.

3. Close the detergent dispenser. Press the lid

until the release button locks into position.

Reﬁll the detergent dispenser before

each wash cycle.

USING DETERGENT, SALT AND RINSE AID

SEPARATELY

1. Fill the salt container and the rinse aid

dispenser.

2. Start a programme without loading dishes.

3. When the programme is completed, adjust the

position of the rinse aid dispenser.

USING THE RINSE AID DISPENSER

CAUTION! Use only rinse aid

designed for dishwashers.

Rinse aid helps to dry the dishes without streaks

and stains. The rinse aid is automatically released

during the last rinsing phase.

1. Turn the rinse aid dispenser cap

counterclockwise and remove it.

2. Fill the rinse aid dispenser with rinse aid.

The mark ''MAX'' shows the maximum level.

3. Remove the spilled rinse aid with an absorbent

cloth to prevent too much foam during the

programme.

4. Put the cap on again and turn it clockwise until

it locks.

Make sure that the signs on the cap and on

the dispenser are aligned.

5. Turn the rinse aid selector (A) to adjust the

dosage.

HINTS AND TIPS

GENERAL

Follow the hints below to ensure optimal cleaning

and drying results in daily use and to protect the

environment.

• Washing dishes in the dishwasher as instructed

in the user manual usually consumes less water

and energy than washing dishes by hand.

• Load the dishwasher to its full capacity to save

water and energy. For best cleaning results,

arrange items in the baskets as instructed in the

user manual and do not overload the baskets.

• Do not pre-rinse dishes by hand. It increases

the water and energy consumption. When

needed, select a programme with a prewash

phase.

• Remove larger residues of food from the dishes

and empty cups and glasses before putting

them inside the appliance.

• Soak or slightly scour cookware with ﬁrmly

cooked-on or baked-on food before washing it

in the appliance.

• Make sure that items in the baskets do not

touch or cover each other. Only then can the

water completely reach and wash the dishes.

• You can use dishwasher detergent, rinse aid

and salt separately or you can use the multi-

tablets (e.g. ''All in 1''). Follow the instructions

on the packaging.

• Select a programme according to the type of

load and the degree of soil. ECO offers the

most use of water and energyefﬁcient

consumption.

• To prevent limescale buildup inside the

appliance:

– the salt container wheneverReﬁll

necessary.

– Use the recommended dosage of the

detergent and rinse aid.

– Make sure that the current level of the water

softener agrees with the hardness of the

water supply.

– Follow the instructions in the chapter "Care

and cleaning".

USING SALT, RINSE AID AND DETERGENT

• Only use salt, rinse aid and detergent designed

for dishwasher. Other products can cause

damage to the appliance.

• In areas with hard and very hard water, we

recommend to use basic dishwasher detergent

(powder, gel, tablets containing no additional

agents), rinse aid and salt separately for optimal

cleaning and drying results.

• Detergent tablets do not fully dissolve with short

programmes. To prevent detergent residues on

the tableware, we recommend that you use

tablets with long programmes.

• Always use the correct quantity of detergent.

Insufﬁcient dosage of detergent can result in

poor cleaning results and hard-water orﬁlming

spotting on the items. Using too much detergent

with soft or softened water results in detergent

residues on the dishes. Adjust the amount of

detergent based on the water hardness. Refer

to the instructions on the detergent packaging.

• Always use the correct quantity of rinse aid.

Insufﬁcient dosage of rinse aid decreases the

drying results. Using too much rinse aid results

in bluish layers on the items.

• Make sure that the water softener level is

correct. If the level is too high, the increased

quantity of salt in the water might result in rust

on cutlery.

USING THE BASKETS

• Always use the whole space of the baskets.

• Use the appliance to wash dishwasher-safe

items only.

• Do not wash in the appliance items made of

wood, horn, aluminium, pewter and copper as

they could crack, warp, get discoloured or

pitted.

• Do not wash in the appliance items that can

absorb water (sponges, household cloths).

• Put hollow items (cups, glasses and pans) with

the opening facing downwards.

• Make sure that glass items do not touch each

other.

• Mix spoons with other cutlery to prevent them

from bonding together.

• The cutlery basket has 2 cutlery grids that can

be easily removed.

• Make sure that the spray arms can move freely

before you start a programme.

• Let the tableware cool down before you remove

it from the basket. Hot items can be easily

damaged.

CARE AND CLEANING

MAINTENANCE

WARNING! Before maintenance,

deactivate the appliance and

disconnect the mains plug from the

mains socket.

CAUTION! Do not use the appliance

without ﬁlters.

Make sure that the are correctlyﬁlters

positioned. An incorrect positioning of

the will cause bad washingﬁlters

results and damage to the appliance.

Dirty and a clogged spray armﬁlters

decrease the washing results.

Regularly check and if necessary,

clean the ﬁlters.

REMOVING AND CLEANING THE FILTERS

1. Turn the (B) counterclockwise andﬁne ﬁlter

remove the assembly.ﬁlter

2. Remove the coarse (A) by pulling it outﬁlter

from the (B).ﬁne ﬁlter

3. Wash the with water and a brush.ﬁlters

4. Put the coarse (A) into the (B).ﬁlter ﬁne ﬁlter

5. Put the assembly into the tub and turn theﬁlter

ﬁne ﬁlter (B) clockwise until it locks.

CLEANING THE SPRAY ARM

Do not remove the spray arm. If the openings in the

spray arm are clogged, remove remaining parts of

soil with a thin pointed object.

