Whirlpool W10606694A Handleiding

Whirlpool Wasdroger W10606694A

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool W10606694A (28 pagina's) in de categorie Wasdroger. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28
W10740674A
Installation Instructions
for W10606694 L.P. (Propane and Butane)
Gas Conversion Kit
Parts included in Kit:
1 Instruction Sheet
1 Blocking Pin
1 Orice, Burner-Butane No. .049
1 Orice, Burner-Propane No. 55
1 Label, Rating Plate Conversion (English)
1 Label, Rating Plate Conversion (French)
1 Label, Conversion Record (English)
1 Label, Conversion Record (French)
1 Label, Burner Baseplate (English/French)
Converting 20,000 BTU/hr Gas Burners from Natural Gas
to Liqueed Petroleum (Bottled Gas)
NOTE: A qualied service technician is any person or
representative of a company who is experienced or trained
in servicing gas equipment and is familiar with necessary
precautions.
IMPORTANT: The LP Conversion Kit you received is an
approved kit for converting your gas dryer from natural to LP
propane or butane gas. The kit number shown on the Burner
Data Label located on the Burner Base may not match the kit
you receive due to kit consolidation.
NOTE: Read these instructions before proceeding.
Canada Only
THIS CONVERSION KIT SHALL BE CARRIED OUT IN
ACCORDANCE WITH THE REQUIREMENTS OF THE
PROVINCIAL AUTHORITIES HAVING JURISDICTION AND
IN ACCORDANCE WITH THE REQUIREMENTS OF THE
CAN-B49.1 AND CAN1-B149.2 INSTALLATION CODE.
Warning: This conversion kit shall be installed by a qualied
service agency in accordance with the manufacturer’s
instructions and all applicable codes and requirements of
the authority having jurisdiction. The information in these
instructions must be followed to minimize the risk of re or
explosion or to prevent property damage, personal injury,
or death. The qualied service agency is responsible for the
proper installation of this kit. The installation is not proper
and complete until the operation of the converted appliance
is checked as specied in the manufacturer’s instructions
supplied with this kit.
This dryer has been manufactured for use with Natural Gas.
Installation of this conversion kit converts the dryer for use
with L.P. gas with supply pressure between 8" (203 mm) and
13" (330 mm) water column. If this dryer is converted for use
with L.P. gas by means of this kit, the input rating will be 20,000
BTU’s per hour, for altitudes up to 10,000 feet (3,048 m). For
installations above 2,000 feet (610 m), contact a qualied
service agency for derating instructions.
Preparing for Kit Installation
READ THOROUGHLY AND FOLLOW STEPS
1. Unplug dryer or disconnect power.
2. Turn off gas supply using the shut-off valve that supplies
the dryer.
3. Fill out information on the appropriate Conversion Record
Label (English or French) and apply in a conspicuous
location adjacent to model and serial tag located in the
door well. Go to Section 1, 2, or 3, depending on model.
Tools and Accessories required:
1/4" Socket and Ratchet Wrench
1/4" Nut Driver
5/16" Nut Driver
Phillips-Head Screwdriver
T-20 Torx®-head Screwdriver†
Pliers or Flat-Head Screwdriver
†® Torx and T-20 are registered trademarks of Acument Intellectual
Properties, LLC.
Disassembling the Dryer
Section
Cabinet
Width
Console
Location
Front Panel
Type
Rated
Capacity
(cubic feet)
Page
1 29" Rear Full 8.8+ 2
2 27" Front Full 7 to 7.5 4
3 29" Rear Full 7 to 7.6 8
4 27" Rear Toe Panel 7 to 7.5 9
2
Disassembling the Dryer
SECTION 1 – 8.8+ CUBIC FOOT MODELS WITH 29" CABINET,
FULL FRONT PANEL, AND REAR CONSOLE
To gain access to inside of dryer:
1. Remove console rear plate and rear shelf plate by
removing a total of eight (8) screws. See Figure 1.
2. Remove two (2) screws from the rear of the top.
See . This will allow the top to be slid rearwardFigure 2 .
3. Disconnect the door switch connector located in the top
left front corner of the dryer. See Figure 3.
4. Remove the front panel and door assembly by removing
a total of eleven (11) screws: Four (4) ¼" hex-head screws
along the bottom front, three (3) Phillips-head screws around
the door opening, and four (4) T-20 Torx-head screws on
the top front panel bracket. See . Once screws are Figure 4
removed, close the door and lift up the front panel and door
assembly to remove.
(3) SCREWS
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
5. Disconnect the drum light connector located in the top left
front corner of the dryer. See . Figure 5
FIGURE 5
(5) SCREWS CONSOLE
REAR
PLATE
REAR
SHELF
PLATE
(2) SCREWS
DOOR SWITCH
CONNECTOR
(3) SCREWS
(4) SCREWS
FRONT
PANEL
DRUM LIGHT
CONNECTOR
TOP
(4) SCREWS
3
6. Disconnect moisture strip connector located in lower right
front corner of the dryer. See Figure 6.
7. Remove the two (2) lower lint duct screws. See . Figure 6
8. Remove the four (4) screws from the two side edges of the
front bulkhead. See .Figure 7
9. Remove the front bulkhead and lint duct assembly by lifting
it off the two (2) front hooks (see ) and then lowering Figure 8
it to clear the drum support rollers from the drum front.
NOTE: Lift up on front of drum to help lift off of rollers on front
bulkhead.
NOTE: Since the drum belt is still in tension, it will pull the drum
down as you remove the front bulkhead and lint duct assembly.
10. Remove the drum belt tension by reaching into dryer
just under the drum to back side of drive motor. Grasp idler
pulley and lift up to relieve tension from belt and remove belt
from motor pulley and lower the idler slowly. See .Figure 9
FIGURE 6
FIGURE 7
FIGURE 8
FIGURE 9
LINT DUCT
(2) SCREWS
MOISTURE
STRIP
CONNECTOR
(4) SCREWS
FRONT
BULKHEAD
(2) BULKHEAD
HOOKS (ONE ON
EACH SIDE)
IDLER
PULLEY
MOTOR
PULLEY
DRUM
BELT


Product specificaties

Merk: Whirlpool
Categorie: Wasdroger
Model: W10606694A

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool W10606694A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wasdroger Whirlpool

Handleiding Wasdroger

Nieuwste handleidingen voor Wasdroger