StarTech.com ST121HDBTSC Handleiding

StarTech.com AV extender ST121HDBTSC

Lees hieronder de 📖 handleiding in het Nederlandse voor StarTech.com ST121HDBTSC (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Quick-Start Guide

Manual Revision: 06/20/2018

For the full manual, technical specications, and support for

this product, please visit www.startech.com/ST121HDBTSC.

Packaging Contents

• 1 x HDBaseT Transmitter

• 1 x HDBaseT Scaler Receiver

• 1 x IR Remote Control

• 1 x RJ-11 to RS-232 Adapter

• 1 x CAT5 Cable

• 1 x RJ-11 Cable

• 2 x Sets of Mounting Brackets

• 1 x Universal Power Adapter (NA/JP, EU, UK, ANZ)

• 2 x Sets of Rubber Feet

• 1 x Quick-Start Guide

• 1 x IR Receiver

• 1 x IR Blaster

Requirements

• 1 x Local HDMI Display with Cabling

• 1 x Remote HDMI Display with Cabling

• (Optional Setup) 1 x DisplayPort Video Source with Cabling

• (Optional Setup) 1 x VGA Video Source with Cabling

• (Optional Setup) 2 x HDMI Video Sources with Cabling

Product Diagram

Actual products may vary from photos

Transmitter Front View

1. Selected Port LEDs

2. IR Sensor

3. Output Port LED

4. Input Selection Buttons

5. VGA Input Button/

Function Button 1

6. Function Button 2

7. Output Selection Buttons

Transmitter Rear View

ST121HDBTSC

Multi-Input HDBaseT Extender Switch and Scaler - 1080p

1. DC 12V Power Port

2. IR Out/In Ports

3. HDMI Output Port

4. EDID Copy Button

5. 3.5 mm Audio In Port

6. VGA Input Port

7. DP Input Port

8. Ground

9. (Control) RJ-11 Serial Jack

10. HDBaseT Output Port

11. Auto/Inventory EDID Switch

12. Mode Switch

13. HDMI Input Port #2

14. HDMI Input Port #1

Receiver Front View

1. Input LED (1 - 4)

2. Status LED

3. Enter Button

4. Navigation Buttons

5. Exit Button

6. Menu Button

Receiver Rear View

1. RJ11 Control Port

2. Ground

3. DC 12V Power Port

4. IR In/Out Port

5. Port Link Switch

6. HDBaseT Input Port

7. HDMI Output Port

8. 3.5 mm Audio Out

Port

Installation

Notes: Make sure that the HDBaseT Transmitter and HDBaseT

Receiver are each located near an AC power outlet and that all

devices connected to them are turned o.

1. Set up the video sources (HDMI, DisplayPort and VGA) and

remote display.

2. On the back of the HDBaseT Transmitter, connect each of the

Video Sources (HDMI, DisplayPort and VGA) to the corresponding

input ports (cables sold separately).

1 2 3 4 5 6 7

8 9 10 11 12 13 14

3 4 5 6

2 3 567 8

1 2 3

75 64

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

• If Class 1 Laser Product. Laser radiation is present when the system is open.

• Wiring terminations should not \be made with the product and/or electric lines under power.

• Product installation and/or mounting should be completed by a certied professional as per the local safety and building code guidelines.

• Cables (including power and charging cables) should be placed and routed to avoid creating electric, tripping or safety hazards.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

• Si le produit est Laser de Classe 1, le rayonnement laser est présent lorsque le système est ouvert.

• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit et/ou les câbles électriques sont sous tension.

• L’installation et/ou le montage du produit doit être réalisé par un professionnel certié et dans le respect des normes locales et du code de construction local.

• Les câbles (y compris les câbles d’alimentation et de chargement) doivent être placés et acheminés de façon à éviter tout risque électrique, de chute ou de sécurité

Pour consulter les manuels, les vidéos, les FAQ, les contrôlleurs, les téléchargements, et plus encore, visitez: www.StarTech.com/fr/support-produit.

安全対策

• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

• クラス1レーザー製品では、システムが開放状態の場合、レーザー光が照射されています。

• 電源が入っている状態の製品または電線の終端処理を行わないでください。

• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に従い、有資格の専門業者が行うようにしてください。

• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回しを行い、電気障害やつまづきの危険性など、安全上のリスクを回避するようにしてくだ

さい。

マニュアル、動画、FAQ、ドライバ、ダウンロード情報などを、www.StarTech.com/jp/Supportにてご覧いただけます。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

• Prodotto laser di Classe 1. Quando il sistema è aperto sono presenti radiazioni laser.

• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le linee elettriche sotto tensione.

• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un tecnico professionale certicato che conosca le linee guida locali sulle norme edilizie e

sulla sicurezza.

• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o pericoli per la

sicurezza.

Per visualizzare manuali, video, domande frequenti, download e altro ancora, visita

www.StarTech.com/it/assistenza-e-vendite.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

• Om laserproduktet är Klasse 1, laserstrålning avges när systemet är öppet.

• Montering av kabelavslutningar får inte göras när produkten och/eller elledningarna är strömförda.

• Installation och/eller montering får endast göras av behöriga yrkespersoner och enligt gällande lokala förordningar för säkerhet och byggnormer.

• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.

För nedladdningar, handböcker, videor och vanliga frågor, drivrutiner, besök www.StarTech.com/se/support.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of

this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.

startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.

com/downloads

Warranty Information

This product is backed by a one-year warranty. StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial

date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor

costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect,

special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed

the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or

exclusions contained in this statement may not apply to you.

FR: Guide de l’utilisateur - fr.startech.com

DE: Bedienungsanleitung - de.startech.com

ES: Guía del usuario - es.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

IT: Guida per l’uso - it.startech.com

JP: jp.startech.com取扱説明書-

3. Connect a CAT5 cable to the HDBaseT Output Port on the

HDBaseT Transmitter and to the HDBaseT Input Port on the

HDBaseT Receiver.

Note: Properly grounding the HDBaseT Transmitter and HDBaseT

Receiver can prevent damage and improve audio/video signal

quality.

4. Connect the Universal Power Adapter to the DC 12V Power Port

on either the HBaseT Transmitter or HDBaseT Receiver and to an

AC power outlet to power both the HDBaseT Transmitter and

HDBaseT Receiver (using the Power Over Cable feature).

Notes: Only use the type of HDBaseT Receiver included with this

kit. Mixing hardware with a dierent HDBaseT kit can damage your

equipment, due to the Power Over Cable feature.

Do not route the cable through any networking equipment.

Connecting Two Displays

1. On the back of the HDBaseT Transmitter, connect an HDMI cable

to the HDMI Output Port and to the HDMI port on a Local Display

(cables sold separately).

2. On the back of the HDBaseT Receiver, connect an HDMI cable to

the HDMI Output Port and to the HDMI port on a Local Display

(cables sold separately).

3. Power on each of your connected devices. The image from your

Video Source will now appear on your Remote Display.

EDID Settings

Adjust the EDID settings, if you’re experiencing poor resolution or

inconsistent audio/video output.

• On the back of the HDBaseT Transmitter, conrm that the Auto/

Inventory EDID switch is set to position 1.

Copying EDID Settings

1. On the back of the HDBaseT Transmitter, set the Auto/Inventory

EDID switch to either option 3 (copy video EDID and emulate

audio EDID) or 4 (copies video EDID and audio EDID).

Remote Display:

• To copy EDID settings from a Remote Display, press and hold

the EDID Copy Button for 3 seconds until the Remote LED

ashes green.

Local Display:

• To copy EDID settings from a Local Display, press and hold the

EDID Copy Button for 6 seconds until the Local LED ashes

green.

Switching Between Video Sources

1. On the back of the HDBaseT Transmitter, move the Mode Switch

Button to position 1.

2. On the front of either the HDBaseT Transmitter or the HDBaseT

Receiver, press the Input Selection Button that corresponds with

your desired video source.

