Yamaha VXS10S Handleiding

Yamaha Speaker VXS10S

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha VXS10S (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 96 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of

serious injury or even death from electrical shock, short-circuiting, damages,

fire or other hazards. These precautions include, but are not limited to, the

following:

• This device contains no user-serviceable parts. Do not open the device or attempt

to disassemble the internal part s or modify them in any way. If it should appear to

be malfunctioning, discontinue use immediately and have it inspected by qualified

Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions, or

place on it any containers (such as vases, bottles or glasses) containing liquids

which might spill into any openings. If any liquid such as water seeps into the

device, have the device inspected by qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of

physical injury to you or others, or damage to the device or other property.

These precautions include, but are not limited to, the following:

• Do not place the device in an unstable position where it might accidentally fall over.

• Do not place the device in a location where it may come into contact with corrosive

gases or salt air. Doing so may result in malfunction.

• Construction work should be carried out in accordance with construction-related

law and always by a professional constructor. If the device installation requires

construction work, make sure to observe the following precautions.

- Choose mounting hardware and an installat ion locat ion that can support the

weight of the device.

- Avoid locat ions that are exposed to constant vibration.

- Use the required tools to install the device.

- Inspect the device periodically.

• When transporting or moving the device, always use two or more people.

Attempting to lift the device by yourself may damage your back, result in other

injury, or cause damage to the device itself.

• Before connecting the device to a power amplifier, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to minimum.

• Use only speaker cables for connecting speakers to the speaker connectors. Use of

other types of cables may result in fire.

• Do not wipe the outer packaging wit h benzine, thinner, or synthet ic detergent and

do not use electrical contact cleaner. These may damage the outer packaging and

dissolve the parts.

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) int o holes of

the grille. If this happens, have the device inspected by qualified Yamaha service

personnel.

• Do not operate the device if the sound is distorting. Prolonged use in this condition

could cause overheating and result in fire.

• When choosing a power amplifier for use with this device, make sure that the output

power of the amplifier is lower than the power capacity of this device (see

SPECIFICATIONS).

Even if the output power of the amplifier is lower than the power capacity of this

device (PGM), use of excessive input signals resulting in clipping may cause

damage to the device.

Malfunction or fire may occur especially when the following sounds or noises are

generated:

- feedback, when using a microphone

- continuous and extreme volume sound from a musical instrument

- extreme cont inuous dist orted sound

- noise caused by plugging/unplugging the cable while the amplifier is turned on

PRECAUTIONS

Do not open

Water warning

Location

Connections

Maintenance

Handling caution

NOTICE

To avoid the possibility of malfunction/damage to the product or damage to other

property, follow the not ices below.

ƔHandling and Maintenance

• Do not place vinyl, plastic or rubber objects on the device, since this might discolor

the cabinet.

• When cleaning the device, use a dry and soft cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnat ed wiping cloths.

• Condensat ion can occur in the device due to rapid, drastic changes in ambient

temperature-when the device is moved from one location to another, or air

conditioning is turned on or off, for example. Using the device while condensat ion is

present can cause damage. If there is reason to believe that condensation might

have occurred, leave the device for several hours until the condensation has

completely dried out.

• Be sure to observe the amplifier’s rated load impedance (see SPECIFICATIONS),

particularly when connecting speakers in parallel. Connecting an impedance load

out side the amplifier’s rated range can damage the amplifier.

• When connecting the speakers with high impedance, be sure that the output t otal of

each speaker does not exceed the rated output of the power amplifier.

• ABOUT THE PROTECTION CIRCUIT

This speaker system has an internal protection circuit that shuts off the speaker unit

when an excessive input signal is applied.

If the speaker unit emits no sound, reduce the volume level of the amplifier

immediat ely.

The sound will return aut omatically in several seconds.

• Place the speaker on a flat and smooth surface.

ƔAbout This Manual

The illust rations as shown in this manual are for instructional purposes only, and may

appear somewhat different from those on your device.

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the device.

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying

documents means that used electrical and electronic products

should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please

take them to applicable collection points, in accordance with your

nat ional legislation and the Direct ives 2002/96/EC.

By disposing of these products correctly, you will help to save

valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from inappropriate

waste handling.

For more inf ormation about collection and recycling of old products, please contact

your local municipality, your waste disposal service or the point of sale where you

purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer

or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items,

please contact your local authorities or dealer and ask for the correct method of

disposal.

UNPACKING

Unpack the contents and confirm that all the following items are included.

