SSV Works RG4-F65 Handleiding

SSV Works Speaker RG4-F65

Lees hieronder de πŸ“– handleiding in het Nederlandse voor SSV Works RG4-F65 (7 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7
RG4-F65
Polaris Ranger
6.5” Speaker Front Kick Panels
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in material
or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against
defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year
warranty against defects in material or workmanship. Labor for replacement of defective
components is not covered. Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
2. Enclosure Brackets x 41. RG4-F65 Enclosures
(1 pair)
3. M6 x 16mm Screws
x 10
- T-30 Torx Driver - Panel Removal Tool
4. M6 Washers x 8 (small) 4. M6 Washers x 2 (large)
A. Remove hood by turning locking pins and lifting up.
A
B. Use a panel tool to extract push pins circled in pink.
B
C. With push pins extracted, lift to remove the cup holder and gauge cluster.
C
- Phillips Screwdriver
K. Using the supplied M6 screws and small washers, install the
brackets to kick pods.
L. Remove factory T40 torx screws located from the front of the
dash next to the cup holders.
K L
F. Extract push pins that are now exposed from removing the
upper glove box.
H. Extract push pins exposed from gauge cluster removal.
I. Extract push pins located above driver and passenger side cup
holders.
F
H
I
E. Unscrew (4) torx screws located in upper glove box and
remove box.
G. Extract push pins exposed from cup holder removal.
E
G
J. Lift to remove the dash.
J
Connecting the RG4-F65 using the
pre-installed, two-pin connector will
require an optional SSV Works plug-
&-play harness (WP-H1149 - sold
separately). If you are not using the
WP-H1149 harness, simply cut off
the two-pin connector and follow the
wiring instruction.
Repeat for the other side.
RG4-F65 Β© 2018 SSV Works, Oxnard, CA 93030 RG4-F65 Rev. B 7-23-18
WIRING INSTRUCTIONS
For proper sound, ensure the speaker
polarity is correct connect the β€œ+” to
the β€œ+” and the β€œ-β€œto the β€œ-β€œfrom the
speaker wire to the amplier. If using
with an SSV Works complete system
refer to the amplier wiring instructions
for more detailed wiring information.
β€œ+”
β€œ+”
β€œ
-
”
β€œ
-
”
M. Remove factory T25 torx screws located underneath the dash. N. Located on the inside top of the pocket you will have two
holes, route speaker wire though the larger hole. The smaller
hole will be used to mount the pod in Step P.
O. Place the speaker pod in location and resecure the factory screws through the pod brackets on the front and underneath the dash.
P. From the inside-top of the dash, secure the top mounting M6 screw and large washer to the pod through the smaller hole next to
the routed speaker wire.
M N
O
P P
O


Product specificaties

Merk: SSV Works
Categorie: Speaker
Model: RG4-F65

Heb je hulp nodig?

Als je hulp nodig hebt met SSV Works RG4-F65 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker SSV Works

Handleiding Speaker

Nieuwste handleidingen voor Speaker