Yamaha NS-AW992 Handleiding

Yamaha Speaker NS-AW992

Lees hieronder de 📖 handleiding in het Nederlandse voor Yamaha NS-AW992 (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

1 2

× 4

A B

10 mm

(3/8˝)

–

NS-AW992 (R) NS-AW992 (L)

– + – +

158

208 233

169.2

105

40.9

127

ø20

6×11

5.5×10

117

ø5.5

69.5

ø54

ø6

388

× 2

NS-AW992

OUTDOOR SPEAKER

ENCEINTE D’EXTERIEUR

UCG

Printed in Indonesia WT55050

Speaker output terminals

Bornes de sortie enceinte

Lautsprecherausgangs-

klemmen

Amplifier or receiver

Amplificateur ou récepteur

Verstärker oder Receiver [mm]

CONSUMER PRECAUTIONS

Read these precautions carefully before setting up your NS-AW992

speakers.

• When mounting these speakers, be sure to work with two or more

persons for safety.

• When installing these speakers outdoors, try to minimize their

exposure to rain and snow by mounting the speaker in corners or

under eaves.

• Since these speakers are to be wall / ceiling mounted, it is essential

that they are firmly secured. Be sure to consult a reliable source

about the best type of fastener for your particular wall / ceiling’s

construction.

• Do not attach them to thin plywood or soft wall / ceiling surface

materials as the screws may tear free, causing the speakers to fall

and be damaged, or result in personal injury.

• Do not fasten the speakers to wall / ceiling with nails, adhesives, or

other unsafe hardware. Long-term use and vibrations may cause

them to pull free.

• Do not place the speakers where they are liable to be knocked over

or struck by falling objects. Stable placement will also ensure better

sound performance.

• When changing the angle of the speakers, be sure to adjust the

angle after loosening the knob on the both sides. The speakers may

be damaged by excessive power.

• Lower the power amplifier / receiver volume control before changing

input sources. Always turn the amplifier / receiver unit off when

installing or removing input cables.

• Anytime you note distortion, reduce the volume control on your

power amplifier / receiver to a lower setting. Never allow your power

amplifier to be driven into “clipping”.

• Do not attempt to modify or fix the speakers. Contact qualified

Yamaha service personnel when any service is needed. The cabinet

should never be opened for any reasons.

• Do not attempt to clean the speakers with chemical solvents as this

might damage the finish. To clean wipe with a dry, soft cloth.

• Secure placement or installation is the owner’s responsibility.

Yamaha shall not be liable for any accident caused by improper

placement or installation of speakers.

After unpacking, please inspect contents to confirm all the following

items are contained.

ASpeaker × 2

BBracket × 2

CKnob × 4

To wall / ceiling mount the speakers, use the included bracket.

AUsing the bracket as a template mark the locations (four points) of

the key hole slots on the mounting area.

BUsing appropriate hardware (not included) securely fasten the

bracket to the wall / ceiling.

CPosition the speaker in the bracket and secure the speaker by

using the two knobs included.

DRotate the YAMAHA emblem according to the position of the

speaker.

When using the brackets to mount the speakers on a wall / ceiling,

please use safety wire (not included) between the speaker and the

bracket to prevent the speaker from falling. Please use safety wire

which withstand load

is 3.7 kg (8.2 lbs.) or

more.

Fix the safety wire with

M5 screw (inch screw: No. 10-32) by using the screw hole [diameter: 5

mm (1/4″), depth: 15 mm (5/8″)] at the rear of the speakers. For safety,

please confirm that installed screw is in the screw hole more than 10

mm (3/8″).

Before making connections, make sure that the amplifier / receiver is

switched off.

CONNECTIONS

• Connect the input terminals at the rear of the speakers to the

speaker output terminals of the amplifier / receiver with the speaker

cables (not included).

• Connect each speaker making sure not to reverse the polarity

“+” (red), “–” (black). If the speaker is connected with reversed

polarity, the sound will be unnatural and lack bass.

HOW TO CONNECT

ARemove approximately 10 mm (3/8″) of insulation from the end of

each speaker cable and twist the exposed wires of the cable

together to prevent short circuits.

BUnscrew the terminal knob.

CInsert one bare wire into the hole in the side of each terminal.

DTighten the terminal knob to secure the wire.

SPECIFICATIONS (For single speaker)

* Specifications subject to change without notice due to product

improvements.

English

1UNPACKING

2MOUNTING THE SPEAKERS

If speaker cable (not included) is being fed from a hole in the wall /

ceiling behind the bracket, pull this speaker cable through the hole in

the bracket before mounting the bracket [figure - ].

2 a

3CONNECTING YOUR AMPLIFIER / RECEIVER

Note: Do not let the bare speaker wires touch each other as this could

damage the speaker or amplifier / receiver, or both.

Type 2-Way Acoustic Suspension

Driver Tweeter 2.5 cm (1″) soft dome type

Woofer 20 cm (8″) cone type

Frequency response 50 Hz to 20 kHz (–10 dB)

Impedance 6 ohms

Nominal input 60 W

Maximum input 180 W

Sensitivity 90 dB / 2.83 V, 1 m

Crossover frequency 6 kHz

Dimension (W × H × D)

(excluding bracket and

knobs)

233 × 388 × 208 mm

(9-1/8″ × 15-1/4″ × 8-1/4″)

Weight (including bracket

and knobs) 4.15 kg (9.1 lbs.)

IP rating IPX3

Materials of the main

parts

Enclosure: HIPS

Punching grill: Aluminum (powder coating)

Bracket: Steel [t = 1.6 mm (1/16″)] (powder

coating)

Movable angle 10 degree pitch

Warranty policy for European Economic Area (EEA) and

Switzerland, Australia customer

In the unlikely event that your Yamaha product needs guarantee service,

please contact the dealer from whom it was purchased. If you experience

any difficulty, please contact Yamaha representative office in your country.

You can find full details on our website

EEA and Switzerland: (http://www.yamaha-hifi.com/ or http://

www.yamahauk.com/ for U.K. resident).

Australia: (http://www.yamahamusic.com.au/)

Warranty policy for U.S. and Canada customer

Your Yamaha product is covered by a limited warranty for two years from

the date of purchase. In the unlikely event of failure due to defective

materials or workmanship, Yamaha will repair or replace them at no

charge.

For full details, please see the included warranty card or visit our website.

U.S.: (http://www.yamaha.com/yec/), Canada: (http://www.yamaha.ca/)

Information for Users on Collection and Disposal of Old Equipment

This symbol specified in the Directives 2002/96/EC indicates

that used electrical and electronic products should not be

mixed with general household waste.

For proper treatment to avoid harmful effect on human health

and environment, please contact your local municipality, your

waste disposal service or the point of sale where you purchased the

items.

Product specificaties

Merk:	Yamaha
Categorie:	Speaker
Model:	NS-AW992
Kleur van het product:	Wit
Breedte:	233 mm
Diepte:	209 mm
Hoogte:	388 mm
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	60 W
Equalizer-instellingen:	Nee
Aanbevolen gebruik:	Universeel
Impedantie:	6 Ohm
Audio-uitgangskanalen:	2.0 kanalen
Speaker plaatsing:	Buiten
Aantal drivers:	1
Woofer:	Ja
Peak Music Power Output (PMPO):	180 W
Frequentiebereik:	50 - 20000 Hz
Gevoeligheid:	90 dB
Luidspreker soort:	2-weg
Versterker:	Nee
Diameter woofer:	200 mm
Diameter hogetonenluidspreker:	25 mm
Tweeter:	Ja