• Speaker × 1

• Bracket base × 1

• Mounting bracket × 1

• Captive washer screw × 4

• Rubber spacer × 4 (14 mm thickness)

• Hexagon bolt × 4

• Spring washer × 4

• Flat washer × 4

• Safety wire × 1

• Owner’s Manual (this manual)

* Screws/bolts to fasten the bracket onto the wall and speaker cables are not included.

SPECIFICATIONS

*1: Half-space (2π)

*2: Calculated based on power rating and sensitivity, exclusive of power compression.

*3: Impedance lower limit (per satellite output) VXS10S/VXS10SW: 4 Ω, VXS10ST/VXS10STW: 8 Ω

The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual

may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since

specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

The dimensions are shown overleaf.

VXS10S/VXS10SW VXS10ST/VXS10STW

Type Subwoofer, Bass reflex

Component 10" (25 cm) Cone driver, Dual voice coil

Nominal impedance 8 Ω + 8 Ω –

Power rating NOISE 100 W + 100 W –

PGM 200 W + 200 W –

MAX 400 W + 400 W –

Sensitivity (1W, 1m) * 1 96 dB SPL 96 dB SPL

Maximum SPL (Calculated, 1m) * 2 125 dB SPL –

Frequency range (-10 dB) * 1 45 Hz – 250 Hz 45 Hz – 250 Hz

Subwoofer filter Network: Low-pass filter 6 dB/Oct, 200 Hz

Acoustic filter: Low-pass filter 6 dB/Oct, 200 Hz

Satellite filter Network: High-pass filter 6 dB/Oct, 200 Hz

Satellite impedance 8 Ω load per satellite output recommended * 3

Connector Euroblock (4 pin) × 1:

Input (CH1: +/-, CH2: +/-)

Euroblock (4 pin) × 1:

Input (input: +/-, loop-thru: +/-)

Euroblock (4 pin) × 1: Satellite output (ST1: +/-, ST2: +/-)

– Euroblock (5 pin) × 1: transformer taps

Transformer taps 70 V – 200 W, 100 W, 50 W, 25 W

100 V – 200 W, 100 W, 50 W

Overload protection Full-range power limiting to protect network and transducers

Magnetically shielded No

Enclosure Shape Rectangle

Cabinet material MDF

Finish VXS10S/VXS10ST: Black (PVC, approximate value: Munsell N3)

VXS10SW/VXS10STW: White (PVC, approximate value: Munsell 3.5PB9.0/1)

Dimensions (Speaker only) 260 × 500 × 389 mm (10.2" × 19.7" × 15.3")

Net weight (Speaker only) 16.5 kg (36.4 lb) 19.5 kg (43.0 lb)

INSTALLING THE SPEAKER

When installing the speaker on the floor, attach the rubber spacers to the

underside of the speaker to provide support. Affix the rubber spacers firmly

when you attach them.

When installing the speaker on a wall or ceiling, use the included brackets

or optional U-bracket UB-DXR8. Ensure that the wall/ceiling is sufficiently

strong.

This package does not include the mounting hardware to install the

included brackets/safety wire or the UB-DXR8. If you are not sure what

materials are required for installation, consult a specialist.

An installed speaker is shown below. Install the bracket as shown.

WARNING

• Do not use the included brackets for ceiling installation.

• Do not use the UB-DXR8 for wall installation.

Pre-installation (Preparation of the cable)

Use stranded wire for cables attached to the Euroblock connector. Strip

their insulation as shown in the figure and connect them.

NOTE

Do not plate stranded wires by solder. Doing so will cause the wire to break.

Connect the cable from the amplifier to the “INPUT” socket, and the cable

being connected to other speakers to the “SATELLITE SPEAKERS”

socket.

A signal input to CH1 of INPUT is output from ST1 of SATELLITE

SPEAKERS, and signal input to CH2 of INPUT is output from ST2 of

SATELLITE SPEAKERS.

For VXS10ST/VXS10STW, connect the included 5-pin Euroblock

connector as shown below and set the appropriate wattage when using

100 V/70 V line.

NOTE

No setting should be made for 100 V line, as shown in the far left illustration.

1Remove the Euroblock connector from the speaker.

Wall installation

(using included brackets)

Ceiling installation

(using optional bracket

UB-DXR8)

1CONNECT THE WIRING TO THE CONNECTOR

100V/×

70V/200W

100V/200W

70V/100W

100V/100W

70V/50W

100V/50W

70V/25W

About 7 mm (0.3 in.)

