TP Link Tapo D235 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor TP Link Tapo D235 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
*Images may dier from your actual product.7106511276 REV1.0.1
Video Doorbell Camera
Quick Start Guide
OR
Tapo
3M
3M
UP
Take care to avoid electric shocks. *Recommended Installation Height: 1.2 m (4 ft) above the ground
Install Your Doorbell
03 /
Option 1. Stick to the wall
1. Attach the included adhesive to the back of the bracket or the wedge you have selected. If you use the
wedge, aîž±x the bracket and the wedge with screws.
2. Route the wires through the bracket (if there are existing wires) . Wipe o the dust from the surface using
a dry cloth, stick the bracket with adhesive to the smooth wall, and press it down for 15 seconds to
ensure the bracket is rmly attached.
Note: This is applicable with tile, glass, marble, metal, stainless steel, and smooth wall surfaces.
Mounting Wedge3M Adhesive3M Adhesive
Requires:
• Mounting Bracket
• 3M Adhesive
Note: The adhesive is for one-time use. Avoid re-using the adhesive to ensure its adhesion.
Requires:
• Mounting Bracket
• 3M Adhesive
• Horizontal or Vertical
Mounting Wedge
• Mounting Wedge
Screws ×4
Flip the page over for , and more. Option 2
3M
3M
UP
5V/2A USB Charger
Set Up Your Doorbell and Chime
2. Download the Tapo app from the App Store or
Google Play.
3. Press and hold the button on the back of ON/OFF
the doorbell for to turn it on.3 seconds
1. Plug in the USB cable to charge your doorbell.
When you plug in the charger, the LED should
blink amber quickly for 3 seconds.
4. Tap the button in the app and select your
model. Follow the app instructions to set up your
doorbell and pair with the chime.
Note: If you didn’t pair the chime during the setup, please
refer to https://www.tp-link.com/support/faq/3818/.
1. Turn o the circuit breaker. Make sure the power is
o by ringing your doorbell a few times.
OFF
01 / Install Jumper Wire for Your Existing Chime
Take care to avoid electric shocks.
2. Remove the chime cover and take a photo of the
wiring in case you want to reconnect it.
4. Tighten the screws and replace the chime cover. If
you want to disable Always-On Mode, just remove the
jumper wire.
Note: If your doorbell chime has dierent markings, consult a
licensed electrician.
3. Slightly loosen the screws for the and of Front Trans
your doorbell or the and of your front Rear Trans
rear doorbell, then insert the included jumper wire.
Front Doorbell
TRANS TRANSREARFRONT
Rear Doorbell
Preparations for Installing Your Doorbell
02 /
1. Remove your existing doorbell on the door. Then
disconnect the wires.
2. (Optional) Select the mounting wedge to adjust the
viewing angle of the doorbell.
Without Mounting
Wedge
With Vertical
Mounting Wedge
Without Mounting
Wedge
With Horizontal
Mounting Wedge
15°
5°
Mount Your Doorbell
Note:
1. Charge the doorbell before use. This will take about 6 hours.
2. The USB charger is not provided.
3. Peel o lm from the doorbell before use.
4. Warning: Do not tear o the silicone part by force as it may aect
the waterproof performance.
5. Keep the ports rmly covered when not in use to ensure
waterproof performance.
Option A: Battery Powered Option B: Hardwire Powered
If you don’t have existing doorbell wiring at the door,
use the built-in battery. You are free to determine
the doorbell position and the mounting is easy and
quick.
When the doorbell battery level is low, you need to
detach and charge it.
For installation, skip 01/ Install Jumper Wire for
Your Existing Chime and choose either installation
option to install your doorbell without existing wires.
Determine Power Options
You can choose whether to enable Always-On
Mode, which supports 24/7 recording.
WARNING: Risk of Electric Shocks
• Your existing doorbell must be wired (not battery
powered) and supplied by an 8-24V AC, 10VA
minimum transformer.
• Ensure that your existing doorbell works by ringing
the doorbell.
• Locate your existing doorbell chime.
• Disconnect power at the fuse or circuit breaker
before installing.
• You can always nd detailed wiring and installation
