Yamaha VXC3FW Handleiding

Yamaha Speaker VXC3FW

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha VXC3FW (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of

serious injury or even death from electrical shock, short-circuiting,

damages, fire or other hazards. These precautions include, but are not

limited to, the following:

• This device contains no user-serviceable parts. Do not open the device or

attempt to disassemble the internal parts or modify them in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions. If any liquid such as water seeps into the device, turn off the power

of the amplifier immediately and unplug the power cord from the AC outlet.

Then have the device inspected or repaired by qualified Yamaha service

personnel.

• Do not use burning items near the device. It may cause a fire.

• When one of the following problems occur, immediately turn off the power of

the amplifier.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the device.

- There are cracks or damage on the device.

Then have the device inspected by Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of

physical injury to you or others, or damage to the device or other property.

These precautions include, but are not limited to, the following:

• Do not place the device in an unstable position where it might accidentally fall

over and cause injuries.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Always consult a professional constructor if the device installation requires

construction work, and make sure to observe the following precautions.

- Choose mounting hardware and an installation location that can support the

weight of the device.

- Avoid locations that are exposed to constant vibration.

- Use the required tools to install the device.

- Inspect the device periodically.

• Before connecting the device to a power amplifier, turn off the power for all

devices. Before turning the power on or off for all devices, set all volume

levels to minimum. It may result in electric shock, hearing loss, or equipment

damage.

• Use only speaker cables for connecting speakers to the speaker jacks. Use of

other types of cables may result in fire.

PRECAUTIONS

Do not open

Water warning

Fire warning

If you notice any abnormality

Location

Connections

• Do not insert your fingers or hands in the moving part of the release lever/

bass reflex ports.

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (vents, disc slots, ports, etc.) If this happens,

turn off the power of the amplifier immediately and unplug the power cord

from the AC outlet. Then have the device inspected by qualified Yamaha

service personnel.

• Do not use the speakers for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• Do not operate the device if the sound is distorting. Prolonged use in this

condition could cause overheating and result in fire.

• When choosing a power amplifier for use with this device, make sure that the

output power of the amplifier is lower than the power capacity of this device

(see General Specifications). If the output power is higher than the power

capacity, malfunction or fire may occur.

• Do not input excessively loud signals that may result in clipping in the

amplifier or cause the following:

- Feedback, when using a microphone

- Continuous and extremely loud sound from a musical instrument, etc.

- Continuous and excessive loud distorted sound

- Noise caused by plugging/unplugging the cable while the amplifier is turned

Even if the output power of the amplifier is lower than the power capacity of this

device (program), damage to the device, malfunction or fire may occur.

NOTICE

To avoid the possibility of malfunction/damage to the product or damage to other

property, follow the notices below.

●Handling and maintenance

• When using a high-impedance speaker connection, make sure the audio

signal is passed through an 80 Hz or above high-pass filter before being input

to the speakers.

• Do not expose the device to excessive dust or vibration, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day), in

order to prevent the possibility of panel disfiguration, unstable operation, or

damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device, since this might

discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic changes in

ambient temperature-when the device is moved from one location to another,

or air conditioning is turned on or off, for example. Using the device while

condensation is present can cause damage. If there is reason to believe that

condensation might have occurred, leave the device for several hours without

turning on power until the condensation has completely dried out.

• Be sure to observe the amplifier’s rated load impedance (see General

Specifications), particularly when connecting speakers in parallel. Connecting

an impedance load outside the amplifier’s rated range can damage the

amplifier.

• Protection Circuit

This speaker system has an internal protection circuit that shuts off the

speaker unit when an excessive input signal is applied.

If the speaker unit emits no sound, reduce the volume level of the amplifier

immediately. The sound will return automatically in several seconds.

• Air blowing out of the bass reflex ports is normal, and often occurs when the

speaker is handling program material with heavy bass content.

• Do not swing the speaker by its carrying band.

• Do not place the speaker face down with the grille attached, as deformation of

the grille may result.

• When placing the speaker face down, always place it on a flat surface.

• Do not touch the speaker driver unit.

●About this manual

• The illustrations as shown in this manual are for instructional purposes only.

• The company names and product names in this manual are the trademarks or

registered trademarks of their respective companies.

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the device.

Handling caution

Unpacking

Unpack the contents and confirm that all the following items are included.

* The speaker cable and safety wire are not included.

General Specifications

*1: Half-space (2π)

*2: Calculated based on power rating and sensitivity, exclusive of power compression.

The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual may

not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since specifications,

equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

The dimensions are shown in “Technical Specifications”.

