Whirlpool AKT 352 Handleiding

Whirlpool Kookplaat AKT 352

Lees hieronder de 📖 handleiding in het Nederlandse voor Whirlpool AKT 352 (6 pagina's) in de categorie Kookplaat. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

AKT 352 PRODUCT DESCRIPTION SHEET

5019 319 01501 To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation.

CZ SK

LIGHTING THE BURNERS

• To ignite one of the burners, turn the relative knob anticlockwise to the maximum flame setting .

• Press the knob against the control panel to ignite the burner.

• After the burner has ignited, keep the knob pressed for about 5 seconds to allow the thermocouple to warm up.

This safety device shuts off the gas if the flame goes out accidentally (draughts, interruption of gas, liquids boiling over,

etc.).

• The device must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not

remain lit, wait at least one minute before trying to light it again.

- The burner might go out when the knob is released. This means that the thermocouple has not warmed up enough.

In this case, repeat the operations described above.

PRATICAL ADVICE FOR USING THE BURNERS

For optimum burner performance, observe the following

rules:

- Use pots and pans that fit the burners (see table on the

right).

- Only use flat-bottomed pots and pans.

- Use the correct amount of water for cooking foods and

keep the pot covered.

1. Removable grid(s)

2. Semi-rapid burner

3. Rapid burner

4. Semi-rapid burner control knob

5. Rapid burner control knob

SYMBOLS

Tap closed

Max. flame

Min. flame

Burner Pot Ø

Rapid from 24 to 26 cm

Semi-rapid from 16 to 22 cm

DIMENSIONS AND DISTANCES TO BE MAINTAINED (mm)

NOTE: In the event a hood is fitted above the cooktop, please refer to the hood instructions for the correct

distance.

INJECTOR TABLE CATEGORY II2H3B/P

ELECTRIC SUPPLY: 230 V ~ 50 Hz

Type of gas used Type of

burner

Injector

marking

Nominal heating

capacity

Nominal

consumption

Reduced

heating capacity

Gas pressure (mbar)

min. nom. max.

NATURAL GAS

(Methane) G20

rapid

semi-rapid

128

3.00

1.65

286 l/h

157 l/h

0.60

0.35 17 20 25

LIQUEFIED

PETROLEUM GAS

(Butane) G30

(Propane) G31

rapid

semi-rapid

3.00

1.65

218 g/h

120 g/h

0.60

0.35 20 30 35

Type of gas used Model configuration Nominal heating capacity

Total nominal

consumption

Air necessary (m3) for the

combustion of 1 m3 of gas

G20 20 mbar 2 burners 4.65 443 l/h 9.52

G30-G31 30 mbar 2 burners 4.65 338 g/h 30.94

PRECAUTIONS AND GENERAL RECOMMENDATIONS

To get full satisfaction from your hob, please read these instructions carefully and keep them for future

consultation

• These instructions are only valid for those Countries where the destination abbreviations are mentioned on the product

description sheet and on the hob.

• Keep the packaging material (plastic bags, polystyrene parts, etc.) out of the reach of children, as they are potentially

dangerous.

• Check whether the hob has been damaged during transport and remove any protective film from the appliance parts.

• This hob (Class 3) is designed solely for household use for cooking food. Any other use (such as heating

rooms) is to be considered improper and, as a consequence, dangerous.

• Make sure the installation and gas/electrical connections are carried out by a qualified technician in

compliance with the current local regulations.

• This appliance should only be installed and used in well-ventilated rooms, in accordance with current

regulations. Carefully read the instructions before installing and using this appliance.

• Gas adjustment and supply pressure are indicated on the rating plate located under the hob. If another

type of gas is to be used, refer to the section “Conversion to different types of gas”.

REFERENCE TO LOCAL REGULATIONS

Ensure that the installation and gas connections are performed by a qualified technician, following the manufacturer's

instructions and in compliance with current local safety regulations.

SAFEGUARDING THE ENVIRONMENT

1. Packaging

The packaging material is entirely recyclable, and is marked with the recycling symbol , which identifies it as a type of

material that must be sent to local waste-disposal centres.

2. Product

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the

environment and human health.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not

be treated as household waste. Instead, it must be delivered to an appropriate collection point for the recycling of

electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For further information on the treatment, recovery and recycling of this appliance, contact your competent local

authority, the collection service for household waste or the shop where you purchased the appliance.

Declaration of Conformity

• This cooking hob has been designed, constructed and marketed in compliance with:

- safety requirements of EEC “Gas” Directive 90/396;

- safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments);

- protection requirements of EEC “EMC” Directive 2004/108/EC;

- requirements of EEC Directive 93/68.

• This hob is suitable for contact with foodstuffs and complies with EEC (CE) Regulation n. 1935/2004.

CZ SK

NOTES:

• Improper use of the grids could scratch the hob. Do not position the grids upside down or drag them across the hob.

• If the hob has a glass ceramic top, do not use:

- Cast iron griddles or terracotta pots and pans

- Heat diffusers (e.g. metallic mesh)

- Two burners for the same pot

• In the event of prolonged use, additional ventilation may be needed (opening a window or increasing the extraction

force of the hood).

• The appliance is not intended for use by persons (children included) with physical, sensory or mental impairment or

without experience and knowledge of the appliance, unless supervised or previously instructed in its use by those

responsible for their safety.

• Keep children away from the hob when it is in use and do not let them play with the controls or any other appliance parts.

