TP Link TL-SG1005LP Handleiding

TP Link Schakelaar TL-SG1005LP

Lees hieronder de 📖 handleiding in het Nederlandse voor TP Link TL-SG1005LP (3 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Connection

Installation Guide

5-Port Gigabit Desktop PoE Switch

LED Explanation

Note: For simplicity, we will take TL-SG1005P for example throughout this Guide.

Note: 1. PoE ports can also connect to non-PoE devices, but only transmit data.

2. TL-SG1005LP can supply up to 30 W for each PoE port and 40 W for

all PoE ports.

3. TL-SG1005P can supply up to 30 W for each PoE port and 65 W for all

PoE ports.

DC Power Adapter

AC Power Cord

IP Camera AP IP Phone

PoE Devices

Router

LAN Port WAN Port

Internet

Ethernet Ports (1-5)

PoE Ports (1-4)

Power

On: Power on

O: Power o

Power

PoE MAX

PoE Max

TL-SG1005LP

On: 33 W ≤ Total power supply < 40 W

Flashing: Total power supply ≥ 40 W

O: Total power supply < 33 W

TL-SG1005P

On: 58 W ≤ Total power supply < 65 W

Flashing: Total power supply ≥ 65 W

O: Total power supply < 58W

Link/Act and PoE Status

On: Providing PoE power

Flashing: Current-overload/Short-circuit

O: Not providing PoE power

On (Green): Connected to a 1000 Mbps

device

On (Yellow): Connected to a 10/100 Mbps

device

Flashing: Transmitting/receiving data

O: No device is connected to the

corresponding port.

Frequently Asked Questions (FAQ)

The Power LED should be lit when the power system is working normally. If the

Power LED is not lit, please try the following:

A1:

Make sure the AC power cord is connected to the switch with power source

properly.

A2:

Make sure the voltage of the power supply meets the requirements of the input

voltage of the switch.

A3: Make sure the power source is on.

Q1. Why is the Power LED not lit?

Please try the following:

A1:

Make sure that the cable connectors are rmly plugged into the switch and the

device.

Make sure the connected device is turned on and works normally.

The cable must be less than 100 meters long (328 feet).

Q2. Why is the Link/Act LED not lit while a device is connected to

the corresponding port?

Q3. Why are PoE ports not supplying power for PoE devices?

When the total power consumption of connected PoE devices exceeds the

maximum, the PoE port with a smaller port number has higher priority. The system

will cut o power to the ports with larger port numbers to ensure supplying to other

ports.

Take TL-SG1005P as an example. If port 1, 2 and 4 are consuming 15.4 W

respectively, and an additional PoE device with 19 W is inserted to port 3, the system

will cut o the power of port 4 to compensate for the overload.

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність

вимогам нормативних документів та вимогам, що передбачені чинними законодавчими

актами України.

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device.

Do not use damaged charger or USB cable to charge the device.

Do not use any other chargers than those recommended.

Adapter shall be installed near the equipment and shall be easily accessible.

Place the device with its bottom surface downward.

Use only power supplies which are provided by manufacturer and in the origin

packing of this product. If you have any questions, please don’t hesitate to contact us.

TP-Link hereby declares that the device is in compliance with the essential requirements and

other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU

and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.

EU Declaration of Conformity

IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x,

IEEE802.3af, IEEE802.3at, IEEE802.1p

CSMA/CD

5 10/100/1000 Mbps RJ45 Ports

Auto-Negotiation MDI/MDIX

PoE Ports: Port 1-Port 4,

Total Power Supply:

40 W (TL-SG1005LP)/65 W (TL-SG1005P)

10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);

EIA/TIA-568 100Ω STP (maximum 100 m)

100BASE-TX: UTP category 5, 5e cable (maximum

100 m); EIA/TIA-568 100Ω STP (maximum 100 m)

1000BASE-T: UTP category 5e cable or above (maximum

100 m); EIA/TIA-568 100Ω STP (maximum 100 m)

10 Gbps

2 K

Store-and-Forward

Automatically learning, automatically aging

External Power Adapter

Input: 100-240 VAC, 50/60 Hz

Output:

53.5 VDC /0.81 A (TL-SG1005LP)

53.5 VDC /1.31 A (TL-SG1005P)

Yes

52 mm

Standard

Protocol

Interface

General Specications

Operating Temperature

Storage Temperature

Operating Humidity

Storage Humidity

0 C to 40 C (32 F to 104 ˚ ˚ ˚ ˚F)

-40 C to 70 C (-40 F to 158 ˚ ˚ ˚ ˚F)

10% to 90%RH non-condensing

5% to 90%RH non-condensing

Environmental and Physical Specications

Specications

Wall Mountable

Distance Between

Mounting Holes

Network Media (Cable)

Switching Capacity

MAC Address Table

Transfer Method

MAC Address Learning

PoE Disclaimer

PoE budget calculations are based on laboratory testing. Actual PoE power budget is not

guaranteed and will vary as a result of client limitations and environmental factors.