instructions in the Tapo app.
8-24V
Enabling requires bypassing Always-On Mode
your existing chime.
For installation, follow instructions in the Mount
Your Doorbell section to bypass your existing
chime and install your doorbell.
Disabling allows using your Always-On Mode
existing chime. Hardwiring provides a constant
power source.
For installation, skip 01/ Install Jumper Wire for
Your Existing Chime and then install your doorbell.
(Only necessary when hardwiring the doorbell and enabling Always-On Mode.)
3. Mount the doorbell to the bracket.
Option A: Battery Powered
Mount the doorbell to the bracket.
Requires:
• Video Doorbell Camera Note: If the wires are too short, use the included extension
wires and wire nuts to make them longer.
If the wires are too short:
Requires:
• Video Doorbell Camera
• (Optional) Extension Wires ×2, Wire Nuts ×2
Option B: Hardwire Powered
Connect the wires to the doorbell and tighten the
screws. Mount the doorbell to the bracket and turn on
the circuit breaker.
UP
UP
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/
setup-video/#cloud-cameras
Doorbell Appearance
Option 2. Mount to the wall
1. Route the wires (if there are existing wires) through the mounting template and stick the template. Drill two
holes where indicated.
Note: When mounting to uneven walls, stick the foam pad on the back of the bracket or wedge.
2. Route the wires (if there are existing wires) through the bracket. Insert two anchors into the holes and use the
screws to aîž±x the bracket over the anchors.
Φ=6 mm (15/64 in.)
Requires:
• Mounting Template
Requires:
• Mounting Anchors ×2
• (Optional) Foam Pad
• (Optional) Horizontal or
Vertical Mounting Wedge
• Mounting Bracket
• Mounting Screws ×2
Mounting Wedge (Optional)Foam Pad (Optional)
Chime Appearance
• Use a pin to press and hold for : Reset Wi-Fi settings 5s
• Use a pin to press and hold for : Reset to factory 10s
settings
Reset Button
Speaker1
2
LED
3
Press to cycle through dierent ringtones.
Music Button5
Press to adjust the volume of the ring.
Volume Button
4
1
2
35
4
UP
How to Detach Doorbell
Safety Information
Use the doorbell detaching pin provided if you wish to
detach the doorbell from the mounting bracket.
microSD
5
6
2
4
1
8
12
3
2
4LED
Lens
Light Sensor3
1Microphone
Motion Sensor (PIR)
5
Speaker6
Ring Button7
11
10
9
Press and hold for : Reset to factory settings5s
SYNC/RESET Button
8
microSD Card Slot10
Tear o the silicone cover and insert a microSD card.
Initialize it on the Tapo app before use.
*microSD card not included
Type-C Port11
Plug in the USB cable to charge your doorbell.
ON/OFF Button12
Press and hold for 3 seconds to turn on/o the doorbell.
• Never touch the product with wet hands.
• Do not disassemble, repair or modify the product.
• Do not use the device where wireless devices are not allowed.
• Do not use the product if the casing has been broken. Danger
of electric shock.
• Keep the device away from re or hot environments. DO NOT
immerse in water or any other liquid.
• The product can only be installed, disassembled and
maintained by instructed person or skilled person.
• Do not place near automatically controlled devices such as re
alarms. Radio waves emitted from this product may cause such
devices to malfunction resulting in an accident.
• Observe restrictions on using wireless products in fuel depots,
chemical plants or when blasting operations are in progress.
• Do not use liquid to clean the product. Only use a dry cloth.
• Never put metal objects inside the product. If a metal object
enters the product, turn o the circuit breaker and contact an
authorised electrician.
• This product is not intended to be used when providing medical
care. Consult the manufacturer of any personal medical devices,
such as pacemakers or hearing aids to determine if they are
adequality shielded from external RF (radio frequency) energy.
• Do not use this product in health care facilities. Hospitals or
health care facilities may be using equipment that could be
sensitive to external RF energy.
• Do not use this product near water for example near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement or near