Warning: the protective rubber feet on the grids represent a choking hazard for young children. After removing the

grids, please ensure that all the feet are correctly fitted.

•Attention: the glass lid (if provided) may shatter if overheated. Before closing it, make sure that all the burners are off.

After use, make sure that the knobs are in position OFF and close the main gas delivery or cylinder tap

INSTALLATION

TECHNICAL INFORMATION FOR THE INSTALLER

• This product can be embedded in a worktop 20 to 40 mm thick.

• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening

in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper

surface of the work surface but, in no case less than 20 mm from the bottom of the hob. If there is an oven

beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The

manufacturer declines all liability if another brand oven is installed beneath the hob.

• Before installation, make sure that:

- the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the

rating plate and injector table).

- the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations.

- combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans.

- Continuous natural air circulation is ensured through a clear opening in a wall of at least 100 cm2. This wall opening must be:

a) permanent and in a wall to the outside of the room to be vented;

b) made in such a way that it cannot be obstructed from the inside or outside (not even accidentally);

c) protected by plastic grids, metallic mesh, etc., taking care not to reduce the air vent effective area mentioned above;

d) located near floor level and positioned so as not to interfere with the operation of the exhaust system.

INSTALLATION

GAS CONNECTION

• The gas supply system must comply with local regulations.

• You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no

information concerning your Country is given, please ask details to your Installer.

• The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel

pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying

with local regulations. The maximum length of the hose is 2 linear metres.

• Before connecting the tube to the elbow fitting (A), interpose the

washer (B) supplied, in compliance with EN 549.

Attention: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture.

It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length.

• After connection to the gas supply, check for leaks with soapy water.

ELECTRICAL CONNECTION

• The electrical connections must comply with local regulations.

• The data relevant to the voltage and power absorption are indicated on the rating plate.

• The earthing of this appliance is compulsory by law.

• The manufacturer cannot be held responsible for any injury to persons or animals or damage to property

arising from failure to comply with these requirements.

• When the hob is installed, provide a single-pole circuit breaker with a contact separation of at least 3 mm.

• If necessary, the electrical power cable must be replaced exclusively with a power cable having identical

characteristics to the original supplied by the manufacturer (type H05V2V2-F T90°C or H05RR-F).

This operation must be performed by a qualified electrician.

Assembly

1. Position the clips (A) in the spaces provided on the hob trim (fig. 3) if not already positioned.

2. Measure the centre point of the vertical sides of the cut-out (fig. 1)

3. Fit the brackets (C) in the centre of the vertical sides, aligning the upper edge of the brackets so that they are flush with

the worktop surface (fig. 2).

4. Fix the brackets with the 4 screws supplied (B) using the holes provided.

5. Insert the hob in the cutout, making sure the clips (A) are secured in the spaces provided (fig. 4).

Earth

(yellow/green)

fig. 2

fig. 1

For setting into a marble worktop, contact the After-sales Service for the installation kit and necessary

instructions.

4812 310 19277 Installation kit for marble worktop.

ADJUSTMENT TO DIFFERENT TYPES OF GAS

If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and orange sticker

applied on the top of the hob, change the injectors.

Remove the orange sticker and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Product Description Sheet.

• The gas nozzles must be changed by After Sales Service or a qualified technician.

• Nozzles not supplied with the appliance must be ordered from After Sales Service.

• Adjust the minimum setting of the taps.

Note: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as

it will go.

Should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the

replacement of the burner tap if found to be faulty.

REPLACING THE INJECTORS (see the injector table in the Product Description Sheet)

• Remove grids (A)

• Extract burners (B)

• Using a socket spanner of the appropriate size unscrew the injector (C)

• Replace it with the injector suitable for the new type of gas.

Before installing the hob, remember to affix the gas calibration plate

supplied with the injectors in such a way that it covers the existing

information relating to gas calibration.

fig. 4

fig. 3

Product specificaties

Merk:	Whirlpool
Categorie:	Kookplaat
Model:	AKT 352

Heb je hulp nodig?

Als je hulp nodig hebt met Whirlpool AKT 352 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Kookplaat Whirlpool

Whirlpool AKT8210 Handleiding

18 Maart 2022

Whirlpool AKR3710 Handleiding

7 Maart 2022

Whirlpool akt 812 ne Handleiding

15 Maart 2022

Whirlpool AKT8090NE Handleiding

17 Maart 2022

Whirlpool AKT8210LX Handleiding

16 Maart 2022

Whirlpool AKT 5000 Handleiding

17 Maart 2022

Whirlpool AKT 316 Handleiding

16 Maart 2022

Whirlpool AKT 320 Handleiding

15 Augustus 2022

Whirlpool akm 987 ba 01 Handleiding

22 Februari 2022

Whirlpool AKR 3711 Handleiding

26 Februari 2022

Handleiding Kookplaat

Nieuwste handleidingen voor Kookplaat

Teka FIH 16760 Handleiding

8 Juni 2024

Sencor SCP 2252 Handleiding

4 Juni 2024

Novy 1002 Handleiding

27 September 2023

Novy 3751 Handleiding

27 September 2023

Novy 1980 Handleiding

27 September 2023

Novy 1811 ONE Handleiding

27 September 2023

Novy 1102 Handleiding

27 September 2023

Novy 1109 Handleiding

27 September 2023

Thetford SHB 144 series Handleiding

26 September 2023

Thetford SHB 174 series Handleiding

26 September 2023