Theben theLuxa S150 BK Handleiding

Theben Bewegingsdetector theLuxa S150 BK

Lees hieronder de 📖 handleiding in het Nederlandse voor Theben theLuxa S150 BK (4 pagina's) in de categorie Bewegingsdetector. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

theLuxa S150 WH 1010500

theLuxa S150 BK 1010501

theLuxa S180 WH 1010505

theLuxa S180 BK 1010506

309691 01

Motion detector

1. Essential safety instructions

Danger of death through electric shock or fire!

 Installation should only be carried out by a pro-

fessional electrician!

WARNING

•The device conforms with EN 60669-2-1 when correctly

installed

•IP 55 in accordance with EN 60529

Designated use

•Motion detector for automatic lighting control dependent

on presence and brightness

•Suitable for installation on external walls

•Suitable for entrances, garages, gardens, corridors, parks,

etc.

•Only intended for installation outside of arm‘s reach

Disposal

Dispose of the motion detector in an environmentally sound

manner (electronic waste)

2. Description

2 potentiometers

for setting time

(min) and bright-

ness (lux)

Motion detector

with sensor head

3. Connection

WARNING

Danger of death through electric shock!

 Disconnect power source!

 Cover or shield any adjacent live components.

 Ensure device cannot be switched on again!

 Check power supply is disconnected!

 Earth and bypass!

The device can be manually activated with a circuit breaker.

After releasing the button (return of power) the device swit-

ches on (for at least 40 secs or for the time set on the device).

4. Installation

 If applicable, use optional corner bracket (9070902,

9070903) or spacer frame (9070906, 9070907) for exible

installation as well as cable insertion from side or top/

bottom.

230V

 Disconnect power source.

 Make marks for the holes on the wall (with en-closed drill

template/base).

 Drill holes.

6 mm

60 mm

 Feed cable through the seal of the base.

 Fasten base (and spacer frame) to the wall.

brown

Phase

Switched

phase

Neutral

conductor

Neutral

conductor

Earthing

conductor

Earthing

conductor

blue

green/yellow

 Connect the individual wires to the appropriate terminal.

 Tighten screws.

Click!Click!

 Plug motion detector into base and click in.

 Connect motion detector to power supply.

Dismantling

 Using the screwdriver, carefully loosen the snap-in hook at

the side and pull the device forward.

Installation instructions

As the detector reacts to variations in temperature, avoid the

following situations:

 Do not direct motion detectors at objects with highly reec-

tive surfaces such as mirrors etc.

 Do not install motion detectors near heat sources such as

heating outlets, air conditioning systems, lamps etc.

 Do not direct the motion detector at objects that turn in the

wind such as curtains, large plants etc.

 Take account of motion direction during test run.

3 m

5 m

12 m

150°

6 m

3 m

5 m

12 m

180°

6 m

•Recommended installation height: 2 – 4 m

•Crosswise detection area: 12 m (crosswise to the detector)

•Frontal detection area: 5 m (in front of the detector)

•Detection angle: 150°/180°

5. Direction test and alignment

The walk test is used to test the detection range and to res-

trict it if necessary.

 Set the potentiometer time (min) to test.

The motion detector now only reacts to movement (indepen-

dent of brightness).

 Crosswise to the detection area. After the motion detector

has detected a movement, it switches on for 2 s.

 Note direction of motion during the test.

Sec

2 sec

Test

210

30s

test

min

Align motion detector with sensor head

The sensor head can be turned by 30° downwards and

by 90° to left and right.

30˚

90 90

6. Setting

The motion detector has two potentiometers underneath for

setting the time (min) and brightness (lux).

15 100

lux

210

30s

test

min

Set brightness (lux)

You can set different brightness values (lux) with the

potentiometer.

If you want to change the preset brightness (15 lux default)

 Set potentiometer to desired brightness (5 – 1000 lux).

15 100

lux

teach-in 1000 Lux

5 Lux 500 Lux

7 Lux 100 Lux

10 Lux

15 Lux

50 Lux

15 Lux

or want a specic brightness value to be learned using the

teach-in function

 At the desired brightness set the potentiometer to . The

value will be learned after 15 s.

 Leave potentiometer at position .

Set time (min)

If the motion detector detects no further movement, it swit-

ches off after the set time.

If you want to change the preset time (2 min default)

 Set potentiometer to desired time (0.5 s – 20 min).

210

30s

test

min

test 20 min

1 s 15 min

30 s 10 min

1 min

2 min

5 min

2 min

If you want to use the pulse function (e.g. for a staircase light

time switch)

 Set potentiometer to position . The motion detector

is switched on for < 1 s, then off for 9 s. If it detects a

movement again, it switches on again for 1 s.

7. Caractéristiques techniques

• Operating voltage: 230 V AC, +10 % –15 %

• Frequency: 50 Hz

• Standby: < 1 W

• Detection angle: 150°/180°

• Detection area: crosswise: max. 12 m,

frontal: max. 5 m

• Installation height: 2 – 4 m

• Creep under protection: yes

• Brightness setting range: 5–1000/∞ lux

• Switching period range: 5 s – 20 min

• Permissible ambient temperature: –25 °C to +45 °C

• Protection class: II

• Protection rating: IP 55 in accordance with

EN 60529

• Switching capacity: 10 A (cos = 1)ϕ

6 A (cos ϕ = 0.6)

3 AX (cos ϕ = 0.3)

• Min. switching capacity: 10 mA

• Switching contact: μ-Contact 230 V AC

• LED lamps <2 W 25 W

• LED lamps >2 W <8 W 90 W

Product specificaties

Merk:	Theben
Categorie:	Bewegingsdetector
Model:	theLuxa S150 BK
Kleur van het product:	Zwart
Breedte:	85 mm
Diepte:	127 mm
Hoogte:	99.6 mm
Internationale veiligheidscode (IP):	IP55
Plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Montagewijze:	Muur
Type stroombron:	AC
Stroomverbruik (in standby):	0.9 W
Type beeldsensor:	Passieve infraroodsensor (PIR)
Ingangsspanning:	230 V
Frequentie:	50 Hz
Bedrijfstemperatuur (T-T):	-25 - 45 °C
Test knop:	Ja
Detectie hoek:	150 °
Installatie hoogte (min):	2 m
Installatie hoogte (max):	4 m
Lichtgevoeligheid:	5 Lux