Tiptop Audio uZeus 4HP Handleiding

Tiptop Audio Niet gecategoriseerd uZeus 4HP

Lees hieronder de 📖 handleiding in het Nederlandse voor Tiptop Audio uZeus 4HP (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 224 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/5
TM
ZEUS Series:
microZEUS with
Flying Bus Boards
TM
Zeus Series: microZEUS with Flying Bus Boards
The uZEUS is a 4HP power supply module for Eurorack format synthesizers.
This version comes with two (2) ying bus boards that are already attached to
the module. An additional connection is available on the uZEUS for attaching
an extra ying bus board if needed. The ying bus boards use a keyed
connector, ensuring that module power cables can only be connected in the
correct position.
When ordering your uZeus make sure to order a power adapter that ts your
country’s power plug. These adapters are usually oered along side the uZeus
by the shops carrying them in your country.
Connecting the uZEUS:
First, attach your uZEUS to your system. It can be placed in any position along
the rails, but it is strongly recommended that it be placed on the rightmost
edge of your case.
Next, plug the wall adapter in to your mains supply and insert the barrel plug
into the uZEUS. Once connected, turn the switch to the ‘ON’ position and make
sure all three (3) blue lights are illuminated.
If for any reason, one or all of them are not illuminated then immediately turn
the switch to the ‘OFF’ position.
Check all of your connections before continuing. Is the uZEUS in contact with
another object? Are all of the modules plugged in properly?
Once you have successfully powered your uZEUS, all you have left to do now
is play!
It is important to note that the front panel of the uZEUS may get very warm.
Please do not be alarmed as this is normal and is part of the standard operation
of the uZEUS, more on that in the next pages, please continue reading.
WARNING: The internal components of the uZEUS can get
very hot. Do not touch the internal components while the
uZEUS is connected and/or powered.
TM
Zeus Series: microZEUS with Flying Bus Boards
Tiptop Audio has the following recommendations for connecting your
modules and using your uZEUS:
The uZEUS is designed to power systems ranging from 3U to 6U of 84HP of
mixed analog and digital modules. As you keep adding modules to your system
beyond 3U x 84HP we recommend a simple test that will help you protect your
uZeus and adapter from mistakenly getting overloaded and eventually failing.
To do so check the heat of your uZeus face plate and the power adapter roughly
10 minutes after power up. If they become almost too hot to the touch then you
are overloading one of them and this will cause them to fail. Please remove a few
modules and test again, repeating until they are reasonably but not burning hot.
Please note: the uZeus was designed to be mounted on metal rails with good
heat transfer such as Tiptop Z-Rails. Do not install the uZeus directly to wood or
any other ammable material, this will cause the uZeus to overheat.
To insure long life for the power supply, you should be aware of the total power
consumption of your system. This is determined by adding together the amount
of current used by each of your modules. Please refer to the power consumption
gures provided by your modules’ manufacturer(s). Please note, digital modules
are usually by far more demanding than analog modules.
To avoid crosstalk, it is recommended that High current-drawing modules like
digital and DSP modules, VCOs and sound/noise generators should not all be
plugged into a single bus board. For modules that are placed next to the uZEUS
and have more than one circuit board and may block the ying bus boards, take
advantage of the ribbon cables exibility and route it around the module. The
bus boards were designed with this consideration in mind.
Wall Adapter Information:
The Tiptop wall adapter supplied with the Happy Ending kit is rated 1000mA and
must be kept at that limit, it is a starter power supply and is not meant for
powering large systems beyond a Happy Ending Kit. Higher power adapters can
be used as long as you carefully keep checking how hot the uZeus
face plate gets as recommended above. The uZeus uses
15VDC adapters with 2.5mm barrel jack center pin positive.

Product specificaties

Merk: Tiptop Audio
Categorie: Niet gecategoriseerd
Model: uZeus 4HP

Heb je hulp nodig?

Als je hulp nodig hebt met Tiptop Audio uZeus 4HP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Tiptop Audio

Tiptop Audio

Tiptop Audio Z2040 LP-VCF Handleiding

3 Augustus 2023
Tiptop Audio

Tiptop Audio HATS909 Handleiding

5 Mei 2023
Tiptop Audio

Tiptop Audio Z4000 Handleiding

18 April 2023
Tiptop Audio

Tiptop Audio SD909 Handleiding

13 April 2023
Tiptop Audio

Tiptop Audio MISO Handleiding

2 April 2023
Tiptop Audio

Tiptop Audio ModFX Handleiding

9 Maart 2023
Tiptop Audio

Tiptop Audio MIXZ Handleiding

2 Maart 2023
Tiptop Audio

Tiptop Audio CP909 Handleiding

28 Februari 2023
Tiptop Audio

Tiptop Audio FSU Handleiding

27 Februari 2023
Tiptop Audio

Tiptop Audio Fold Processor Handleiding

17 Februari 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Inglesina

Inglesina Welcome Pad Handleiding

22 December 2024
Inglesina

Inglesina Front Handleiding

22 December 2024
Inglesina

Inglesina Newborn Winter Muff Handleiding

22 December 2024
Inglesina

Inglesina Stroller Winter Muff Handleiding

22 December 2024
Protector

Protector AS-5030.3 V2 Handleiding

21 December 2024
Sabrent

Sabrent AU-MMCW Handleiding

21 December 2024
Sabrent

Sabrent AU-2X35 Handleiding

21 December 2024
Sabrent

Sabrent CB-RS232 Handleiding

21 December 2024
Owon

Owon 500W Handleiding

21 December 2024
Owon

Owon 300W Handleiding

21 December 2024