3. The selected port’s LED will light up and the selected video

source will appear on the HDMI and HDBaseT displays.

Remote Control

1. On the right side of the IR Remote Control, press buttons 1 - 4 to

switch between HDMI 1, HDMI 2, DisplayPort, and VGA ports.

2. The selected port’s LED will light up, indicating the active port.

Resolution

The maximum resolution capability of the Extender Switch is Full HD

(1920 x 1080) up to 70 m (328 ft.).

Adjusting Resolution from the HDBaseT Receiver

1. On the HDBaseT Receiver, press the Menu Button to access the

OSD (On Screen Display) Main Menu.

2. On the OSD Main Menu, use the Navigation Buttons to select

Output Resolution and press the Enter Button.

3. On the Output Resolution sub-menu use the Navigation Buttons

to navigate/select a resolution and press the Enter Button to save

your changes.

The following options may also appear when changing your

resolution settings.

Revert

• Reverts back to the last resolution setting prior to saving.

Keep

• Saves the new resolution settings.

Product specificaties

Merk:	StarTech.com
Categorie:	AV extender
Model:	ST121HDBTSC
Kleur van het product:	Zwart
Gewicht:	2000 g
Breedte:	61 mm
Diepte:	106 mm
Hoogte:	67 mm
Type stekker:	Type M
Breedte verpakking:	98 mm
Diepte verpakking:	160 mm
Hoogte verpakking:	40 mm
Soort:	AV-zender & ontvanger
LED-indicatoren:	Ja
Stroom:	0.6 A
Connectiviteitstechnologie:	Bedraad
Maximum resolutie:	1920 x 1200 Pixels
Meegeleverde kabels:	LAN (RJ-45), Phone (RJ-11)
Snelstartgids:	Ja
Inclusief AC-adapter:	Ja
VGA (D-Sub)poort(en):	1
Certificering:	CE, FCC, TAA
Maximale refresh snelheid:	60 Hz
Aansluiting voor netstroomadapter:	Ja
Materiaal:	Aluminium
Ondersteunde grafische resoluties:	640 x 480 (VGA),800 x 600 (SVGA),1024 x 768 (XGA),1280 x 1024 (SXGA),1280 x 720 (HD 720),1280 x 800,1360 x 768 (WXGA),1366 х 768,1400 x 1050 (SXGA+),1440 x 900,1600 x 1200 (UXGA),1680 x 1050 (WSXGA+),1920 x 1080 (HD 1080),1920 x 1200 (WUXGA)
Remote (IR) ingang:	2
Duurzaamheidscertificaten:	RoHS
VGA (D-Sub) invoer ports:	1
RJ-11 ports kwantiteit:	2
DisplayPorts in:	1
Temperatuur bij opslag:	-10 - 60 °C
Externe adapter:	Ja
Rack-montage:	Ja
Audio-uitgangskanalen:	2.0 kanalen
Output current:	1.5 A
Remote (IR) uitgang:	2
AUX ingang:	Ja
HDMI in:	2
RJ-45 uitgang ports:	1
Montagebeugels meegeleverd:	Ja
Aantal HDMI-uitgangen:	2
RJ-45 invoer ports:	1
Rubberen voetjes:	Ja
Operating voltage:	12 V
Afstandsbediening inbegrepen:	Ja
(Buitenste) hoofdverpakking hoogte:	270 mm
(Buitenste) hoofdverpakking breedte:	385 mm
(Buitenste) hoofdverpakking lengte:	495 mm
Hoeveelheid per (buitenste) hoofdverpakking:	6 stuk(s)
Maximaal bereik:	70 m
AC-ingangsspanning:	100 - 240 V
Stroomverbruik (typisch):	18 W
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 80 procent
HDCP- & EDID-omzeiling:	Ja
Ondersteundende kabel types:	Cat5e, Cat6
3,5 mm in:	Ja
Inbegrepen soorten voedingsstekkers:	ANZ, EU, JP, NA, UK
Inclusief IR-versterker:	Ja
Inclusief IR-ontvanger:	Ja
Doorgelust:	Nee