Vimar 03996 Handleiding

Vimar Schakelaar 03996

Lees hieronder de 📖 handleiding in het Nederlandse voor Vimar 03996 (6 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

03996

03997

Viale Vicenza, 14

36063 Marostica VI - Italy

www.vimar.com

EIKON

20196

ARKÉ

19196

PLANA

14196

20196-03996-03997EN 05 2204

20196, 19196, 14196 - Quid electronic switch for roller shutter with

slat orientation with relay outputs for cos 0.6 motor 2 A 220-240 V~ φ

50/60 Hz, position saving.

03996 - Quid electronic relay module for roller shutter with slat orien-

tation with relay outputs for cosφ 0.6 motor 2 A 220-240 V~ 50/60 Hz,

position saving, installation in junction boxes or connector block boxes.

The device is designed to control a load such as a roller shutter, shutter or curtain

while also allowing the adjustment of the position of the roller shutter or slats. It

is available in the version with 1-module double push button to match the Eikon,

Arké and Plana wiring series or for retrofit controlled by double push button. The

devices can be connected together and managed from a single centralised control.

The favourite roller shutter position can be saved and recalled starting from any

initial position.

03997 - Quid roller shutter control unit module, 2 inputs for NO push

button, 6 outputs for Quid roller shutter relay module 03996, 220-240

V 50/60 Hz power supply, installation in junction boxes or connector

block boxes.

The device, which can be installed inside connector block boxes, is designed to

manage several groups of roller shutters and control them from a single point.

CHARACTERISTICS of art. 20196, 19196, 14196 and 03996.

• Rated supply voltage: 220 – 240 V~ 50/60 Hz.

• Absorption: 13 mA.

• Relay output

• Controllable loads at 220-240 V~:

- resistive loads : 5 A (20,000 cycles);

- cos ø 0.6 motors: 2 A (20,000 cycles).

• Double push button for art. 20196-19196-14196

• LED for load status indication and programming.

• Terminals:

- motor  (UP) and (DOWN) relay contacts

- line L

- neutral N

- C and C  group control input to connect to art. 20062-19062-14062. For

art. 20196-19196-14196 additional local control input using art. 03997.

- in art. 03996 dedicated P and P input for local control (for instance art.  

20062-19062-14062, 20066-19066-14066).

• Number of roller shutters that can be connected: max. 20

• Max. length of cables for each section: 50 m

• Possible functions:

- roller shutter/curtain position adjustment.

- slat position adjustment.

- saving and calling of favourite roller shutter/curtain position starting from any

initial position.

- control from interlocked or non-interlocked double push button.

• Dissipated power of art. 03996: max. 1 W.

• In the event that several roller shutter relays are connected in order to cen-

tralise the system, using control unit module 03997 or directly on the general

control without additional modules in-between, the system must be set up

with a single Hysteresis and/or RCBO circuit breaker.

• It should be used in dry, dust-free places at a temperature of between 0 °C and

+45 °C.

Art. 03997 CHARACTERISTICS.

• Rated supply voltage: 220 – 240 V~ 50/60 Hz.

• Control via interlocked or non-interlocked double push button.

• In combination with art. 20196-19196-14196 is designed to insert an additional

local control.

• Designed to control 3 groups of roller shutters.

• Number of roller shutters that can be connected: max. 20

• Number of group levels: max. 3

• Max. length of cables for each section: 50 m

• It should be used in dry, dust-free places at a temperature of between 0 °C and

+45 °C.

CONFIGURATION of art. 20196,19196,14196 and 03996.

Configuration is done using the device dip switch and the control push buttons

(see figures 20196-19196-14196 and 03996). N.B. For art. 03996 switch off the

power supply before accessing the device and operating the dip switches.

TIMING

The relay is set by default with an operating time of 120 s; to modify this value,

proceed as follows:

• Lower the roller shutter/curtain until you reach the limit stop

• Position the dip switch on ; the LED begins to flash (if you press (SET DOWN)

nothing happens)

• Press and hold down ) to raise the roller shutter/curtain; the LED is perma (UP -

nently lit.

