Whirlpool TDLR 55140S EU Handleiding

Whirlpool Wasmachine TDLR 55140S EU

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool TDLR 55140S EU (32 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/32

1 Programme selector

2 “Start/Pause“ button

3 “Reset/Drain“ button

4 “Start delay“ button

5 Child lock combination

6 “Spin“ button

7 Time

8 Washing phase

INDICATORS

Lid open

Failure: Call Service

Failure: Water lter clogged

Failure: No water

In the event of any failure, refer to the

“TROUBLESHOOTING“ section

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance,

please register your product on

www.whirlpool.eu/register

CONTROL PANEL

PROGRAMME CHART

PRODUCT DESCRIPTION

1. Lid handle

2. Lid

3. Control panel

4. Detergent dispenser

5. Drum

6. Water lter - behind the cover

7. Mobility lever (depending on model)

8. Adjustable feet (x2)

DETERGENT DISPENSER

Main wash compartment

Detergent for the main wash, stain remover or

water softener.

Prewash compartment

Detergent for the prewash.

Softener compartment

Fabric softener. Liquid starch. Bleach.

Pour in softener, starch or bleach solution

only up to the “max” mark.

Release button 

Press to remove tray for cleaning.



the programmes, without options. The values given for programmes other than the eco 40-

60 programme are indicative only.

* After programme end and spinning with maximum selectable spin speed, in default

programme setting.

** The duration of the programme is shown on the display.

6th Sense - The sensor technology adapts water, energy and programme duration to your

wash load.

Eco 40-60 - Test wash cycle in compliance with 2019/2014 regulation. The most ecient

programme in terms of energy and water consumption for washing normally soiled cotton

laundry. Display only: Spin speed values shown on the display can slightly diers from the

values stated in the table

For all Test Institutes

Long wash cycle for cottons: set wash cycle Cotton with a temperature of 40°C.

Synthetic program along: set wash cycle Synthetics with a temperature of 40°C.

This data may dier in your home due to changing conditions in inlet water temperature,

water pressure etc. Approximate programme duration values refer to the default setting of

Quick guide

Before using the appliance carefully read the Safety Instruction.

Before using the machine, it is imperative that the transport bracket is removed.

For more detailed instructions on how to remove it, see the Installation Guide.

1 2 3 4 5

8 7

Max load 5,5 Kg

Power consumption in o-mode 0,11 W / in left-on mode 0,11 W Detergents and additives Recommended

detergent

Residual

dampness % *

Energy

consumption

kWh

Total water lt

Laundry

temperature °C

Programme

Temperatures Max.

Spin speed

(rpm)

Max

load

(kg)

Duration

(h : m)

Prewash Main

wash Softener

Powder Liquid

Setting Range

Mixed 40°C 40°C 1100 3,0 ** –     – – – –

40°C 40°C

1051 5,5 3:10 –     62 0,651 47 38

1051 2,75 2:30 –     62 0,421 37 34

1051 1,5 2:30 –     62 0,455 37 34

20°C 20°C 1100 5,5 3:10 –   –62 0,270 47 20

Colours 40°C 40°C 1000 4,0 **     – – – – –

Wool 20°C 20°C 1000 1,0 ** –   –– – – –

Spin – – 1100 5,5 ** – – – – – – – – –

Rinse + Spin – – 1100 5,5 ** – – – – – – – –

Delicates 30°C 30°C 1000 1,5 **    –– – – –

Hygiene 60°C 60°C 1100 5,5 ** –     – – – –

Synthetics 40°C 1100 3,0 2:1540°C      47 0,630 40 40

Rapid 30’ 30°C 30°C 1100 3,0 0:30 –   –66 0,250 42 26

Cotton 60°C 1100 5,5 2:4040 - 95°C      62 1,050 50 55

  Dosing required Dosing optional

PROGRAMMES

For choosing the appropriate programme for your kind of

laundry, always respect the instructions on the care labels

of the laundry. The value given in the tub symbol is the

maximum temperature possible for washing the garment.

Mixed

For washing lightly to normally soiled resilient garments in cotton, linen,

synthetic fibres and mixed fibres.

Eco 40-60

For washing normally soiled cotton garments declared to be washable

at 40 °C or 60 °C, together in the same cycle. This is the standard cotton

programme and the most efficient in terms of water and energy

consumption.

! The cycle runs only at 40°C as per regulation.

20 °C

For washing lightly soiled cotton garments, at a temperature of 20 °C.

Colours

White and pastel shaded garments made of delicate fabrics.

Gentle wash programme to avoid graying or yellowing of your laundry.

Use heavy duty detergent, if necessary also stain removers or bleaches on

oxygen basis. Do not use liquid detergent.

Wool

All wool garments can be washed using programme ‚ “Wool“ even

those carrying the “hand-wash only“ label. For best results, use special

detergents and do not exceed max kg declaration of laundry.

Spin

Spins the load then empties the water. For robust laundry.

Rinse + Spin

Separate rinse and intensive spin programme. For robust

laundry.

Delicates

For washing particularly delicate garments. Preferably turn garments

inside out before washing.

Hygiene

This program removes 99 % of bacteria while washing normally to heavily

soiled bed linen, table linen and underwear, towels, shirts etc. made of

cotton and linen.

Synthetics

For washing soiled garments made from synthetic fibres (such as

polyester, polyacrylic, viscose, etc.) or cotton/synthetic blends.

Rapid 30’

Shortly worn clothing made of cotton, polyester, polyamide and blends

with cotton. Brief programme to refresh your laundry.

Cotton

Normally to heavily soiled and robust cottons.

FIRST TIME USE

To remove any manufacturing debris select the “Cotton“ programme

at a temperature of 95°C. Pour a small quantity of detergent powder into

the main wash compartment of the detergent dispenser (maximum

1/3 of the quantity the detergent manufacturer recommends for lightly

soiled laundry). Start the programme without adding any laundry.

DAILY USE

Prepare your laundry according to the recommendations in the “HINTS

AND TIPS“ section. Load the laundry, close the drum door and check that

it is closed properly. Pour in the detergent and any additives. Observe the

dosing recommendations on the detergent pack. Close the lid. Turn the

programme selector to the desired programme and select any option if

needed. The display shows the duration of the selected programme (in

hours and minutes), and the indicator for the “Start/Pause“ button

flashes. The spin speed can be changed by pressing the “Spin“ button.

The indicator of the predefined spin speed lights up. Open the tap and

press the “Start/Pause“ button to start the wash cycle. The “Start/

Pause“ indicator will lights up and the door will be locked. Due to

variations in load and temperature of inlet water, the remaining time is

newly calculated in certain programme phases. If this is the case, an

animation appears on the time display.

PAUSE OR CHANGE A RUNNING PROGRAMME

To pause the wash cycle, press the “Start/Pause“ , the indicator button

light blinks. Select any new programme, options or spin speed if you wish

to change those settings. Press the “Start/Pause“ button again to start

the wash cycle from the point at which it was interrupted. Do not add

detergent for this programme.

LID OPEN INDICATOR

Before starting and after the end of a programme, the “Lid open“

indicator lights to show that the lid can be opened. As long as a wash

programme is running, the lid remains locked and must on no account

be forced open. In case you have an urgent need to open it during a

running programme, for example to add more laundry, or to remove

laundry which was loaded by mistake, press the “Start/Pause“

button. If the temperature is not too high, the “Lid open“ indicator

light turns on. It may last a while until you can open the lid. Press “Start/

Pause“ to proceed with the programme again.

PROGRAMME END

The “Lid open“ indicator lights up and the display shows .Turn

the programme selector to the “O“ position and close the water tap.

Open the lid and drum and unload the machine. Leave the Lid open

for some time to allow the interior of the machine to dry. After about a

quarter of an hour, the washing machine will switch off completely to

save energy.

To cancel a running programme before the end of cycle, press the

“Reset/Drain“ button for at least 3 seconds. The water is drained out.

It may last a while until you can open the lid.

OPTIONS

! When the combination of programme and additional option(s) is not

possible, the indication lights switch o automatically.

! Unsuitable combinations of options are deselected automatically.

Colours 15°

Saves energy used for water heating while maintaining a good wash

result. Supports colour maintenance when washing coloured laundry.

Recommendable for lightly soiled laundry without stains. Make sure that

your detergent is suitable for cold wash temperatures.

Fresh Care

Select this option if you cannot unload the laundry soon after

programme end, or if you tend to forget the laundry in your washing

machine. It will help to keep your laundry fresh. The washing machine

will start to tumble the laundry periodically after programme end. The

light of the “Fresh Care“ button will blink while this function is active,

and the display will show an animation. The periodic tumbling will last up

to approximately 6 hours after the end of your wash programme, and you

can stop it at any time by pressing the “Fresh Care“ button. It will last

a while until you can open the door. After the “Fresh Care“ period has

run out, the display indicates .

Start delay

To set the selected programme to start at a later time, press the “Start

delay“ button to set the desired delay time. The lamp for the

“Start delay“ option button lights up, and it goes off when the

programme starts. Once having pressed the “Start/Pause“ button,

the countdown of the time delay begins. Number of hours pre-selected

can be reduced by pressing the “Start delay“ button again. Do not

use liquid detergent when activating this option. To cancel the “Start

delay“ turn the programme selector to another position.

Rapid

Enables quicker washing by shortening the programme duration.

Recommendable for small loads or only lightly soiled laundry.

Prewash

Only for heavily soiled loads (for example sand, granular dirt). Increases

the cycle time by approximately 15 min. Do not use liquid detergent for

the main wash when activating the Prewash option.

Energy saver

With a lower temperature and slightly modified washing duration, the

optimum combination of excellent washing results

and even lower energy consumption is achieved.

Intensive rinse

Helps to avoid detergent residues in the laundry by extending the rinse

phase. Particularly suitable for washing baby laundry, for people suffering

from allergies and for areas with soft water.

Spin

Every programme has a predefined spin speed. If you want to change the

spin speed, press the “Spin“ button. If spin speed “0“ is selected, the

final spinning is cancelled but intermediate spin peaks remain during the

rinse. The water is drained out only.

CHILD LOCK

You can lock the buttons of the control panel against improper use (e.g.

by children). Press both of the child lock buttons simultaneously and hold

them for at least 3 seconds. The key symbol on the display lights

up. To unlock the buttons again proceed in the same way.

BLEACHING

Wash your laundry in the desired programme, Cotton or Synthetics

, adding an appropriate amount of chlorine bleach to the Softener

chamber (close the lid carefully). Immediately after the end of

the programme, turn the “Programme selector” and start the desired

programme again to eliminate any residual bleach smell; if you want, you

can add softener. Never put both chlorine bleach and softener into the

softener chamber at the same time.

HINTS AND TIPS

Sort your laundry according to

Type of fabric/care label (cotton, mixed fibres, synthetics, wool, handwash

items). Colour (separate coloured and white items, wash new coloured

items separately). Delicates (wash small items – like nylon stockings – and

items with hooks – like bras – in a cloth bag or pillow case with zip).

Empty all pockets

Objects like coins or lighters can damage your laundry as well as the

drum.

Appliance interior

If you never or seldom wash your laundry at 95°C, we recommend to

occasionally run a 95°C programme without laundry, adding a small

amount of detergent, to keep the interior of the appliance clean.

Follow the dosage recommendation / additives

It optimizes the cleaning result, it avoids irritating residues of surplus

detergent in your laundry and it saves money by avoiding waste of

surplus detergent

Use low temperature and longer duration

The most efficient programmes in terms of energy consumption are

generally those that perform at lower temperatures and longer duration.

Observe the load sizes

Load your washing machine up to the capacity indicated in the

“PROGRAMME CHART” table to save water and energy.

Noise and remaining moisture content

They are influenced by the spinning speed: the higher the spinning

speed in the spinning phase, the higher the noise and the lower the

remaining moisture content.

CLEANING & MAINTENANCE

For any cleaning and maintenance, switch off and unplug the washing

machine. Do not use flammable fluids to clean the washing machine.

Clean and maintain your washing machine periodically (at least 4 times

per year).

Cleaning the outside of the washing machine

Use a soft damp cloth to clean the outer parts of the washing machine.

Do not use glass or general purpose cleaners, scouring powder or similar

to clean the control panel – these substances might damage the printing.

Detergent dispenser

Clean regularly, at least three or four times a year, to prevent detergent

build-up:

Press the release button to release the detergent dispenser and 

remove it. A small quantity of water can remain in the dispenser, thus you

should carry it in an upright position. Wash the dispenser using running

water. You can also remove the siphon cap on the back of the

dispenser for cleaning. Replace the siphon cap in the dispenser (if

removed) Reinstall the dispenser by locating the dispenser’s bottom tabs

into the appropriate openings on the lid, and by pushing the dispenser

against the lid until it locks into place. Make sure that the detergent

dispenser is correctly reinstalled.

Checking the water supply hose

Check the inlet hose regularly for brittleness and cracks. If damaged,

replace it by a new hose available through our After-Sales Service or

your specialist dealer. Depending on the hose type: If the inlet hose has

a transparent coating, periodically check if the colour intensifies locally.

If yes, the hose may have a leak and should be replaced. For water stop

hoses (If available): check the small safety valve inspection

window (see arrow). If it is red, the water stop function was triggered, and

the hose must be replaced by a new one. For unscrewing this hose, press

the release button (if available) while unscrewing the hose.

Cleaning the mesh filters in the water supply hose

Check and clean regularly (at least two or three times a year).