• Speaker × 2 • O-ring × 2 • Cutout Template × 1

• Grille × 2 • Tile Rail × 4 • Owner’s Manual (this manual)

• Euroblock Plug (4-pin, 5.08 mm pitch) × 2 • Screw × 4 • Technical Specifications (English only)

• Terminal Cover (with 3 screws) × 2

VXC5F/VXC5FW VXC3F/VXC3FW

Type Full range, Bass reflex

Component 4.5” (11.5 cm) Full range unit 3.5” (9 cm) Full range unit

Coverage angle (1 kHz – 4 kHz on average) *1130° conical 140° conical

Nominal impedance 8 Ω

Power rating NOISE 40 W 20 W

PGM 80 W 40 W

MAX 160 W 80 W

Sensitivity (1W, 1m) *189 dB SPL 87 dB SPL

Maximum SPL (Calculated, 1m) *2111 dB SPL 106 dB SPL

Frequency range (-10 dB) *160 Hz – 20 kHz 71 Hz – 20 kHz

Connector Euroblock (4 pin) × 1 (input: +/-, loop-thru: +/-)

Max. wire size 12 AWG

Transformer taps 70 V 30 W, 15 W, 7.5 W, 3.8 W 15 W, 7.5 W, 3.8 W, 1.9 W

100 V 30 W, 15 W, 7.5 W 15 W, 7.5 W, 3.8 W

Overload protection Full-range power limiting to protect network and transducers

Magnetically shielded No

Enclosure Shape Round

Cabinet material ABS V-0, 3.5 mm, black

Baffle material ABS V-0, 5 mm, black

Grille Material Powder coated perforated steel (t=0.6 mm)

Trim Ring: ABS V-0

Aperture ratio: 46%

Finish VXC5F/VXC3F : Black painting (approximate value: Munsell N3)

VXC5FW/VXC3FW : White painting (approximate value: Munsell 9.3)

Dimensions (Including grille) Ø324 × 143D mm (Ø12-13/16" × D 5-11/16") Ø285 × 112D mm (Ø11-1/4" × D 4-7/16")

Net weight (Including grille) 3.1 kg (6.8 lbs) 2.5 kg (5.5 lbs)

Cutout size Ø285 mm (Ø11-1/4") Ø247 mm (Ø9-3/4")

Required ceiling board thickness 5 mm – 37 mm

Conduit tube Ø15.4 mm – Ø21.3 mm

Packaging Packaged in pair

Connecting the Cable

CAUTION

• When connecting with low impedance, take note of the total impedance.

• When connecting with high impedance, the total input wattages of the connected speakers should lie within the margin of the rated input of the power

amplifier. For more information, refer to the description concerning high impedance connection at the following URL.

Yamaha Pro Audio site “Better Sound for Commercial Installations”: http://www.yamahaproaudio.com/global/en/training_support/better_sound/

Using Loop-Through Terminals

For this method, cables are connected from terminals 1 and 4 to the

subsequent speaker. Cables with a thickness up to AWG 12 can be used. If

the Euroblock plug is disconnected from a speaker, all subsequent speakers

will not work. This can be useful to identify which speaker has a problem.

Paralleling Input Terminals

For this method, cables are connected to terminals 2 and 3 of each

speaker. Connect two cables to one terminal. Cables with a thickness up

to AWG 17 can be used. Since the cables are connected via Euroblock

plugs, subsequent speakers can work properly.

From amplifier or

previous speakers To subsequent

speakers

subsequent

speakers

Euroblock

plug

Power

amplifier

Speaker

From amplifier or

previous speakers

To subsequent

speakers

Power

amplifier

Speaker

Euroblock

plug

subsequent

speakers

Installing the Speakers

Install the speakers onto the ceiling with the supplied hardware. Ensure that

the strength of the ceiling rail is sufficiently strong.

Illustrations in this manual are for the VXC3F. The installation method is the

same for other models.

CAUTION

When attaching the speakers, turn off the power amplifier.

Pre-installation (Preparation of the Cable)

• Use stranded wire for cables attached to the Euroblock plug. Strip their

insulation as shown in the figure and connect them.

Note

Do not plate stranded wires by solder. Doing so will cause the wire to

break.

• Make sure that the release lever of the baffle front is in the position as

shown in the figure below.

1Put the supplied cutout template to the ceiling and draw a circle by

tracing it.

Make sure to use the cutout template so that hole is the correct

diameter.

Note

If you use a circular cutter, set the diameter with the cutout template.

2Cut the hole by tracing the circle.

Be careful to prevent chips or powder entering your eyes while

cutting the hole.

1Insert the two tile rails through the cut hole and place them on the

ceiling surface within your reach. Be sure that each tile rails are

oriented as shown below.

