Tanaka TCS 40EA Handleiding

Tanaka Zaagmachine TCS 40EA

Lees hieronder de 📖 handleiding in het Nederlandse voor Tanaka TCS 40EA (69 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/69
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this
manual BEFORE operating the power tool. Please keep this manual available for other users and owners
before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation de cet outil motorisé peut entraîner la mort ou de INCORRECTE OU DANGEREUSE
sérieuses blessures corporelles !
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière de
lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi à la
disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi
doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización de esta herramienta eléctrica puede provocar lesiones INAPROPIADA O PELIGROSA
graves o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este
manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras
personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.
Model
Modèle
Modelo TCS 40EA Chain Saw
Tronçonneuse
Motosierra
Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
2
English
WARNING
The engine exhaust from this product contains
chemical known to the State of California to cause
cancer, birth defects or other reproductive harm.
SAFETY PRECAUTIONS FOR CHAIN
SAW USERS
Kickback safety precautions
WARNINGS! : Kickback may occur when the nose
or tip of the guide bar touches an object, or when
the wood closes in and pinches the saw chain in
the cut. Tip contact in some cases may cause a
lightning-fast reverse reaction, kicking the guide bar
up and back toward the operator. Pinching the saw
chain along the top of the guide bar may push the
guide bar rapidly back toward the operator. Either of
these reactions may cause you to lose control of the
saw, which could result in serious personal injury.
Do not rely exclusively upon the safety devices built
into your saw. As a chain saw user, you should take
several steps to keep your cutting jobs free from
accident or injury. ( Fig.1)
1
Fig. 1
○
With a basic understanding of kickback, you
can reduce or eliminate the element of surprise.
Sudden surprise contributes to accidents.
○
Keep a good fi rm grip on the saw with both
hands, the right hand on the rear handle and the
left hand on the front handle, when the engine is
running. Use a fi rm grip with thumbs and fi ngers
encircling the chain saw handles. A fi rm grip will
help you reduce kickback and maintain control of
the saw. Don't let go.
○
Make sure that the area in which you are cutting
is free from obstructions. Do not let the nose
of the guide bar contact a log, branch, or any
other obstruction that could be hit while you are
operating the saw.
○
Cut at high engine speeds.
○
Do not overreach or cut above shoulder height.
○
Follow the manufacturer's sharpening and
maintenance instructions for the saw chain.
○
Only use replacement bars and chains specifi ed
by the manufacturer or the equivalent.
Other safety precautions
○
Do not operate a chain saw with one hand!
Serious injury to the operator, helpers,
bystanders, or any combination of these persons
may result from one-handed operation. A chain
saw is intended for two-handed use.
○
Do not operate a chain saw when you are fatigued.
○
Use safety footwear, snug-fi tting clothing,
protective gloves, and eye, hearing, and head
protection devices.
○
Use caution when handling fuel. Move the chain
saw at least 10 feet (3 m) from the fueling point
before starting the engine.
○
Do not allow other persons to be near the chain
saw when starting or cutting with the chain saw.
Keep bystanders and animals out of the work area.
○
Do not start cutting until you have a clear work
area, secure footing, and a planned retreat path
from the falling tree.
○
Keep all parts of your body away from the saw
chain when the engine is running.
○
Before you start the engine, make sure that the
saw chain is not contacting anything.
○
Carry the chain saw with the engine stopped,
the guide bar and saw chain to the rear, and the
muffl er away from your body.
○
Do not operate a chain saw that is damaged,
improperly adjusted, or not completely and
securely assembled. Be sure that the saw chain
stops moving when the throttle control trigger is
released.
○
Shut off the engine before setting the chain saw
down.
○
Use extreme caution when cutting small-size
brush and saplings because slender material
may catch the saw chain and be whipped toward
you or pull you off balance.
○
When cutting a limb that is under tension, be
alert for springback so that you will not be struck
when the tension in the wood fi bers is released.
○
Keep the handles dry, clean, and free of oil or
fuel mixture.
○
Operate the chain saw only in well-ventilated
areas.
○
Do not operate a chain saw in a tree unless you
have been specifi cally trained to do so.
○
All chain saw service, other than the items
listed in the instruction manual(s) maintenance
instructions, should be performed by competent
chain saw service personnel. (For example, if
improper tools are used to remove the fl ywheel or
if an improper tool is used to hold the fl ywheel in
order to remove the clutch, structural damage to
the fl ywheel could occur and subsequently could
cause the fl ywheel to burst.).
○
When transporting your chain saw, use the
appropriate guide-bar scabbard.
English
3
MEANINGS OF SYMBOLS
NOTE: Some units do not carry them.
Symbols
WARNING
The following show symbols used for the machine. Be sure that you understand their meaning
before use.
It is important that you read, fully
understand and observe the following
safety precautions and warnings.
Careless or improper use of the unit may
cause serious or fatal injury.
Emergency stop
Read, understand and follow all warnings
and instructions in this manual and on the
unit.
Fuel and oil mixture
Always wear eye, head and ear protectors
when using this unit. Chain oil fi ll
Warning, kickback danger. Be careful of
possible sudden and accidental upward
and/or backward motion of the guide bar.
Carburetor adjustment - Idle speed
One-handed usage not permitted. While
cutting, hold saw fi rmly with both hands
with thumb fi rmly locked around front
handle.
Carburetor adjustment - Low speed
mixture
Chain brake Carburetor adjustment - High speed
mixture
Choke Oil pump adjustment
On/Start Priming pump
Off /Stop Computed kickback angle (CKA) without
a chain brake
Contents
WHAT IS WHAT?...................................................4
WARNINGS AND SAFETY INSTRUCTIONS ....... 5
SPECIFICATIONS ................................................. 7
ASSEMBLY PROCEDURES ................................. 8
OPERATING PROCEDURES ............................... 9
MAINTENANCE .................................................. 15
Parts breakdown