• Once the roller shutter/curtain reaches the limit stop, briefly press ( ) or DOWN

 ( ). UP

• The LED starts to flash again and the roller shutter/curtain moves for 1 s DOWN

and UP FOR 1 S.

• Replace the dip switch in the position; the LED goes out.OFF

FAVOURITE POSITION

Important: to make this setting you first need to have completed the TIMING

procedure.

• Take the roller shutter/curtain to your favourite position.

• Press   ( )/UP ( ) for 3 s or press briefly ) or ( ) 5 times; DOWN  (UP DOWN

the roller shutter/curtain moves for 1 s and for 1 s to confirm the DOWN UP

setting.

RESET

Shift the dip switch from the position to the position to reset all the setOFF SET -

tings made. In the event of a power failure, all the settings remain saved.

LOCAL AND GROUP CONTROL BUTTON FUNCTIONS.

• Press and hold down (for more than 1 s) = roller shutter/curtain opening/closing.

• Press briefly (less than 1 s) = slat adjustment.

• Press ( UP) or  (DOWN) briefly twice = recalls the favourite position.

INSTALLATION RULES.

• Installation must be carried out by qualified persons in compliance with the cur-

rent regulations regarding the installation of electrical equipment in the country

where the products are installed.

• The power supply circuit (L-N) must be protected against overloads by installing

a C10 A automatic 1-way switch.

• Art. 03996 and 03997 can be installed inside junction boxes provided they have

been declared suitable for electrical devices that dissipate energy.

REMOTE CONTROL RECEPTION.

Quid can be remote controlled using the following devices:

• DueFili+ video door entry system: Video Door App + art. 40507 + art. 69RH or

69PH (programmed for 2 s timed actuation)

The DueFili+ system is designed to configure a timed actuation (relay art. 69RH

or 69PH) and control it from video door entry indoor stations. If the indoor station

is connected (art. 40507) actuation can be remote controlled via the Video Door

App.

• IP video door entry system: Video Door App + art. 40607 + art. 40636 (pro-

grammed for 2 s timed actuation)

The IP video door entry system is designed to configure a timed actuation (relay

art.40636) and control it from video door entry indoor stations. If the indoor sta-

tion is connected (art. 40507) actuation can be remote controlled via the Video

Door App.

• GSM thermostat 01913: the device is fitted with a programmable output to

which an auxiliary supporting relay needs to be connected (a common one-posi-

tion stable relay with a 230V coil is sufficient). Actuation is then controlled via the

By-Phone App or the By-Clima App (or directly via SMS text message).

REGULATORY COMPLIANCE.

LV Directive. EMC directive. EN 60669-2-1 standard.

REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces

of lead.

Viale Vicenza, 14

36063 Marostica VI - Italy

www.vimar.com

20196-03996-03997EN 05 2204

03997

Dip switch

LED

OFF

SET

20196-19196-14196

C N L

6 mm

 = Motor DOWN

 = Motor UP

L = Phase

N = Neutral

C = DOWN local and group control input

C = UP local and group control input

 1 = DOWN group 1 input 2 = DOWN group 2 input

 1 = UP group 1 input 2 = UP group 2 input

 C = DOWN control input 3 = DOWN group 3 input

 C = UP control input 3 = UP group 3 input

03996

 = Motor DOWN

 = Motor UP

L = Phase

N = Neutral

P = DOWN control input

P = UP control input

C = DOWN group control input

C = UP group control input

Dip switch

LED

SET OFF

6 mm

220-240V~ 50/60Hz

2A μ

03996

P P C CL N

WEEE - User information

The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life must be collected separately from other waste. The user must therefore hand the equipment at the end of its life cycle over to the ap-

propriate municipal centres for the differentiated collection of electrical and electronic waste. As an alternative to independent management, you can deliver the equipment you want to dispose of free of charge to the distributor when purchasing

a new appliance of an equivalent type. You can also deliver electronic products to be disposed of that are smaller than 25 cm for free, with no obligation to purchase, to electronics distributors with a sales area of at least 400 m 2

. Proper sorted

waste collection for subsequent recycling, processing and environmentally conscious disposal of the old equipment helps to prevent any possible negative impact on the environment and human health while promoting the practice of reusing

and/or recycling materials used in manufacture.