2Insert the folded O-ring through the cut hole and open it in the ceiling.

3Secure the O-ring and tile rails with supplied two screws through

either slot of both O-ring brackets.

1Cut Out a Hole in the Ceiling

2Install the Tile Rails and O-ring

About 7 mm (0.3 in.)

Maximum thickness of the cable 12 AWG

Release lever

O-ring

Tile rail

1Pull the wiring from the amplifier through the cut hole of the ceiling.

2Pass the cable through the terminal cover.

3After loosening the terminal screws of the Euroblock plug with a flat-

blade screwdriver, insert the cable into each terminal and tighten the

screws. For the connection, refer to “Connecting the Cable”. Make

sure that cables cannot be pulled out.

Note

Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).

4Plug the connected Euroblock plug into the socket in the speaker.

5Tighten the screw and then attach the terminal cover.

3Connect the Wiring to the Connector

Euroblock plug

Terminal screw

Loosen

Flat-blade

screwdriver

Tighten

Less than 3 mm (0.1 in.)

1Take care not to trap the cable, carrying band, or safety wire while

slowly pushing the speaker up into the ceiling.

Make sure the release lever is in the position of the figure below. If it

is set to the position of the figure, when all the Anti-Drop tabs cross

over the O-ring, the speaker is held temporarily.

2While slightly lifting up the speaker, turn the screwdriver clockwise to

tighten the attachment screw.

The first turn of the attachment screw opens the clamp. Further turns

move the clamp down the channel to pull the speaker up into the

ceiling.

Note

When the clamp is difficult to open, turning the screwdriver halfway

counterclockwise once will make it easier to open the clamp.

CAUTION

• Do not over-tighten the attachment screw. Otherwise, the

attachment screw and clamp will break.

• Do not turn any screws other than attachment screw. Otherwise,

the speaker may fall or malfunction.

4Fix the Speakers onto the Ceiling

For safety, use the screw hole on the speaker (M5 × 12 mm) and

connect the wire to an independent support point such as a joist.

Example of the connection using an eye bolt

CAUTION

Always take measures to prevent the speaker from falling down.

Use a safety wire of appropriate length. Should the speaker fall and the

wire is too long, the wire may snap due to excess strain.

Safety wire

Eye bolt

Screw hole

(M5 × 12 mm)

Anti-Drop tab Carrying band

Release lever Anti-Drop tab

Fixing screw

Clamp

Select the line voltage/impedance (100 V/70 V/8Ω) and power tap for

100 V/70 V line distributed system, by rotating the tap selector switch on

the front side of the speaker with a flat-blade screwdriver.

CAUTION

• The “X” position should not be selected. The 8Ω position should be

selected for 8Ω audio systems only. If the setting is incorrect, it may

cause malfunction of the speaker and amplifier.

• Make sure the amplifier is switched off before operating the tap selector

switch.

Attach the string to the speaker as shown in the figure, then fit the grille to

the magnets (6 places) on the baffle front.

CAUTION

The grille may fall down if it is attached inadequately. Attach it firmly.

Removing from the Ceiling

1Loosen the fixing screw by turning the screw counterclockwise.

Loosen the screw and the clamp goes up, and as it reaches the top,

the clamp closes as shown in figure below.

2While slightly lifting up the speaker, secure it by moving the release

lever of the baffle front to the direction of the arrow as shown in the

figure.

3Remove the safety wire from the speaker that is detached from the

ceiling.

5Set the Line Voltage/Impedance and Power

6Attach the Grille

Clamp

Illustration indicates the setting at 15 W for 100 V

line and 7.5 W for 70 V line.

Magnet

Correctly attachedIncorrectly attached

Yamaha Pro Audio global web site:

http://www.yamahaproaudio.com/

Yamaha Manual Library:

http://www.yamaha.co.jp/manual/

Owner’s Manual

SPEAKER SYSTEM

English

ZP40630

EN DE

Auf der Rückseite befindet sich die deutsche Version der Bedienungsanleitung.

Product specificaties

Merk:	Yamaha
Categorie:	Speaker
Model:	VXC3FW
Kleur van het product:	Wit
Gewicht:	2500 g
Breedte:	- mm
Diepte:	112 mm
Hoogte:	- mm
Connectiviteitstechnologie:	Bedraad
Diameter:	285 mm
Gemiddeld vermogen:	20 W
Impedantie:	8 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Aantal drivers:	1
Peak Music Power Output (PMPO):	80 W
Frequentiebereik:	71 - 20000 Hz
Gevoeligheid:	87 dB
Luidspreker soort:	Volledig bereik
Diameter mid-range driver:	3.5 "
Aantal Euroblock-ingangsconnectoren:	1