Valcom VIP-130L Handleiding

Valcom Speaker VIP-130L

Lees hieronder de 📖 handleiding in het Nederlandse voor Valcom VIP-130L (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

1 947628

ISSUE 3

VIP-130L IP Paging Horn

INTRODUCTION

The VIP-130L IP Paging Horn is a self contained

paging system which enables voice paging up to

1200 feet from an Ethernet connection. The

VIP-130L consist of a high eﬀiciency 5 Watt

Class- Horn and a P-LLE Network Extender D VI

allowing stand alone capability when used with a

SIP enabled telephone System or can be

accessed from a variety of Valcom managed

VoIP products.

SPECIFICATIONS

Access Methods

PBX, FXO Port w/VIP-811

POTS telephone set w/VIP- 811

PBX, FXS Port w/VIP-821

Valcom M Cast Page Group

SIP enable telephone system –

Features

- network connection RJ 45

LED Status Indicator

Network activity LEDs

802.3af compliant

High Eﬃciency Class-D 5 Watt Ampliﬁer

Dimensions/Weight

(Horn)

H x 00" W x 1 " D 7.00”10. 0.00

(18.75 cm H x cm W x cm D) 25.4 26.4

Weight: 8 lbs. ( 63 kg) 5. 2.

Network Extender

(VIP- ) LLE

0" W x 6. " D 1.30” H x 6.1 00

(3.51 cm H x 15.72 cm W x 13.51 cm D)

Weight: 0.85 lbs. (0.39 kg)

Nominal Speciﬁcations HORN –

Input Impedance: 600 Ohms

Input Level: -10dBm

Output Impedance: 600 Ohms

Output Level: -10dBm nominal

Nominal Speciﬁcations VIP- –LLE

Via 802.3af PoE Ethernet Switch:

Class 3 (12.95W)

Environment

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

Packing List

Qty

Item

VIP-LLE Network Extender

5 Watt High Eﬃciency Horn

VSP Document

Mounting Brackets

Rubber Pads

Wood Screws

RJ-45 Termination Block

RJ-45 Patch Cable

2 947628

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualiﬁed service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

INSTALLATION

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses and can radiate

radio frequency energy and if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference in which case the user

will be required to correct the interference at

his own expense.

Precautionary Designations

Mounting (VIP- )LLE

The VIP-L Network Extender is designed for LE

wall or shelf mounting and must be within 300

feet of the network switch.

Shelf: Provided with the VIP-L Network LE

Extender are four rubber pads. Peel the pads

from the carrier backing and place at the four

corners of the bottom of the unit.

Wall: Using the brackets and wood screws

provided, secure the VIP-L Network Extender LE

to the wall.

Mounting (HORN)

The horn should be mounted 15 to 20 feet

above the ﬂoor to allow for best sound

distribution. The unit can be mounted to a wall,

a beam or an electrical box.

NOTE: For ease of installation, the base can be

attached to the speaker before or after the base

is mounted.

Loosen position adjustment knob

Insert the ball of the base into the socket

of the speaker

Tighten the position adjustment knob

Mount the base to a wall using the two

holes provided. Knockout holes are

provided for punch out should additional

holes be desired.

clamp is provided with the horn to A “C”

allow mounting to a beam. Place the

bolt through the hole in the bottom of the

base to secure the “C” clamp to the

beam. It is suggested that the horn be

mounted to the underside of the “I”

beam to provide maximum positioning

adjustments.

Connection to an electrical backbox is

accomplished by channeling wire

through the ball of the base and making

appropriate connections. The base has

holes punched for a double-gang square

box, but by punching out additional

knockout holes, the base can be

mounted to a single-gang or octagon

box

The horn may be rotated or moved up and down

to obtain the desired position by loosening the

position adjustment knob at the bottom of the

unit approximately one turn. Make required

adjustments and re- en knob. tight

Interconnections

The method of powering the VIP-130 IP only L

Paging Horn is via a power over Ethernet switch

or power injector meeting the 802.3af

speciﬁcation .

Make all required signal connections before

connecting to Ethernet switch or power injector

meeting the 802.3af specification. Power is

supplied to the horn assembly via the

VIP-L Network Extender. LE

3 947628

W/BL W/O W/GN W/BR

900' MAX DISTANCE

CAT 3/5/6

BLORBK

GYBRYL

W/BR PAIR

BL/W

W/BL

W/GN PAIR

*W/O PAIR NOT USED

Ampliﬁed

Paging Horn

RJ-45

Termination Block

Act

Status

Link

VIP-LLE

ALCOM

Signal Connections (Fig. 1)

Connect CAT- cable from rear panel color 5 the

coded connector of the VIP-L Network LE

Extender to the supplied RJ-45 termination block

(900 feet maximum distance). Use the supplied

CAT-5 patch cable to connect the -RJ 45

connector of horn to RJ-45 termination block.

Network Connection (Fig. 1)

The VIP-L Network Extender has one CAT-5 LE

RJ- connector on the front panel 45 “NETWORK”

and one CAT- color-coded connector on the 5

rear panel.

Use the supplied CAT-5 patch cable to connect

the NETWORK connector of the VIP-LLE

Network Extender to a 802.3af compliant PoE

port (300feet maximum distance).

Status Indicator Lights

The VIP-LLE Network Extender has 3 status

indication lights:

STATUS: Flashes during normal operation, and

solid when unit in reset.

LINK: Indicates 100 Mbit Ethernet connection

when illuminated. No activity indicates 10 Mbit

connection.

Act: Indicator ﬂashes to indicate network

activity

Operation

Provide paging from SIP connection or via a

variety of Valcom managed VoIP products.

Integration to customer telephone system can

be via SIP registration, FXO port (with VIP-811),

or FXS port (with VIP-821).

Front View

Rear View

Figure 1

Product specificaties

Merk:	Valcom
Categorie:	Speaker
Model:	VIP-130L
Kleur van het product:	Wit
Gewicht:	2630 g
Breedte:	254 mm
Diepte:	264 mm
Hoogte:	187.5 mm
Ethernet LAN:	Ja
Type stroombron:	Power over Ethernet (PoE)
Aantal Ethernet LAN (RJ-45)-poorten:	1
Gemiddeld vermogen:	5 W
Certificering:	FCC 15, CE, WEE\n
Netwerkstandaard:	IEEE 802.3af
Aanbevolen gebruik:	Overige
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Muur-montage
Aantal drivers:	1
Frequentiebereik:	- Hz
AC-adapter, uitgangsspanning:	24 V
AC-adapter, uitgangsstroom:	0.325 A
Compatibiliteit:	Cisco, Nortel, Avaya
Luidspreker soort:	1-weg
Wifi:	Ja