a swimming pool.
• The product should be kept free from excessive smoke, dust
TP-Link hereby declares that the device is in compliance with the
essential requirements and other relevant provisions of directives
2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The
original EU declaration of conformity may be found at
https://www.tapo.com/support/ce/
TP-Link hereby declares that the device is in compliance with the
essential requirements and other relevant provisions of the Radio
Equipment Regulations 2017. The original UK declaration of
conformity may be found at https://www.tapo.com/support/ukca/
CAUTION!
Avoid replacement of a battery with an incorrect type that can
defeat a safeguard.
Avoid disposal of a battery into re or a hot oven, or
mechanically crushing or cutting of a battery, that can result in
an explosion.
Do not leave a battery in an extremely high temperature
surrounding environment that can result in an explosion or the
leakage of îž°ammable liquid or gas.
Do not leave a battery subjected to extremely low air pressure
that may result in an explosion or the leakage of îž°ammable
liquid or gas.
Doorbell LED Indication
Doorbell updating
Doorbell resetting
Ready for setup
Connecting to Wi-Fi
Connected to the cloud
Blinking red and green
Solid red
Blinking white quickly
Blinking red quickly
Blinking red slowly
Solid white
Solid amber Connected to Wi-Fi
Starting up
Charging the doorbell
Blinking amber quickly
for 3 seconds
Chime LED Indication
Blinking red and green
Blinking red slowly
Solid green
Solid red
Blinking green quickly
Solid amber
Starting up
Connected to the cloud
Ready for setup
Connecting to Wi-Fi
Connected to Wi-Fi
Chime updating
Please read and follow the above safety information when
operating the device. We cannot guarantee that no accidents or
damage will occur due to improper use of the device. Please use
this product with care and operate at your own risk.
For EU/UK Region:
Operating Frequency / Max Output Power:
2400MHz~2483.5MHz / 20dBm
or high temperature and vibration.
• This product should not be exposed to direct sunlight.
• Do not place heavy objects on top of the product.
• This product may interfere with other electronic products such
as TV, radios, personal computers, phones or other wireless
devices.
• This equipment can be powered only by equipment that
complies with Power Source Class 2 ( PS2) or Limited Power
Source(LPS) dened in the standard of IEC 62368-1.
• This equipment shall be installed at a height of fewer than 2
meters when sticking to a clean wall.
• Doorbell Operating Temperature: -20 °C ~ 45°C (-4°F ~ 113°F)
Chime Operating Temperature: 0 °C ~ 40°C (32°F ~ 104°F)
?
Need some help?
Visit https://www.tapo.com/support/
for technical support, the user guide, FAQs,
warranty & more
7
Anti-Theft Button
9
• Press and hold for 5s:
Pause the alarm (Continues to alarm when released)
• Press and hold simultaneously for 10s:
Disable the anti-theft alarm feature
When the Anti-Theft Alarm is enabled on the Tapo app, an
alarm will trigger once the doorbell is removed.
3. Mount the doorbell to the bracket.
Note: If the wires are too short, use the included extension
wires and wire nuts to make them longer.
If the wires are too short:
Requires:
• Video Doorbell Camera
• (Optional) Extension Wires ×2, Wire Nuts ×2
Option B: Hardwire Powered
Connect the wires to the doorbell and tighten the
screws. Mount the doorbell to the bracket and turn on
the circuit breaker.
Option A: Battery Powered
Mount the doorbell to the bracket.
Requires:
• Video Doorbell Camera
Note: If you have trouble attaching the doorbell to the bracket or it causes false anti-theft alarms, check if you tightened the
screws too much that the bracket bent. Adjust the depth of the screw and then reinstall the doorbell.
UP
UP
©2024 TP-Link


Product specificaties

Merk: TP Link
Categorie: Bewakingscamera
Model: Tapo D235

Heb je hulp nodig?

Als je hulp nodig hebt met TP Link Tapo D235 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Bewakingscamera TP Link

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera