Whirlpool FFB 8259 SV GCC Handleiding

Whirlpool Wasmachine FFB 8259 SV GCC

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool FFB 8259 SV GCC (3 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch o and unplug the washing machine.
Do not use ammable uids to clean the washing machine.
CLEANING THE OUTSIDE OF THE WASHING MACHINE
Use a soft damp cloth to clean the outer parts of the washing
machine.
Do not use glass or general purpose cleaners, scouring
powder or similar to clean the control panel – these
substances might damage the printing.
CHECKING THE WATER SUPPLY HOSE
Check the inlet hose regularly for brittleness and cracks. If
damaged, replace it by a new hose available through our
After-Sales Service or your specialist dealer.
Depending on the hose type:
If the inlet hose has a transparent coating, periodically check
if the colour intensies locally. If yes, the hose may have a leak
and should be replaced.
For water stop hoses: check the small safety valve inspection
window (see arrow). If it is red, the water stop function was
triggered, and the hose must be replaced by a new one.
For unscrewing this hose, press the release button (if
available) while unscrewing the hose.
CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE
1. Close water tap and unscrew the inlet hose.
1
2
2. Clean the mesh lter at the hose’s end carefully with a
ne brush.
3. Now unscrew the inlet hose on the back of the washing
machine by hand. Pull out the mesh lter from the valve
on the back of the washing machine with pliers and
carefully clean it.
4. Insert the mesh lter again. Connect the inlet hose to
water tap and washing machine again. Do not use a tool
to connect the inlet hose. Open the water tap and check
that all connections are tight.
2
1
CLEANING THE DETERGENT DISPENSER
CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER
Switch o and unplug the washing machine before cleaning the water lter or draining residual water. If you used a hot
wash programme, wait until the water has cooled down before draining any water.
Clean the water lter regularly, to avoid that the water cannot drain after the wash due to obstruction of the lter.
If the water cannot drain, the display indicates that the water lter may be clogged.
1. Remove the kick panel: Using a screwdriver, do that which
is shown in the following gure.
2. Container for the drained water:
Place a low and wide container under the water lter in
order to collect the residual water.
3. Drain the water:
Slowly turn the lter counter-clockwise until all the water
has come out. Allow the water to ow out without
removing the lter. Once the container is full, close the
waterlter by turning it clockwise. Empty the container.
Repeat the procedure until all the water has been drained.
4. Remove lter: Lay a cotton cloth beneath the water lter,
which can absorb a small amount of rest water. Then
remove the water lter by turning it out anticlockwise.
5. Clean the water lter: remove residues in the lter and
clean it under running water.
6. Insert the water lter and reinstall the plinth: Reinsert the water
lter again by turning it in clockwise direction. Make sure to turn
it in as far as it goes; the lter handle must be in vertical position.
To test water tightness of the water lter, you can pour about 1
liter of water into the detergent dispenser. Then reinstall the
plinth.
1
2
Remove the dispenser by raising it and pulling it out (see gure).
Wash it under running water; this operation should be repeated frequently.
1
2
1
2
1
2
1a
1b
2a
2b
3a
3b
4a
4b
A
B
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
1. Pull out the mains plug, and close the water tap.
2. Make sure that door and detergent dispenser are properly
closed.
3. Disconnect the inlet hose from the water tap, and remove
the drain hose from your draining point. Remove all rest
water from the hoses, and x them so that they cannot get
damaged during transport.
4. Ret the transport bolts. Follow the instructions for
removing the transport bolts in the “Installation Guide” in
reverse order.
Important: Do not transport the washing machine without
having xed the transport bolts.
AFTER-SALES SERVICE
BEFORE CALLING THE AFTER-SALES SERVICE
1. See if you can solve the problem by yourself with the help
of the suggestions given in the TROUBLESHOOTING
2. Switch the appliance o and back on again to see if the
fault persists.
IF AFTER THE ABOVE CHECKS THE FAULT STILL
OCCURS, GET IN TOUCH WITH THE NEAREST
AFTER-SALES SERVICE
To receive assistance, call the number shown on the warranty
booklet.
When contacting our Client After sales service, always specify:
a brief description of the fault;
the type and exact model of the appliance;
xxxxxxxxxxxx
the service number (number after the word Service on the
rating plate).
your full address;
your telephone number.
If any repairs are required, please contact an authorised after-
sales service (to guarantee that original spare parts will be used
and repairs carried out correctly).


Product specificaties

Merk: Whirlpool
Categorie: Wasmachine
Model: FFB 8259 SV GCC

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool FFB 8259 SV GCC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wasmachine Whirlpool

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine