StarTech.com ST7C51224 Handleiding

StarTech.com USB Hub ST7C51224

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com ST7C51224 (2 pagina's) in de categorie USB Hub. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Product Diagram (ST7C51224)

Port/LED Function

1USB-A Ports (7)

• Used to charge multiple .Devices

Note: 2A Devices can be charged using a

USB-A (1A) Port 1A Devices, and can be

charged in the however, the USB-A (2A) Port,

charging time will be aected.

2Power LED • Solid red indicates that the is Charging Hub

receiving power.

3 Power Button • Used to turn the On or O.Charging Hub

4DC IN 12V • Used to power the .Charging Hub

7 Port USB Dedicated Charging Station |5 x 1A | 2 x 2A

Requirements

For the latest requirements, please visit .

www.startech.com/ST7C51224

Installation

Notes: The features a chipset that can detect the required charging Charging Hub

mode of a device, and switch to the proper mode for full-speed charging (e.g. If an

Apple device is connected, it will automatically charge to Apple charging mode

specications).

When charging multiple devices, the may become warm to the touch, Charging Hub

this is normal and will not harm the connected .Device(s)

1. Connect the to an and to the Power Adapter AC Electrical Outlet DC IN 12V Port

on the . Charging Hub

2. Press the to turn the On. Wait until the is Power Button Charging Hub Power LED

solid before connecting any devices for charging.

3. Connect your device(s) to the corresponding on the USB-A Port (1A or 2A)

Charging Hub Device(s), according to the charging requirements of the connected :

• 1A:

• Voltage at the common collector (VCC) = 5V

• Ground (GND) = 5V

• D+ = 2.0V

• D- = 2.7V

• 2A:

• Voltage at the common collector (VCC) = 5V

• Ground (GND) = 5V

• D+ = 2.7V

• D- = 2.0V

Installing the Mounting Brackets (Optional)

1. Align the on the with the four Mounting Holes Mounting Bracket Mounting Holes

on the back of the .Charging Hub

2. Insert the (x4) through the and into the Bracket Screws Mounting Bracket

Mounting Holes Charging Hubon the back of the .

3. Tighten the using a , be careful not to Mounting Screws Phillips Head Screwdriver

over-tighten.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

IC Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 0.5cm

between the radiator and your body.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: fr.startech.com

DE: de.startech.com

ES: es.startech.com

NL: nl.startech.com

IT: it.startech.com

JP: jp.startech.com

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

4. Before installing the to the mounting surface, contact a Mounting Bracket

professional. Product mounting should be completed by a certied professional as

per the local safety and building code guidelines.

(Optional) Installing the Rubber Feet

1. Remove the from the .Rubber Feet Adhesive Strip

2. Align each of the on the back of the close to each of the Rubber Feet Charging Hub,

four corners.

3. Remove the adhesive backing and apply the in the desired positions.Rubber Feet

Note: Be careful not to cover the when applying the .Mounting Holes Rubber Feet

Product specificaties

Merk:	StarTech.com
Categorie:	USB Hub
Model:	ST7C51224
Kleur van het product:	Zwart
Gewicht:	126 g
Breedte:	45 mm
Diepte:	110 mm
Hoogte:	24 mm
Gewicht verpakking:	600 g
Breedte verpakking:	98 mm
Diepte verpakking:	235 mm
Hoogte verpakking:	95 mm
Gebruikershandleiding:	Ja
Materiaal behuizing:	Aluminium
LED-indicatoren:	Stroom
Stroom:	1.5 A
Type stroombron:	DC
Inclusief AC-adapter:	Ja
Aantal USB 2.0-poorten:	7
Certificering:	CE, FCC, REACH, RoHS
Materiaal:	Aluminium
Duurzaamheidscertificaten:	RoHS
Ingangsspanning:	100 - 240 V
Temperatuur bij opslag:	-20 - 50 °C
Output current:	5 A
Spanning:	12 V
Ophangsysteem voor aan de muur:	Ja
Type oplader:	Binnen
Lader compatibiliteit:	Universeel
Montagebeugels meegeleverd:	Ja
Stroomverbruik (typisch):	60 W
Bedrijfstemperatuur (T-T):	5 - 35 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Poort 1 uitgangsstroom:	2 A
Poort 2 uitgangsstroom:	1 A