SATELLITE SPEAKERS

VXS10S/VXS10SW VXS10ST/VXS10STW

INPUT

TRANSFORMER

SETTINGS

2After loosening the terminal screws of the Euroblock connector with a

flat-blade screwdriver, insert the cable into each terminal and tighten

the screws. Make sure that cables cannot be pulled out.

NOTE

Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).

3(VXS10ST/VXS10STW only) Plug the 5-pin Euroblock connector into

the TRANSFORMER SETTINGS socket.

1Place the bracket base on the wall and

mark the position for screws/bolts. The

diameter of seven holes for screw/bolt

(not included) is ø6.5 mm.

2Make holes in the wall for the bolts, as

required, and feed the bolts through

the holes.

3Affix the bracket base on the wall. The

narrow edge of the bracket base

should be oriented downward.

4Attach the mounting bracket to the speaker with the included screws

with captive washer.

The narrow edge of the mounting bracket should be oriented

downward.

5Attach the two rubber spacers to the bottom edge of the speaker.

Make sure the spacers are located near the outer edge; otherwise,

they will impede installation on the bracket base in the next step.

Affix the rubber spacers firmly when you attach them.

6Slide the speaker down onto the bracket base until it locks in place.

CAUTION

Be sure to perform this work with two or more people.

2INSTALL THE SPEAKER

Installing on the wall (using the included brackets)

Euroblock connector

Less than 3 mm (0.1 in.)

Bracket base

Mounting bracket

Captive washer screw

Rubber spacer

Lock

To detach the mounting bracket from the bracket base, release the

lock of the mounting bracket with a long flat-blade driver and lift the

speaker.

CAUTION

Be sure to perform this work with two or more people.

7Plug the Euroblock connectors into the

SATELLITE SPEAKERS and INPUT sockets.

To determine the appropriate size of the UB-DXR8, download the “U

BRACKET OWNER’S MANUAL” from the following manual library site.

http://www.yamaha.co.jp/manual/

1Assemble two L-shaped brackets into a U-shape using the M5 × 10

screws included with the UB-DXR8 as shown below. Peel off the

sheet from each rubber spacer (14 mm thickness; included with the

speaker), and attach the spacers to the inside of each bracket arm

aligning the holes so that the hexagon bolts can be inserted.

Affix the rubber spacers firmly when you attach them.

2Make sure that the width of the U bracket matches the speaker width.

3Affix the U bracket on the ceiling using appropriate mounting

hardware.

4Use the hexagon bolts, spring washers and flat washers included

with the speaker to attach the speaker to the UB-DXR8.

CAUTION

Be sure to perform this work with two or more people.

Installing on the ceiling (using the optional UB-DXR8)

M5 × 10

Rubber spacer

Hexagon bolt

Spring washer

Flat washer

5Plug the Euroblock connectors into the

SATELLITE SPEAKERS and INPUT sockets.

This section explains how to attach the included safety wire.

CAUTION

• Make sure to take measures to prevent the speaker from falling down in

the event of a installation failure.

• When installing the safety wire to the wall, install it higher than the wire’s

attachment point on the speaker, with as little slack as possible.

• If the safety wire is too short, prepare another wire appropriate for the

speaker weight and installation conditions. If the wire is too long, should

the speaker fall, the wire may snap as a result of too much strain.

1Pass the safety wire through the eyebolt on the rear of the speaker.

2Pass the bracket of the safety wire through the loop on the other end,

and pull tight up against the eyebolt.

3Affix the bracket of the safety wire to the wall.

3ATTACH THE SAFETY WIRE

Eyebolt

Owner’s Manual

Surface Mount Speaker

English

ZG14070

DIMENSIONS

VXS10S/VXS10SW

Bracket base Mounting bracket

VXS10ST/VXS10STW

: mm

Manual Development Department

Published 03/2015 YKZC-C0

Printed in Indonesia

Yamaha Pro Audio global web site

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Product specificaties

Merk:	Yamaha
Categorie:	Speaker
Model:	VXS10S
Kleur van het product:	Zwart
Materiaal:	MDF
Impedantie:	8 Ohm
Gemiddeld vermogen subwoofer:	100 W
Diameter driver subwoofer (imperiaal):	10 "
Frequentiebereik subwoofer:	45 - 250 Hz
Breedte van de subwoofer:	260 mm
Hoogte van de subwoofer:	500 mm
Diepte van de subwoofer:	389 mm
Gewicht subwoofer:	16500 g
Subwoofer sensitiviteit:	96 dB