For technical support and other information, please visit

https://www.tp-link.com/support, or simply scan the QR code.

If you have any suggestions or needs on the product guides,

welcome to email techwriter@tp-link.com.cn.

To ask questions, find answers, and communicate with TP-Link

users or engineers, please visit https://community.tp-link.com

to join TP-Link Community.

Power Supply

Explanation of the symbols on the product label

DC voltage

RECYCLING

This product bears the selective sorting symbol for Waste electrical and

electronic equipment (WEEE). This means that this product must be handled

pursuant to European directive 2012/19/EU in order to be recycled or

dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization

or to the retailer when he buys a new electrical or electronic equipment.

Indoor use only

Polarity of output terminals

Energy eciency Marking (Level VI)

FCC compliance information statement

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been

shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized

change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2020.2.24

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.• Reorient or relocate

the receiving antenna.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been

shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized

change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2020.2.24

Product Name: I.T.E. POWER SUPPLY

Model Number: T535081-2-DT/T535131-2-DT

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc.

Address: 145 South State College Blvd. Suite 400, Brea, CA 92821

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6803

E-mail: sales.usa@tp-link.com

FCC compliance information statement

Product Name: Gigabit Desktop Switch

Model Number: TL-SG1005LP/TL-SG1005P

Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc.

Address: 145 South State College Blvd. Suite 400, Brea, CA 92821

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6803

E-mail: sales.usa@tp-link.com

Component Name Model

I.T.E. POWER SUPPLY T535081-2-DT (For TL-SG1005LP)

T535131-2-DT (For TL-SG1005P)

Mounting Requirements

To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8#

standard and are more than 8.5 mm in length. When the screws are xed on the wall, the distance

between the screw head and the wall should be more than 1.5 mm.

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

This is a class A product. In a domestic environment, this product may cause radio interference,

in which case the user may be required to take adequate measures.

CE Mark Warning

請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

注意防潮，請勿將水或其他液體潑灑到本產品上。

插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。

BSMI Notice

安全諮詢及注意事項

限用物質含有情況標示聲明書

限用物質及其化學符號

鉛

鎘

汞

六價鉻

Cr+6

多溴聯苯

PBB

多溴二苯醚

PBDE

產品元件名稱

PCB

外殼

電源供應器

備考1. “ “系指該項限用物質之百分比含量未超出百分比含量基準值。

備考2. “ “系指該項限用物質為排除項目。

Standard Diameter

ANSI B1.1 #4

ANSI B1.1 #8

ANSI B1.1 #6

ANSI B1.1 #5

2.845 mm

3.175 mm

4.166 mm

3.505 mm

Product specificaties

Merk:	TP Link
Categorie:	Schakelaar
Model:	TL-SG1005LP
Kleur van het product:	Zwart
Breedte:	99.8 mm
Diepte:	98 mm
Hoogte:	25 mm
LED-indicatoren:	Ja
Gebruiksaanwijzing:	Ja
Vermogensverbruik (max):	47.5 W
Certificering:	FCC, CE, RoHS
Netwerkstandaard:	IEEE 802.1p, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
Temperatuur bij opslag:	-40 - 70 °C
Luchtvochtigheid bij opslag:	5 - 90 procent
Rack-montage:	Nee
Vermogenstoevoer inclusief:	Ja
Ophangsysteem voor aan de muur:	Ja
Quality of Service (QoS):	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Ja
Switchingcapaciteit:	10 Gbit/s
MAC-adrestabel:	2000 entries
10G support:	Nee
Datastroombeheer:	Ja
IGMP snooping:	Ja
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	5
Type basis-switching RJ-45 Ethernet-poorten:	Gigabit Ethernet (10/100/1000)
Jumbo Frames ondersteuning:	Ja
Koperen ethernetbekabelingstechnologie:	10BASE-T, 100BASE-TX, 1000BASE-T
Warmtedissipatie:	161.98 BTU/h
Auto-negotiation:	Ja
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50/60 Hz
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Code geharmoniseerd systeem (HS):	85176990
Totaal Power over Ethernet (PoE)-budget:	40 W
Aantal Power over Ethernet plus (PoE +)-poorten:	4
Verzending snelheid:	7.44 Mpps
Jumbo frames:	16000
Fanloos:	Ja
Store-and-forward:	Ja
Ondersteundende kabel types:	Cat3, Cat4, Cat5, Cat5e, Cat6
MAC-adres zelfverouderende functie:	Ja
MAC-adres zelflerende functie:	Ja