EXTERNAL CLEANING

• Clean the appliance with a moist soft cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive cleaning

pads or solvents.

INTERNAL CLEANING

• Carefully clean the appliance, including the

rubber gasket of the door, with a soft damp

cloth.

• To maintain the performance of your appliance,

use a cleaning product designed forspeciﬁcally

dishwashers at least once a month. Carefully

follow the instructions on the packaging of the

product.

• Do not use abrasive products, abrasive cleaning

pads, sharp tools, strong chemicals, scourer or

solvents.

• Using short-duration programmes regularly can

cause grease and limescale buildup inside the

appliance. Run long-duration programmes at

least twice a month to prevent the buildup.

REMOVAL OF FOREIGN OBJECTS

Check the and the sump after each use of theﬁlters

dishwasher. Foreign objects (e.g. pieces of glass,

plastic, bones or toothpicks, etc) decrease the

cleaning performance and can cause damage to

the drain pump.

CAUTION! If unable to remove the

foreign objects, contact an Authorised

Service Centre.

1. Disassemble the system as instructed inﬁlters

this chapter.

2. Remove any foreign objects manually.

3. Reassemble the as instructed in thisﬁlters

chapter.

TROUBLESHOOTING

WARNING! Refer to Safety chapters.

WHAT TO DO IF...

With some problems programme indicators intermittently indicating a malfunction.ﬂash

Problem Possible solution

You cannot activate the appliance. • Make sure that the mains plug is connected to the mains

socket.

• Make sure that there is no damaged fuse in the fuse box.

The programme does not start. • Make sure that the appliance door is closed.

• Press the start button.

• If the delay start is set, cancel the setting or wait for the

end of the countdown.

The appliance does not drain the

water.

• Make sure that the drain hose is correctly connected.

• Make sure that the in the appliance are clean.ﬁlters

• Make sure that the kitchen sink drains correctly.

The appliance does not with wa-ﬁll

ter and an intermittent acoustic sig-

nal sounds for approximately 30

seconds.

The display shows E1.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too

low. For this information, contact your local water authority.

• Make sure that the water tap is not clogged.

The required temperature is not

reached.

The display shows E3.

• Contact an Authorised Service Centre.

The water drain hose must be less than 600 mm

from the bottom of the appliance to prevent

problems during the draining phases.

Remove the sink plug when the appliance drains

water to prevent that the water goes back into the

appliance.

The extension of the water drain hose must not be

longer than 2 m. The internal diameter must not be

smaller than the diameter of the drain hose.

If you connect the water drain hose to a trap spigot

under the sink, remove the plastic membrane ( ). IfA

you do not remove the membrane, remaining food

can cause a blockage in the drain hose spigot.

FINAL CHECK

Before you turn on the dishwasher check if:

• The appliance is levelled and properly.ﬁxed

• The inlet valve is open.

• Inlet hose connections are fully tightened and

not leaking.

• The wires are tightly connected.

• The power is switched on.

• The inlet and drain hoses are knotted.

• All packing materials and printings are removed

from the dishwasher.

TECHNICAL DATA

TECHNICAL INFORMATION

Height (mm) 438

Width (mm) 550

Depth (mm) 500

Depth with the door fully

open (mm):

812

Voltage connected load: see rating

plate

Water pressure (MPa): 0.4 (0.04) /

10 (1)

Power supply: see rating

plate

Place settings: 6

LINK TO THE PRODUCT INFORMATION

SHEET

The QR code on the energy label supplied with the

appliance provides a web link to the product

information sheet. Keep the energy label for

reference together with the user manual and all

other documents provided with this appliance.

For more detailed information about the energy

label, visit www.theenergylabel.eu.

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put the

packaging in relevant containers to recycle it. Help

protect the environment and human health by

recycling waste of electrical and electronic

appliances. Do not dispose of appliances marked

with the symbol with the household waste.

Return the product to your local recycling facility or

contact your municipal ofﬁce.

Product specificaties

Merk:	Zanussi
Categorie:	Vaatwasser
Model:	ZDM17301WA
Apparaatplaatsing:	Vrijstaand
Soort bediening:	Knoppen
Ingebouwd display:	Ja
Breedte:	550 mm
Diepte:	500 mm
Hoogte:	438 mm
Netbelasting:	1180 W
Aantal couverts:	6 couverts
Droogsysteem:	Restwarmte
Deurkleur:	Wit
Snoerlengte:	1.5 m
Resterende tijd indicatie:	Ja
Wi-Fi-besturing:	Nee
Droogklasse:	A
Duur cyclus:	- min
Geluidsniveau:	52 dB
Jaarlijks energieverbruik:	175 kWu
Energie-efficiëntieklasse (oud):	A+
Geschikt voor paneelaanpassing:	Nee
Waterconsumptie per cyclus:	6.5 l
Wasklasse:	A
Stroom:	10 A
Geïntegreerde timer:	Ja
Aantal wasprogramma's:	6
Verstelbare voeten:	Ja
Productafmeting:	Compact
Kleur bedieningspaneel:	Wit
Afwasprogramma's:	Glass/delicate, Intensive 70°C, Normal, Quick
Energieverbruik per cyclus:	- kWu
Jaarlijks waterverbruik:	1820 l
Lengte afvoerslang:	1.5 m
Lengte watertoevoerslang:	1.5 m
Temperatuur (max):	70 °C
Watertoevoer:	Cold, Hot
AC-ingangsspanning:	230 V
AC-ingangsfrequentie:	50 Hz