TP Link VIGI C230I Mini Handleiding

TP Link Bewakingscamera VIGI C230I Mini

Lees hieronder de 📖 handleiding in het Nederlandse voor TP Link VIGI C230I Mini (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick Start Guide

*Images may dier from actual products.

Appearance

Power Supply Interface

(12V DC)

RJ45 Ethernet Port

(supports PoE)

Micro SD Slot

Side Screws

Speaker

Package Contents

Network Camera Mounting Bracket

Quick Start Guide

Anchors and Screws

Quick

Start

Guide

•

Make sure your power supply matches your camera.

The camera’s standard power supply is 12V DC or

PoE (802.3af/at). The power source should meet LPS,

PS2, and other requirements according to IEC

62368-1.

• Make sure that the wall is strong enough to

withstand 4 times the weight of the camera and

mounting bracket.

• If you are uncertain or uncomfortable performing the

installation, consult a qualied electrician.

Safety First:

Mounting Template

2. Decide how to route the cable through the ceiling/wall. 4. Loosen the lens screw, rotate the lens base to adjust the

angle of the lens as desired, and then tighten the lens screw.

Tighten the side screws to secure the cover.

3. Loosen the three screws on the side of the camera to

remove the cover. Push the camera upwards and rotate

the camera clockwise to snap it into the mounting bracket.

1. Stick the mounting template to the desired mounting place.

Drill 3 screw holes according to the template, then install the

mounting bracket.

3MP Mini Dome Network Camera

Reset Button

Microphone

Mounting Template

Mounting Bracket

Point one of the arrows on the

mounting template in the direction

of the lens and stick it to the

ceiling/wall.

Lens Base

Dome

Anchor

Self-tapping Screw

Install mounting bracket

Reinstall the coverAdjust lens angle

Snap the camera into

the bracket

Press for 5 seconds to reset the

camera to factory settings.

Note: You can also slightly adjust the direction of the dome, but make sure that the

arrow symbol on the dome does not exceed the notch on the lens base.

Remove the cover

Ceiling or Wall

Route the cable through the

round hole in the middle of

the upper mounting bracket

Knock out the cable hole on the

side and route the cable from

the side

Lens Screw

Loosen to remove the cover.

More Management Methods

1. Download the on your VIGI Security Manager

computer at

https://www.tp-link.com/support/download/vigi-s

ecurity-manager/.

2. Install the and open it. VIGI Security Manager

3. Cameras on the same network as your computer

can be automatically discovered. Go to Settings >

Discovered Devices + Add, click to activate your

discovered cameras by setting passwords, and

follow the instructions to add your cameras.

Method 1: Via the VIGI Security Manager

(Windows only)

You can also access and manage your cameras via any of the methods below.

View live video and modify camera settings on

your computer.

Method 3: Via a Web Browser

View live video and modify camera settings via a

web browser.

1. Find the camera's IP address on your router’s client

page.

2. On your local computer, open a web browser and enter

https://camera's IP address (https://192.168.0.60 by

default).

3. Select your Country/Region and Time Zone.

4. Set a password to activate the camera.

Done. You can view the live video on the Preview page, and

go to the Settings page to change camera settings.

Method 2: Via the TP-Link VIGI App

Remotely view live video, manage cameras, and

get instant alerts.

Use Your Camera with an NVR

VIGI NVR

Monitor

Network Device

(e.g., Switch or Router)

The camera works with an NVR for easier batch access and management.

*Here we use a VIGI NVR as an example.

Frequently Asked Questions (FAQ)

Q1: What can I do if no cameras are discovered?

• Refresh to discover your camera again.

• Make sure the camera is powered on.

• Make sure your camera and NVR/computer are in the same subnet. If not,

use the VIGI Security Manager to set camera’s network parameters.

• Try to add your cameras manually.

• For other NVR brands, make sure you have activated the camera by setting

a password via the or app. VIGI Security Manager TP-Link VIGI

Q2: How do I know the camera is powered on?

• The IR LED will turn on for about 10 seconds once the camera is powered on. If

it’s o, you can cover the lens for several seconds and check if the IR LED turns

on.

• Check the LED status of the network device your camera is connected to.

For more questions, please refer to

https://www.tp-link.com/support/faq/2850/

• Do not use any other chargers than those recommended.

• Do not use damaged charger or USB cable to charge the device.

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

• Adapter shall be installed near the equipment and shall be easily accessible.

• Keep the device away from water, fire, humidity or hot environments.

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant

provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant

provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety)

Regulations 2016.

The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/

Network Camera

Step 2. Power On the Cameras

Power on your cameras with the PoE power supply

or an external power supply.

Step 1. Connect the Hardware

Connect your cameras to the same network as your

NVR (as shown above).

Step 3. Add Cameras with the NVR

Before you start, make sure the NVR is working properly.

1. Right click on the Live View screen and click Add

Camera.

2. Select your camera and click + to add your camera

directly. If you have disabled Plug and Play on your

NVR, create a password or use a preset password

for your camera.

Note: If you can’t nd your camera, refer to FAQ-Q1.

Done! You can now view live video and manage cameras.

Using your cameras with other NVR brands:

Step 1: Power on your cameras and connect them to the network.

Step 2: Activate the camera using the or app (refer to the next section).VIGI Security Manager TP-Link VIGI

Step 3: Refer to the NVR’s User Manual to add cameras.

1. Download and install the app.TP-Link VIGI

2. Open the app and log in with your TP-Link VIGI

TP-Link ID. If you don’t have an account, sign up rst.

3. Tap the button on the top right and follow the app +

instructions to activate and add your cameras.

For technical support, replacement services, user guides, and more

information, please visit https://www.tp-link.com/support, or simply

scan the QR code.

Product specificaties

Merk:	TP Link
Categorie:	Bewakingscamera
Model:	VIGI C230I Mini

Heb je hulp nodig?

Als je hulp nodig hebt met TP Link VIGI C230I Mini stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera TP Link

TP Link VIGI C450 Handleiding

18 December 2024

TP Link InSight S245 Handleiding

10 December 2024

TP Link Tapo C230 Handleiding

3 December 2024

TP Link Tapo C222 Handleiding

3 December 2024

TP Link InSight S445ZI Handleiding

13 November 2024

TP Link InSight S445 Handleiding

13 November 2024

TP Link Tapo TC72 Handleiding

11 November 2024

TP Link Tapo D235 Handleiding

11 November 2024

TP Link Tapo C501 Handleiding

11 November 2024

TP Link Tapo A100 Handleiding

11 November 2024

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Honeywell HC35WE5R3 Handleiding

20 December 2024

Honeywell Performance H4W8PER2V Handleiding

20 December 2024

Hikvision DS-2CE12KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE78D0T-LXTS/A Handleiding

18 December 2024

Hikvision DS-2CE76U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE78U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE16U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LSYE Handleiding

18 December 2024

Hikvision DS-2CE17U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LS Handleiding

18 December 2024