Close the tap and loosen the inlet hose on the tap. Clean the internal

mesh filter and screw the water inlet hose back onto the tap. Now

unscrew the inlet hose on the rear of the washing machine. Pull off the

mesh filter from the washing machine connection with universal pliers

and clean it. Refit the mesh filter and screw the inlet hose on again. Turn

on the tap and ensure that the connections are completely water-tight.

Cleaning the water filter / draining residual water

The washing machine is provided with a self-cleaning pump. The filter

keeps objects like buttons, coins, safetypins etc. which have been left in

the laundry. If you used a hot wash programme, wait until the water has

cooled down before draining any water. Clean the water filter regularly, to

avoid that the water cannot drain after the wash due to obstruction of the

filter. If the water cannot drain, the indicator indicates that the water filter

may be clogged.

Open the filter cover with a coin. Place a broad, flat container beneath

the water filter, to collect the drain water. Slowly turn the filter

counterclockwise until water flows out. Let the water flow out, without

removing the filter. When the container is full, close the water filter by

turning it in clockwise. Empty the container. Repeat this procedure until

all the water has drained. Lay a cotton cloth beneath the water filter,

which can absorb a small amount of rest water. Then remove the water

filter by turning it out anti clockwise. Clean the water filter (remove

residues in the filter and clean it under running water) and the filter

chamber. Make sure the pump impeller (in the housing behind the filter)

is not obstructed. Insert the water filter and close the filter cover: Reinsert

the water filter again by turning it in clockwise direction. Make sure to

turn it in as far as it goes. To test water tightness of the water filter, you

can pour about 1 liter of water into the drum and check that water does

not leak from the filter. Then close the filter cover.

Lid seal

Check the condition of the lid seal periodically and clean it from time to

time with a damp cloth.

Recovering an object that falls between the drum and the tub

If an object accidentally falls between the drum and the tub, you can

recover it thanks to one of the removable drum lifters.

Unplug the washing machine. Remove the laundry from the drum. Close

the drum flaps and turn the drum a half-turn (picture ). Using a screw-a

driver press on the plastic end, while sliding the lifter from left to right

(picture , b c) by hand it will fall into the drum. Open the drum. You can

recover the object through the hole in the drum. Refit the lifter from

inside the drum: Position the plastic tip above the hole on the right side

of the drum (picture ). Then slide the plastic lifter from right to left until d

it clips. Close the drum flaps again, turn the drum through half a turn and

check the positioning of the blade at all its anchorage points. Plug the

washing machine in again.

TRANSPORT AND HANDLING

Pull out the mains plug, and close the water tap. Disconnect the inlet

hose from the water tap, and remove the drain hose from your draining

point. Remove all rest water from the hoses and washing machine and

fix hoses so that they cannot get damaged during transport. To facilitate

moving the machine, pull the mobility lever situated at the bottom

front (if available on your model) out a little by hand. Pull the washing

machine out to the stop with the foot. Afterwards push the mobility lever

back into the original stable position. Refit the transport bracket. Follow

the instructions for removing the transport bracket in the INSTALATION

GUIDE in reverse order.

abcd

Quick guide

Product specificaties

Merk:	Whirlpool
Categorie:	Wasmachine
Model:	TDLR 55140S EU

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool TDLR 55140S EU stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Wasmachine Whirlpool

Whirlpool FWSD 81283 SV EE N Handleiding

20 November 2024

Whirlpool FFWDB 864489 BV SPT Handleiding

20 November 2024

Whirlpool TDLR 55140S EU Handleiding

20 November 2024

Whirlpool TDLR 5040L EU/N Handleiding

20 November 2024

Whirlpool FSCR70211 Handleiding

20 November 2024

Whirlpool FFB 8448 BV EE Handleiding

20 November 2024

Whirlpool W8W846WR IT Handleiding

15 November 2024

Whirlpool BI WMWG 81484 Handleiding

15 November 2024

Whirlpool FFB 1048 BSV IT Handleiding

15 November 2024

Whirlpool FFB 108 SILVER IT Handleiding

2 November 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Haier HWMP95TL Handleiding

20 November 2024

Elektra Bregenz WAFS 81631 Handleiding

20 November 2024

Elektra Bregenz WAF 61427 Handleiding

20 November 2024

Elektra Bregenz WTS 81451 Handleiding

20 November 2024

Elektra Bregenz WAFM 81400 Handleiding

20 November 2024

Elektra Bregenz WAF 10147 Handleiding

20 November 2024

Elektra Bregenz WAF 71421 Handleiding

20 November 2024

Elektra Bregenz WAM 71425 Handleiding

20 November 2024

Elektra Bregenz WAF 71428 Handleiding

20 November 2024

Elektra Bregenz WAFS 72446 Handleiding

20 November 2024