Tanaka TCS 33ED Handleiding

Tanaka Zaagmachine TCS 33ED

Lees hieronder de 📖 handleiding in het Nederlandse voor Tanaka TCS 33ED (20 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/20
Chain Saw
Model TCS 33ED
Handling instructions
Note:
Before using this machine, carefully read through these HANDLING INSTRUCTIONS
to ensure effi cient, safe operation. It is recommended that these INSTRUCTIONS be
kept readily available as an important reference when using this machine.
2
MEANINGS OF SYMBOLS
NOTE: Some units do not carry them.
Symbols
WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.
It is important that you read, fully understand and
observe the following safety precautions and
warnings. Careless or improper use of the unit may
cause serious or fatal injury.
Emergency stop
Read, understand and follow all warnings and
instructions in this manual and on the unit. Fuel and oil mixture
Always wear eye, head and ear protectors when using
this unit. Chain oil fi ll
Warning, kickback danger. Be careful of possible
sudden and accidental upward and/or backward
motion of the guide bar.
Carburetor adjustment - Idle speed
One-handed usage not permitted. While cutting, hold
chain saw fi rmly with both hands with thumb fi rmly
locked around front handle.
Carburetor adjustment - Low speed mixture
Chain brake Carburetor adjustment - High speed mixture
Choke - Run position (Open) Priming pump
Choke - Start position (Closed)
4
Guaranteed Sound power level
On/Start Hot surface
Off /Stop Oil pump adjustment
Contents
WHAT IS WHAT? .............................................................................. 3
WARNINGS AND SAFETY INSTRUCTIONS .................................. 4
SPECIFICATIONS ............................................................................ 6
ASSEMBLY PROCEDURES ............................................................. 7
OPERATING PROCEDURES ........................................................... 8
MAI NT ENA NCE .............................................................................. 12
Parts breakdown
3
WHAT IS WHAT?
1. Throttle lever: Device activated by the operatorʼs fi nger, for
controlling the engine speed.
2. Throttle lever lockout: Device that prevents the accidental
operation of the throttle lever until manually released.
3. Stop switch: Device for allowing the engine to be started or
stopped.
4. Oil tank cap: For closing the oil tank.
5. Recoil starter: Pull handle to start the engine.
6. Front handle: Support handle located at or towards the front of
the engine housing.
7. Fuel tank cap: For closing the fuel tank.
8. Rear handle: Support handle located at or towards the rear of the
engine housing.
9. Choke lever: Device for enriching the fuel/air mixture in the
carburetor, to aid starting.
10. Priming pump; Device for supplying extra fuel, to aid starting.
11. Guide bar: The part that supports and guides the saw chain.
12. Saw chain: Chain, serving as a cutting tool.
13. Chain brake (Front hand guard): Device for stopping or locking
the chain.
14. Chain catcher: device for restraining the saw chain.
15. Air fi ler cover: Cover for air fi lter and carburetor.
16. Side case: Protective cover to the guide bar, saw chain, clutch
and sprocket when the chain saw is in use.
17. Tension adjustment bolt: Device, often acting on the guide bar,
for adjusting the saw chain tension.
18. Chain oil adjusting screw: Device for adjusting the delivery of
saw chain oil to the guide bar and the saw chain.
19. Muffl er: Reduces engine exhaust noise and directs the exhaust
gases.
20. Anti-vibration spring: Reduce the transmission of vibrations to
the operator's hands.
21. Anti-vibration rubber: Reduce the transmission of vibrations to
the operator's hands.
22. Chain bar clamp nut: Secures the side case and the guide bar.
23. Spiked bumper: Device for acting as a pivot when in contact with
a tree or log.
24. Guide bar cover: Device for covering the guide bar and saw
chain when the unit is not being used.
25. Combi box spanner: The tool for removing or installing a spark
plug and tensioning the saw chain.
26. Handling instructions: Included with unit. Read before operation
and keep for future reference to learn proper, safe techniques.
27. Hot surface caution label: Label for caution to hot surface.
26
23
24 25
1
20
8
2110
4
7
3
5
2
6
9
27 18
15
13
22 12
11
19
21 23
14
17
16
20

Product specificaties

Merk: Tanaka
Categorie: Zaagmachine
Model: TCS 33ED

Heb je hulp nodig?

Als je hulp nodig hebt met Tanaka TCS 33ED stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Tanaka

Tanaka

Tanaka TCS-3351PFS Handleiding

18 Augustus 2023
Tanaka

Tanaka TCS27EPAP Handleiding

18 Augustus 2023
Tanaka

Tanaka TCS-3301PFS Handleiding

18 Augustus 2023
Tanaka

Tanaka TCS33EDTP Handleiding

18 Augustus 2023
Tanaka

Tanaka TCS 51EAP Handleiding

1 Augustus 2023
Tanaka

Tanaka TCS 3401S Handleiding

1 Augustus 2023
Tanaka

Tanaka TCS 33EDTP Handleiding

1 Augustus 2023
Tanaka

Tanaka ECV-3801 Handleiding

1 Augustus 2023
Tanaka

Tanaka TCS 33EDT Handleiding

1 Augustus 2023
Tanaka

Tanaka TCS 33ED Handleiding

1 Augustus 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Anova

Anova E60CS Handleiding

20 December 2024
Silverline

Silverline 447132 Handleiding

19 December 2024
Silverline

Silverline 427644 Handleiding

19 December 2024
Herkules

Herkules KS 210 Profi Handleiding

17 December 2024
Total

Total TS730301 Handleiding

16 December 2024
Total

Total TJSLI8501 Handleiding

16 December 2024
Turbo-Silent

Turbo-Silent EKS 2040/1 Handleiding

16 December 2024
Bavaria

Bavaria BJS 400 Handleiding

5 December 2024
Bavaria

Bavaria BCS 64/1 Handleiding

5 December 2024
Bavaria

Bavaria BEC 2040 TC Handleiding

5 December 2024