Whirlpool WSFP 4O23 PF X Handleiding

Whirlpool Vaatwassers WSFP 4O23 PF X

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool WSFP 4O23 PF X (19 pagina's) in de categorie Vaatwassers. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/19
EN
1
Before using the appliance carefully read Health and Safety guide.
APPLIANCE
PRODUCT DESCRIPTION
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please register your appliance on:
www.whirlpool.eu/register
1. Upper rack
2. Cutlery rack
3. Foldable aps
4. Upper rack height adjuster
5. Upper spray arm
6. Lower rack
7. Power Clean® support
8. Lower spray arm
9. Filter Assembly
10. Salt reservoir
11. Detergent and Rinse Aid dispensers
12. Rating plate
13. Control panel
6 7 8 9 10 12 13 141 2 3 4 5 1615 17 18 2019
h
11
1. ON-OFF button
2. PREVIOUS button
3. NEXT button
4. Tablet Detergent (All-in-one) button
5. Multizone button / Key Lock
6. Multizone indicator lights
7. Eco program indicator light
8. Start Delay indicator light
9. Display
10. Program number and remaining time indicator
INSTRUCTION FOR USE
CONTROL PANEL
11. Key Lock indicator light
12. Closed water tap indicator light
13. Rinse Aid rell indicator light
14. Salt rell indicator light
15. Tablet Detergent (All-in-one) indicator light
16. Sani Rinse button with indicator light
17. Turbo button with indicator light
18. Power Clean® button with indicator light
19. Start Delay button with indicator light
20. START/Pause button with indicator light
7
1
3
4
5
6
8
10
9
13
2
0000 000 00000
Service:
1112
2
FIRST TIME USE
SETTING MENU AND SALT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the reta-
ining elastic elements from the upper rack.
SETTING MENU
1. Switch on the appliance by pressing the button.ON/OFF
2. Switch o the appliance by pressing the button.ON/OFF
3. Hold down START/Pause button for 5 seconds, until you hear a
beep.
4. The display shows the rst available setting (letter „A”), followed by
its value (for example: 3).
5. Press PREVIOUS/NEXT button to scroll the list of the available
settings and to see their value (see the below table), then press
START/Pause if you want to change the value of the displayed set-
ting: its value will start blinking.
6. Use PREVIOUS/NEXT button to change the blinking value of the
selected settings, then press START/Pause to save the new value:
it will stop blinking.
7. To change another settings repeat steps 5-6.
8. To exit settings menu - press button. ON/OFF
LETTER SETTING VALUES
(Default - in bold)
Water Hardness Level
(see setting the water hardness
and “water hardness table”)
1 | 2 | | 4 | 53
Rinse Aid Level
(see ADJUSTING THE DOSAGE OF
RINSE AID”)
1 | 2 | 3 | 4 | 5
Start Program
To set the cycle to show at switch
on of the appliance.
“E”= Eco, “L= Last cycle run
E | L
Brightness Level
To adjust the brightness
level of the display.
“Lo=Low, “Hi”= High
Lo | Hi
Sound Level
To adjust the volume of the sounds.
“OF” = sounds o, “Lo = low volume,
“Hi” = high volume.
OF | Lo | Hi
Factory Settings
To restore to the factory default all
the values of the settings included
in the settings menu. After the
activation of this setting (ON), the
machine switches OFF and restores
the factory settings.
“On = On, “OF” = O
On | OF
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
It is important that the salt reservoir be never empty.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and should be lled when the SALT REFILL
indicator light in the control panel is lit.
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. -Only the rst time you do this: ll the salt re
servoir with water.
3. Position the funnel (see gure) and ll the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
As soon as this procedure is complete, run a program without loading.
The “Pre-Wash” program alone is not sucient.
Residual saline solution or grains of salt can lead to corrosion, irrepara-
bly damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such circu-
mstances.
After the salt has been poured into the machine, the SALT REFILL in-
dicator light switches o.
Only use salt that has been specically designed for dishwashers.
If the salt container is not lled, the water softener and the he-
ating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is “3” for average water hardness.
To change, follow instructions in section “SETTING MENU.
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 17 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
EN
3
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should A
be lled when the in the control RINSE AID REFILL indicator light
panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Carefully introduce the rinse aid as far as the maximum (110 ml)
reference notch of the lling space - avoid spilling it. If this happens,
clean the spill immediately with a dry cloth .
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can ad-
just the quantity of rinse aid used.
To change, follow instructions in section “SETTING MENU.
If the rinse aid level is set to 1, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is 5”.
If you see bluish streaks on the dishes, set a low number (2-3).
If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
A
B
FIRST TIME USE
RINSE AID AND DETERGENT
FILLING THE DETERGENT DISPENSER
Only use detergent which has been specically designed for
dishwashers.
To achieve the best washing and drying results, the combined use
of detergent, rinse aid liquid and rened salt is required.
We recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount
of detergent being used.
Exceeding the stated amount does not result in a more eective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of normal-
ly soiled items, use approximately either 25g (powder detergent)
or 25ml (liquid detergent) and additional tea spoon of detergent
directly inside the tub. If tablets are used, one tablet will be eno-
ugh.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher, reduce the amount
of detergent used accordingly (minimum 20 g/ml) e.g. skip the
powder/gel putted inside the tub.
To open the detergent dispenser press button A. Introduce the
detergent into the dry dispenser B only. Place the amount of
detergent for pre-washing directly inside the tub.
1. When measuring out the detergent
refer to the mentioned earlier infor-
mation to add the proper quantity..
Inside the dispenser there are B
indications to help the detergent
dosing.
2. Remove detergent residues from
the edges of the dispenser and clo-
se the cover until it clicks.
3. Close the lid of the detergent
dispenser by pulling it up until the
closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program.
If all-in-one detergents are used, we recommend using the TABLET
DETERGENT button, because it adjusts the program so that the best
washing and drying results are always achieved.
If you are using a all-in-one detergents, we recommend that you add
salt in any case, especially if the water is hard or very hard (follow the
instructions given on the packaging).
A
B


Product specificaties

Merk: Whirlpool
Categorie: Vaatwassers
Model: WSFP 4O23 PF X

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool WSFP 4O23 PF X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Vaatwassers Whirlpool

Handleiding Vaatwassers

Nieuwste handleidingen voor Vaatwassers