Swann PRO-T853 Handleiding

Swann Bewakingscamera PRO-T853

Lees hieronder de 📖 handleiding in het Nederlandse voor Swann PRO-T853 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Swann Communications warrants this product against defects in workmanship and material for a period

of one (1) year from its original purchase date. You must present your receipt as proof of purchase for

warranty validation. Any unit which proves defective during the stated period will be repaired without

charge for parts or labour or replaced at the sole discretion of Swann. The end user is responsible for

all freight charges incurred to send the product to Swann’s repair centres. The end user is responsible

for all shipping costs incurred when shipping from and to any country other than the country of origin.

The warranty does not cover any incidental, accidental or consequential damages arising from the use

of or the inability to use this product. Any costs associated with the fitting or removal of this product

by a tradesman or other person or any other costs associated with its use are the responsibility of the

end user. This warranty applies to the original purchaser of the product only and is not transferable to

any third party. Unauthorized end user or third party modifications to any component will render all

warranties void. By law some countries do not allow limitations on certain exclusions in this warranty.

Where applicable by local laws, regulations and legal rights will take precedence.

This equipment has been tested and found to comply with the limits for Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

• Consult the dealer or an experienced radio/TV technician for help

These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. These devices may not cause harmful interference.

2. These devices must accept any interference received, including interference that may cause

undesired operation.

Professional HD

Security Camera

1080p HD Bullet Camera

EN INSTRUCTION MANUAL

Security Made Smarter

Important Note: All jurisdictions have specific laws and regulations relating to the use of cameras.

Before using any camera for any purpose, it is the buyer’s responsibility to be aware of all applicable

laws and regulations that prohibit or limit the use of cameras and to comply with the applicable laws

and regulations.

WARNING: MODIFICATIONS NOT APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD

VOID USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Helpdesk/Technical Support 5 Limited Warranty - Terms & Conditions 6 FCC Verification

tech@swann.com

support.swann.com

USA 1800 627 2799

USA Parts & Warranty 1800 627 2799

(M-F, 9am-5pm US PT)

Australia 1800 788 210

New Zealand 0800 479 266

UK 0808 168 9031

MT853CAMVER1E

250716

Congratulations on your purchase of the Swann 1080p Professional HD Security Camera.

You’ve made a fine choice for keeping a watchful eye over your home or business. The

camera delivers brilliant and amazingly clear high definition images and videos in both day

and nighttime conditions even in complete darkness.

The camera also has an OSD (On-Screen Display) that you can access to change advanced

image settings using the PTZ control interface on your DVR. For details on using the

camera’s OSD feature, download the “ from .T853 OSD Manual” support.swann.com

DVR Compatibility

The camera is compatible with the following Swann 1080p DVR models:

• 4500, 4550, 4575, 4750, 5000 & 8075 Series DVRs

This is not an exhaustive list - since the time of publication we will have released newer

DVRs with which the camera may be supported.

Important Safety Instructions

1. Make sure the camera is fixed correctly and stable if fastened in place.

2. Do not operate if wires and terminals are exposed.

The camera is very flexible, and can be installed almost anywhere. Here are some practical

things to consider when choosing a location:

• Place the camera in a position that a potential security threat will ﬁnd it difﬁcult to

avoid detection. A strategy which is often effective is to monitor entrances and exits -

after all, a security threat has to get in somewhere.

• Ensure the camera is located close enough to what you want to monitor to capture the

required details. For example, if you wish to capture the details of a face, the camera

may need to be located within 15ft (about 5m) of the subject. This is also true if trying

to read printed information - such as a vehicle’s registration plate.

• Mount as high as possible, out of easy reach to prevent tampering. For example, under

the eaves of a roof or high up in protected corners of a wall would be good options.

• Typically, the best view is obtained approximately 7ft (2m) to 10ft (3m) high, looking

slightly downwards.

• While the camera is sealed, robust and able to handle the weather, long-term

exposure to direct sunlight and moisture will eventually cause a degradation in

performance, so if it’s going to be installed outdoors, make sure it’s in a sheltered spot.

• The camera’s night vision will give well-exposed images if the area is dark. However,

if there’s a bright point source in the camera’s view (a streetlight, car headlights or

similar) then it might not engage night vision mode.

The camera can be mounted onto a flat surface using screws. The surface must have

sufficient strength to hold the camera.

• Position the camera in the location you want to mount it, and mark the screw holes

on the surface to position the screws. Then, using appropriate screws for the surface

you’re fixing the camera to, secure the camera into place.

• If you’re mounting to a wooden surface, then screw the camera directly to the surface.

• If you’re mounting to a masonry surface (bricks, concrete or similar), then you’ll need

to use wall plugs.

Aiming the camera

You can use the included allen key to adjust the camera angle.

• To adjust the orientation, loosen the screw indicated by 1.

This enables you to rotate the camera so no matter what

direction it is facing, your images will be the right way up.

• To tilt up and down, loosen the screw indicated by 2.

• To pan left and right, loosen the locking ring indicated by 3.

Be sure to tighten the screws/ring back securely to lock the

camera’s position in place after you’ve finished adjusting the

viewing angle of the camera.

1 3 5 7

2 4 6 8

VIDEO

INPU T

VIDEO

INPU T

VGAVGA

PT ZPT Z

AUDI O

INPU T

AUDI O

INPU T

AUDI O

OUT PU T

AUDI O

OUT PU T 12V12V

LANLAN

Follow the example diagram below to connect the camera to your DVR.

Extension

cable

Digital Video Recorder

Power Power adapter

Video

Tip: Twist to lock

video connectors

1. Connect the camera’s Power and Video cable

to the extension cable’s DC and BNC plugs.

2. Connect the other end of the BNC extension

cable to a video input channel on your DVR.

3. Connect the other end of the DC extension

cable to the power adapter and then plug the

power adapter into a wall outlet. (For multi-

pack cameras, use the power splitter cable

included with the power adapter.)

Note: Images contained in this diagram

are for illustrative purposes only.

2 Choosing a location for your camera1 Welcome 3 Connecting the camera 4 Mounting the camera

Tip: Run cables inside a wall cavity or other protected

enclosure, and ensure that all wiring and the connectors are

suitably insulated and protected from moisture and sunlight.

Product specificaties

Merk:	Swann
Categorie:	Bewakingscamera
Model:	PRO-T853
Kleur van het product:	Wit
Breedte:	61 mm
Diepte:	61 mm
Hoogte:	146 mm
Soort:	CCTV-bewakingscamera
Gebruikershandleiding:	Ja
Materiaal behuizing:	Aluminium
Internationale veiligheidscode (IP):	IP66
Bluetooth:	Nee
Vormfactor:	Rond
Ondersteuning voor plaatsing:	Binnen & buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Plafond
Ondersteunde video-modi:	1080p
Totaal aantal megapixels:	2 MP
Type stroombron:	DC
Stroomuitvoer (volt):	12
Minimale belichting:	- Lux
Aantal cameras:	4
Meegeleverde kabels:	BNC
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
Inclusief AC-adapter:	Ja
Veiligheidsfunties:	Waterbestendig
PTZ control:	Ja
Dag/nacht modus:	Ja
BNC output ports:	1
Montagebeugels meegeleverd:	Ja
Nachtkijker afstand:	30 m
Wifi:	Nee
Bedrijfstemperatuur (T-T):	-20 - 50 °C
Kijkhoek lens, diagonaal:	80 °