Yamaha VXC4-VAW Handleiding

Yamaha Speaker VXC4-VAW

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha VXC4-VAW (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of

serious injury or even death from electrical shock, short-circuiting,

damages, fire or other hazards. These precautions include, but are not

limited to, the following:

• This device contains no user-serviceable parts. Do not open the device or

attempt to disassemble the internal parts or modify them in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as

water seeps into the device, have the device inspected by qualified Yamaha

service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of

physical injury to you or others, or damage to the device or other property.

These precautions include, but are not limited to, the following:

• Do not place the device in an unstable position where it might accidentally fall

over.

• Do not use the speaker’s handles for suspended installation. Doing so can

result in damage or injury.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Always consult qualified Yamaha service personnel if the device installation

requires construction work, and make sure to observe the following

precautions.

- Choose mounting hardware and an installation location that can support the

weight of the device.

- Avoid locations that are exposed to constant vibration.

- Use the required tools to install the device.

- Inspect the device periodically.

• Before connecting the device to other devices, turn off the power for all the

other devices. Before turning the power on or off for all devices, set all volume

levels to minimum.

• Use only speaker cables for connecting speakers to the speaker jacks. Use of

other types of cables may result in fire.

• Do not insert your fingers or hands in any gaps or openings on the device

(ports).

• Do not rest your weight on the device or place heavy objects on it.

• Do not operate the device if the sound is distorting. Prolonged use in this

condition could cause overheating and result in fire.

• Do not pull the cables connected.

• When choosing a power amplifier for use with this device, make sure that the

output power of the amplifier is lower than the power capacity of this device

(see “Specifications”).

Even if the output power of the amplifier is lower than the power capacity of

this device (program), use of excessive input signals resulting in clipping may

cause damage to the device.

Malfunction or fire may occur especially when the following sounds or noises

are generated:

- feedback, when using a microphone

- continuous and extreme volume sound from a musical instrument

- extreme continuous distorted sound

- noise caused by plugging/unplugging the cable while the amplifier is turned

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the device.

PRECAUTIONS

Do not open

Water warning

Location

Connections

Handling caution

NOTICE

To avoid the possibility of malfunction/damage to the product or damage to other

property, follow the notices below.

●Handling and maintenance

• Do not expose the device to excessive dust or vibration, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day), in

order to prevent the possibility of panel disfiguration, unstable operation, or

damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device, since this might

discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths.

• When turning on the AC power in your audio system, always turn on the

power amplifier LAST, to avoid speaker damage. When turning the power off,

the power amplifier should be turned off FIRST for the same reason.

• Be sure to observe the amplifier’s rated load impedance (see

“Specifications”), particularly when connecting speakers in parallel.

Connecting an impedance load outside the amplifier’s rated range can

damage the amplifier.

• When using a high-impedance speaker connection, make sure the audio

signal is passed through an 80 Hz or above high-pass filter before being input

to the speakers.

• When connecting the speakers with high impedance, be sure that the total

rated input capacity of the speakers does not exceed the output power of the

amplifier.

• Do not swing the speaker by its carrying band.

• Do not place the speaker face down with the grille attached, as deformation of

the grille may result.

• When placing the speaker face down, always place it on a flat and smooth

surface.

• Do not touch the speaker driver unit.

●Protective circuit

This speaker system has an internal protection circuit that shuts off the speaker

unit when an excessive input signal is applied. If the speaker unit emits no

sound, reduce the volume level of the amplifier immediately. The sound will

return automatically in several seconds.

●About this manual

• The illustrations as shown in this manual are for explanation only, and may

appear somewhat different from your device.

• The company names and product names in this manual are the trademarks or

registered trademarks of their respective companies.

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying

documents means that used electrical and electronic products

should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please

take them to applicable collection points, in accordance with your

national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save

valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from inappropriate

waste handling.

For more information about collection and recycling of old products, please contact

your local municipality, your waste disposal service or the point of sale where you

purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer

or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items,

please contact your local authorities or dealer and ask for the correct method of

disposal.

Supplied Items

Unpack the contents and confirm that all the following items are included.

* Speaker cable and safety wire are not supplied.

Specifications

The specifications data was measured in an anechoic chamber, according to EN 54-24.

Reference axis: Axis is on the center of grille surface and perpendicular to the grille surface.

Reference plane: Plane is on the grille surface and perpendicular to the reference axis.

Horizontal plane: Plane is containing the reference axis and perpendicular to the reference plane.

*1: Half-space (2π)

*2: Calculated based on power rating and sensitivity, exclusive of power compression.

*3: When connecting with low impedance.

*4: 30 mm or less for the Anti-Drop Tab.

