Techly IDATA EXTIP-329 Handleiding

Techly AV extender IDATA EXTIP-329

Lees hieronder de 📖 handleiding in het Nederlandse voor Techly IDATA EXTIP-329 (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Features

1 . Applies advanced HDbitT over IP technology

2 . Transmits HDMI signal over any simple 2 conductor cables, it could be

network cable, power line, coaxial cable, telephone wire etc

3 . Supported resolution is up to full HD 1080p@60Hz

4 . Transmission distance is up to 300 meters

5 . IR passback for controlling the transmitter side source signal easily

from the receiver side

6 . Supports bi-directional RS232 pass back

7 Supports one way HDMI loop output .

8 . Plug and play, easy for installation

9 Supports multicast that one transmitter unit is capable of driving up .

to 4 receiver units

Package Content

1. HDMI source device(computer graphics card, DVD,PS3, HD

monitoring equipment etc)

2. HDMI display device like SDTV, HDT V, projector with HDMI port

3. Any 2 conductor cables,like:network cable, power line, coaxial cable,

telephone wire etc.

Installation Requirements

1. HDMI EXTENDER TX (Transmitter)

Panel Description

Thank you for purchasing this product. For optimum performance

and safety, please read the instructions carefully and keep the manual

for future reference. Please read below safety instructions carefully

before installation and operation:

1.Please pay attention to all the warnings and hints on this device.

2.Do not expose this unit to rain, moisture and liquid.

3.Do not put any stuff into the device.

4 '.Do not repair or open this device without professional people s

guidance.

5.Make sure good ventilation openings to avoid product overheating

damage.

6.Shut off power and make sure environment is safe before installation.

7.Do not plug-in/out the connected cables when it is in using.

8.Make sure the specification matched if using 3rd party DC adapters.

Important Safety Instruction

Product Introduction

This Extender transmits and receive HDMI signal over any simples

2 conductor cable , such 2 conductor cable c be network cable, s s an

power line, coaxial cable, telephone wire etc. This extender includes a

transmitter unit and a receiver unit, transmission distance is up to 300

meters. It supports multicast that one transmitter unit is capable of

driving up to 4 receiver units using either 4 individual wire pairs over

300m each, or daisy chaining the receivers. IR passback for control ing

the transmitter side source signal easily from the receiver side. In

additional, i with RS232 serial port that support it s s bi-directional RS232

pass back e .This product is wid ly used in home theater system, media

projects, entertainment and exhibition center.

IR O UT IR I N

IR blaster extensio n

cable x1pcs

IR recei ver extension

cable x1pcs

DC12V/2 RS232 serial por t A ×2pcs

cap × 2pcs

Term inal Po t( r Any 2 conductor)

Power i nput（DC12V）

Bi- directionl pass backRS232

IR signal output to connect

with bla ster extensi on ca ble

HDMI signal output

HDMI signal inp ut

Data tra nsm ission light

Network link light

Reset button

2. HDMI EXTENDER RX(Receiver)

Term inal Post( Any 2 conductor)

Power i nput（DC12V）

IR signal input to co nnect with

IR recei ver extension ca ble

HDMI signal output

Data tra nsm ission light

Network link light

Reset button

Connections

1. Unicast configuration: Up to 30 meters transmission distance over

Any 2 conductor cables

2. Multicast configuration: one transmitter to four receivers,realize

extender & splitter funtion

Connection instruction

1 ) Connect source device to Transmitter unit (TX), and display

.device to Receiver unit (RX) via HDMI cables

2 Connect Transmitter unit (TX) and Receiver unit (RX) via any )

2 conductor cable.

3 Plug the power supply to Transmitter unit and Receiver unit (RX). )

2 4

HD MI OU T

Any 2 conduct or

cab les

13 5 67

2 4

HDMI EXT ENDER

Tra nsm itter ×1pcs

HDMI EXT ENDER

Receiver ×1pcs

User Manua l × 1pcs

Any 2 conductor

cables

HD MI OU T

HD MI IN

Tra nsm itt er

Re cei ver

Tra nsm itt er

Bi- directionl pass backRS232

GND

TXD

RXD

line

IR User Guide

1 ) IR blaster extension cable should plug-in the IR-out port of

transmitter of HDMI extender, and the IR receiver extension cable

.should plug-in the IR-out port of the receiver of HDMI extender

2 ) The emitter of IR blaster should be as close as possible to the IR

receiver of the signal source device.Using the IR remote controller

of the signal source device towards the IR receiver (connected to

the RX of HDMI extender), to remote control source media playback .