Product specificaties

Merk: Tanaka
Categorie: Zaagmachine
Model: TCS 40EA

Heb je hulp nodig?

Als je hulp nodig hebt met Tanaka TCS 40EA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Tanaka

Tanaka

Tanaka TCS-3351PFS Handleiding

18 Augustus 2023
Tanaka

Tanaka TCS27EPAP Handleiding

18 Augustus 2023
Tanaka

Tanaka TCS-3301PFS Handleiding

18 Augustus 2023
Tanaka

Tanaka TCS33EDTP Handleiding

18 Augustus 2023
Tanaka

Tanaka TCS 51EAP Handleiding

1 Augustus 2023
Tanaka

Tanaka TCS 3401S Handleiding

1 Augustus 2023
Tanaka

Tanaka TCS 33EDTP Handleiding

1 Augustus 2023
Tanaka

Tanaka ECV-3801 Handleiding

1 Augustus 2023
Tanaka

Tanaka TCS 33EDT Handleiding

1 Augustus 2023
Tanaka

Tanaka TCS 33ED Handleiding

1 Augustus 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Makita

Makita DJR187ZK Handleiding

2 December 2024
Fieldmann

Fieldmann FDK 201302-E Handleiding

1 December 2024
Fieldmann

Fieldmann FDP 200805-E Handleiding

1 December 2024
Fieldmann

Fieldmann FZP 4216-B Handleiding

1 December 2024
Fieldmann

Fieldmann FZP 5816-B Handleiding

1 December 2024
King Craft

King Craft ZKGS 4300 UG Handleiding

30 November 2024
Global

Global PSG 750 Handleiding

30 November 2024
Global

Global MTS-G 400 Handleiding

30 November 2024
Global

Global N-PSL 750 Handleiding

30 November 2024
Global

Global PSL-G 750 Handleiding

30 November 2024