The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual

may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since

specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

The dimensions are shown in “Technical Specifications”.

• Speaker × 2 • Grille × 2 • O-ring × 2

• Tile Rail × 4 • Screw (4 × 8) × 12 • Cutout Template × 1

• Terminal cover × 2 • Owner’s Manual (this manual) • Technical Specifications (English only)

Model VXC4-VA / VXC4-VAW

Type Full range with back can, acoustic suspension

Component 4" (10 cm) full range

Coverage angle (–6 dB)*1Horizontal: 180° (500 Hz), 180° (1 kHz), 160° (2 kHz), 85° (4 kHz)

Vertical: 180° (500 Hz), 180° (1 kHz), 160° (2 kHz), 85° (4 kHz)

Rated impedance 8 Ω (without transformer)

100 V line: 330 Ω (30 W), 670 Ω (15 W), 1.3 kΩ (7.5 W)

70 V line: 170 Ω (30 W), 330 Ω (15 W), 670 Ω (7.5 W), 1.3 kΩ (3.8 W)

Power rating NOISE 30 W

PGM 60 W

MAX 120 W

Sensitivity*187 dB (1 W, 1 m, 100 Hz to 10 kHz pink noise)

75 dB (1 W, 4 m, 100 Hz to 10 kHz pink noise)

Maximum SPL*2100 dB (30 W, 1 m, 100 Hz to 10 kHz pink noise at 30 W tap)

88 dB (30 W, 4 m, 100 Hz to 10 kHz pink noise at 30 W tap)

108 dB (120 W, 1 m, 100 Hz to 10 kHz pink noise at 8 Ω)

96 dB (120 W, 4 m, 100 Hz to 10 kHz pink noise at 8 Ω)

Frequency range (–10 dB)*1, *380 Hz – 20 kHz

Connector Ceramic terminal block (3 pin) × 1 (input: +/–, Earth)

Applicable wire size AWG 26–12 (4.0 mm2), wire outer diameter Ø6.5 – Ø12.5 mm

Transformer taps 70 V 30 W, 15 W, 7.5 W, 3.8 W

100 V 30 W, 15 W, 7.5 W

Overload protection Full-range power limiting to protect network and transducers

Magnetically shielded No

Dust and water resistant IP32 (EN54-24 Enclosure protection rating. Type A: IP21C)

Enclosure Back can Steel (t=1 mm), electrodeposition coating, black

Baffle ABS (UL94-5VB), black

Grille Metal grille Powder coated perforated steel (t=0.6 mm), aperture ratio: 51%

Trim ABS

Outer color (grille) VXC4-VA Black (approximate value: Munsell N3)

VXC4-VAW White (approximate value: Munsell 9.3)

Dimensions (with grille) Ø225 × 232 D mm (Ø8 7/8" × 9 3/16" D)

Net weight (with grille, 1 piece) 2.6 kg (5.7 lbs)

Cutout size Ø186 mm (Ø7 5/16")

Required ceiling board thickness 5 mm – 35 mm*4

Packaging Packaged in pair

Standards Certified to the European Standard EN 54-24: 2008 0359-CPR-00405 Certified year: 14

Loudspeaker for voice alarm systems for fire detection and fire alarm systems

Environment type: A

Certified to the European Standard EN60849:1998

Sound systems for emergency purposes

Certified to the International Standard ISO 7240-24: 2010

Sound-system loudspeaker for fire detection and fire alarm systems

In compliance with the British Standard BS-5839-8: 2008 14.8

Connecting the Multiple Speakers

When installing the multiple speakers, connect them in parallel way.

CAUTION

When connecting with low impedance, take note of the combined

resistance.

Note

When connecting with high impedance, refer to “Better Sound for

Commercial Installations” (English only) of the Yamaha Pro Audio

web site, at the following URL.

http://www.yamahaproaudio.com/global/en/training_support/

better_sound/

Installing the Speakers

Install the speakers onto the ceiling with the supplied hardware.

Ensure that the strength of the ceiling rail is sufficiently strong.

Pre-installation (Preparation of the Cable)

Use stranded wire for cables attached to the ceramic terminal. Strip

their insulation as shown in the figure and connect them.

Note

Do not plate stranded wires by solder. Doing so will cause the wire to

break.

1.1 Put the supplied cutout template to the ceiling and draw a circle by

tracing it.

Make sure to use the cutout template so that hole is the correct

diameter.

Note

If you use a circular cutter, set the diameter with the cutout template.

1.2 Cut the hole by tracing the circle.

Be careful to prevent chips or powder entering your eyes while

cutting the hole.

2.1 Insert the two tile rails through the cut hole and place them on the

ceiling surface within your reach. Be sure that each tile rails are

oriented as shown below.