1 ) Different encoding mechanism can not mix-connect, the baud rate

of RS232 serial of these transmitter unit and receiver unit, suppor t

.2400,4800, 9600, 19200, 28800, 38400, 57600, and 115200

2 Line order )

Check and make sure the RS23S serial line connect firmly and well,

and make sure serial data line is connected correctly as below:

If the RS232 serial does not work by following above connection,

please try to change the order of TXD line and RXD line.

Q: TV display “Waiting for connection” on the right corner?

A: Please check if the power supply of transmitter and switcher (if used)

is connected, and make sure connecting cable is firmly.

Q: TV display “Please check the transmitter input signal”？

A: 1 ) please check if there is a HDMI signal input of transmitter.

2 ) Try to connect the signal source directly to display device to see if

there is singal output from source device or change the signal

source, HDMI wire and try again.

Q Display not fluent, not stable?：

A 1 ) Please check the cable length between the transmitter to the ：

receiver the required range, make sure connecting cable is well

and Without interference.

2 ) Press "reset" button on the transmitter/receiver front panel, reset

and reconnect.

FAQ

3 ) Check baud rate

If you need to check the baud rate at last time, firstly, before power

on, set the baud rate to 115200 on your serial port test tool . Then,

power on, when the RS232 serial of product connects to serial port

test tool, the software will read out the baud rate at present.

e.g.: software show information “ Baud rate: 9600”, means 9600 is

the current baud rate.

4 ) Set baud rate

For example: the current baud rate is 9600, but the baud rate of

control equipment is 19200, so it needs to set the baud rate to

9600. At this time, in serial port tool, choose baud rate "9600", then

input command "set: 19200" in character format and send it out.

HDbitT HDMI Extender over Any Two

Conductor Cables

User Manual

Specification

HDMI Signa l

Su ppor t resolutions

A udi o format

Transm is si on di stance

I R sign al

Item s Specifications

HDMI1.3, Compatible with HDCP1.3

480i@60Hz, 4 80p@6 0Hz , 576i@50Hz, 576p@50Hz,

720p@5 0/60Hz, 1080i @50 /60Hz, 1080p@50/ 60Hz

PCM

Transmission dista nce is up to 300 meters.

Supports 20~ 60KHz I R devic es

Wo rkin g Tem perature

Power Sup pl y

Power Consumption

D imensio ns

RS232

DC12V/2A

0℃～60℃

TX: 7.5W; RX: 7W

Supports Bi-dire ctional RS 232 p ass back

We ight

Color Black

228(L)x125.4(W)x25(H)mm

210g*2pcs

Storage temperature

-20 70～ ℃

Networ k ba ndwidth 18M bps

Disclaimer

The product name and brand name may be registered trademark of

related manufacturers.TM and ® may be omitted on the user manual.

The pictures on the user manual are just for reference,and there may be

some slight difference with the real products.

We reserve the rights to make changes without further notice to a

product or system described herein to improve reliability, function or

design.

Product specificaties

Merk:	Techly
Categorie:	AV extender
Model:	IDATA EXTIP-329
Kleur van het product:	Zwart
Gewicht:	210 g
Soort:	AV-zender & ontvanger
Ondersteunde video-modi:	480i, 480p, 720p, 1080i, 1080p
Maximum resolutie:	1920 x 1080 Pixels
HDCP:	Ja
HDMI versie:	1.3
HDMI in:	1
Afmetingen (B x D x H):	228 x 126 x 25 mm
Aantal HDMI-uitgangen:	1
Maximaal bereik:	300 m
Stroomverbruik (zender) (max):	7.5 W
Stroomverbruik (ontvanger) (max):	7 W