2.2 Insert the folded O-ring through the cut hole and open it in the ceiling.

2.3 Secure the O-ring and tile rails with supplied two screws through

either slot of both O-ring brackets.

1Cut Out a Hole in the Ceiling

2Install the Tile Rails and O-ring

From amplifier or

previous speakers

To subsequent

speakers

subsequent

speakers

Speaker

Power

amplifier * You can use this terminal to hook up an earth cable, as

necessary.

About 7 mm (0.3")

20141007

3.1 Pull the wiring from the amplifier through the cut hole.

3.2 Pass the cables through the cable gland attached to the terminal

cover.

If it is difficult to pass all the cables through a single cable gland, open

the hole in the terminal cover and attach a commercially available

cable gland.

Note

Prepare a cable gland of AVC part no. PGB 13.5-12B.

CAUTION

Use an appropriate tool for opening the hole. Otherwise, you may be

injured if you open the hole with your bare hands.

3.3 Loosen the terminal screws of the ceramic terminal with a flat-blade

screwdriver, insert the cables into each terminal and tighten the

screws. Pull on the cables to make sure they are tightly secured and

will not come loose.

Note

Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).

3.4 Close the terminal cover and tighten the screws.

3Connecting the Wiring to the Speakers

Cable gland

Terminal cover

* Use the Earth terminal as necessary.

Earth*

–

Less than 3 mm (0.1 in.)

3.5 Tighten the cap of the cable gland.

4.1 Attach the safety wire to the safety wire ring, and connect the wire to

an independent support point, such as a joist.

CAUTION

Always take measures to prevent the speaker falling down.

If the safety wire is too short, prepare another wire appropriate for the

speaker weight and installation conditions. If the wire is too long,

should the speaker fall, the wire may break as a result of too much

strain.

4.2 Push up the speaker slowly into the ceiling, taking care not to trap the

cable.

When all the Anti-Drop Tabs cross

over the O-ring, the speaker is held

temporarily.

To release the speaker from the

O-ring, press the Anti-Drop Tabs.

These are located above the U mark

near the edge of the baffle’s face.

4Fix the Speakers onto the Ceiling

Cap

Safety wire ring

Anti-Drop Tab

4.3 Turn the screwdriver a half turn counterclockwise to loosen the

attachment screw (located beside the U mark). This makes the

clamp easier to align in the channel.

4.4 Turn the screwdriver clockwise to tighten the attachment screw.

The first turn of the attachment screw aligns the clamp with the

channel. Further turns move the clamp down the channel to pull the

speaker up into the ceiling.

CAUTION

• Do not over-tighten the attachment screw. Otherwise, the

attachment screw and clamp will break.

• Do not turn any screws other than attachment screw (located

beside the U mark). Otherwise, the speaker may fall or

malfunction.

Select the line voltage/impedance (100V/70V/8Ω) and power tap for

100V/70V line distributed system, by rotating the tap selector switch

on the front side of the speaker with a flat-blade screwdriver.

CAUTION

• The “X” position should not be selected. The 8Ω position should be

selected for 8Ω audio systems only. If the setting is incorrect, it may

cause malfunction of the speaker and amplifier.

• Make sure the amplifier is switched off before operating the tap

selector switch.

Fit the grille to the baffle front and turn it clockwise.

CAUTION

The grille may fall down if it is attached inadequately. Attach it firmly.

The installation is complete.

5Set the Line Voltage/Impedance and Power

6Attach the Grille

Clamp

The illustration indicates the setting at 30 W for 100 V

line and 15 W for 70 V line.

Yamaha Pro Audio global web site

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Owner’s Manual

Ceiling Speaker

English

ZK27900

EN FR

La version française du Mode d'emploi se trouve au verso.

Product specificaties

Merk:	Yamaha
Categorie:	Speaker
Model:	VXC4-VAW
Kleur van het product:	Wit
Gewicht:	2600 g
Diepte:	232 mm
Type verpakking:	Doos
Connectiviteitstechnologie:	Bedraad
Diameter:	225 mm
Gemiddeld vermogen:	30 W
Aantal per verpakking:	2 stuk(s)
Aanbevolen gebruik:	Universeel
Impedantie:	8 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Plafond-montage
Aantal drivers:	1
Woofer:	Nee
Frequentiebereik:	80 - 20000 Hz
Gevoeligheid:	87 dB
Luidspreker soort:	1-weg
Speaker omsluiting:	Gesloten
Versterker:	Nee
Diameter mid-range driver:	4 "
RMS-vermogen luidsprekers:	130 W
Tweeter:	Nee
Geluidsdruk niveau (max):	108 dB