Speco Technologies HiD8 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Speco Technologies HiD8 (2 pagina's) in de categorie Videocamera. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
HD-TVI 2MP Ultra Intensier® Vandal Dome Camera
QUICK INSTALLATION GUIDE
Special features
Sony 1/2.8" 2.1MP STARVIS CMOS Sensor
Supports image resolution up to 1920 10 P @ 30fps x 80
Max. Transmission distance: 985ft over Coaxial cable
Ultra low light performance
F = 0.95, 3.6mm 2Megapixel Fixed Lens
TVI / CVBS (EXT) Output
Supports WDR, Defog, 2D / 3D DNR, Slow Shutter control (Sense-Up)
Privacy Masking up to 16 areas
Full OSD operation through on board control and UTC (up the coax)
Dynamic Motion Detection (4separable areas)
Supports 5 Languages
Perfect 3-Axis Mechanism
12VDC operation
IP67 compliant
DEAR CUSTOMERS!
By selecting this product, you have decided to use a professional device that
guarantees highest quality and reliability. We would like to thank you very much for
your condence and kindly ask you to read the following instructions carefully before
installation and operation in order to take full advantage of all quality features
regarding this product.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
WARNING
Changes or modications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
CAUTION –To prevent electric shock and risk of the re hazards
Do NOT use power source other than that specied.
Do NOT expose this appliance to rain or moisture.
1. Precautions
Please read the manual carefully before the installation in order to make use the
camera to be set up correctly and to have the best picture quality.
Please keep the manual in good condition for your future reference and service
application.
Installation and services should only be carried out by an authorized personnel
according to local safety regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera
from power supply and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places.
If you are not a certied person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside
that need maintenance by the user. All maintenance should be carried out by qualied
personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Keep the top glass of the lens always clean in order to obtain the best picture quality
all the time. Be careful not to be stained by ngerprint.
Don't face the camera directly toward sunlight or sunlight reecting area.
CMOS may go defective at this condition.
Please give a special attention to keep the unit from dangerous drop or external shock
during the process of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the CMOS.
2. Limitation of liability
This publication is provided “AS IS” without warranty of any kind, either express or
implied, including but not limited to, the implied warranties of merchantability, tness for
any particular purpose, or non-infringement of the third party's right.
This publication could include technical inaccuracies or typographical errors.
Changes are added to the information herein, at any time, for the improvements of this
publication and / or the corresponding product(s).
3. Disclaimer of warranty
In no event shall seller be liable to any party or any person, except for replacement or
reasonable maintenance of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of
the user.
(3) Unauthorized disassemble, repair or modication of the product by the user.
(4) Inconvenience or any loss arising when images are not displayed, due to any reason
or cause including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the
system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being
photogenic subject, due to violation of privacy with the result of that surveillance-
camera's picture, including saved data, for some reason, becomes public or is used
for the purpose other than surveillance.
4. Package
- Junction Box
5. Installation
5-1 Adjust Pan, tilt and Rotation and the View Angle .
Pan, Tilt, Rotate (3-Axis mechanism) makes easy to monitor the desired view
。
。
。
。。
Panning axis can be adjusted 360°
Tilting axis can be adjusted 0° ~ 90°
Rotating axis can be adjusted
between +180° (clockwise)
and -180° (counter-clockwise)
Do not rotate more 180° as this
might cause the internal cables to
twist and disconnect or break.
- How to adjust the View Angle
a. Panning 360 degree
Turn the pan base right or left to adjust the pan angle.
b. Tilting 90 degree
Loosen the tilt lever on the right or left side of the camera board.
Control the camera tilt angle and fasten the tilt lever again.
c. Rotation 180 degree
Grasp the front side of the camera board and turn it right or left to set the exact
angle of image.
5-2. How to install on the Ceiling
① Paste a Drilling Template on the ceiling. (or wall)
② Drill screw points which will be done for installation.
Fix the plastic anchors in the holes. (in case of masonry ceiling or wall)
③ Mount the camera set by using Tapping Screws with Ø 4 provided.
④ Set the position and angle of the cameras to a desired direction and assemble the dome
cover.
The lighting ash with an arrowhead symbol, within an equilateral triangle
is intended to alert the user to the presence of non-insulated dangerous
voltage within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
This installation should be made by a qualied service person and should conform to
all local codes.
CAUTION
TO REDUCE THE RISK OF ELECTRLC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRLC
SHOCK
DO NOT OPEN
CAUTION
HiD8
Camera x 1
Manual x 1
Extra Video
output x 1
Tapping screws x 3
Plastic anchor x 3
Drilling template x 1
Torx Wrench x 1
BNC Female for TVI
Ceiling Tile
Drilling template
Plastic Anchor (3EA)
Tapping Screw
Ø 4 x 1.18in (3EA)
Dome Cover
Ass'y
Torx Screw
Ø 3 x 0.59 (3EA)
Torx L-Wrench
Safety Wire
Camera Ass'y
DC Power Jack
The front side of the
camera
Tilt lever
Tilt 90˚
Rotate
180˚
Pan 360˚
Pan base
Top Rubber x 1
Junction Box x 1
Sponge x1
Screw PH
(M4 x 0.47in) x 3
Tapping Screws
(Ø 4 x 1.18in) x 4
Plastic Anchor x 4
Chameleon
Cover x 1
5. Installation
Ceiling_Junction Box
① Attach the Sponge on junction Box.
② Mark the hole of junction box on the ceiling with tapping screw.
③ Drill the hole and input the anchor. And install the junction box with Tapping Screw.
④ Input Cable inside Junction Box.
⑤ Install Bottom Ass'y on junction box with PH M4 x 0.47in.
⑥ Install Top Case Ass'y on Bottom Ass'y with L-Wrench.
5-3 Application of TVI output .
6. Function and operation
6-1. On Screen Display (On board control and UTC)
PRESET MENU
INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY / ELEVATOR
SETUP
LENS
DC
MANUAL
EXPOSURE
BRIGHTNESS
SHUTTER
INTENSIFY
AGC
RETURN
WHITE BAL
AUTO
AWB
AWC-SET
MANUAL
BACKLIGHT
WDR
BLC
HLC
OFF
DAY&NIGHT
COLOR
B/W
AUTO
DNR
LOW
MIDDLE
HIGH
RETURN
IMAGE
SHARPNESS
ACE
GAMMA
DEFOG
COLOR
GAIN
RETURN
MIRROR
FLIP
MOTION
ON
OFF
SYSTEM
ANALOG HD
COLOR BAR
RESET
FRAME RATE
LANGUAGE
FREQ
CAM TITLE
IMAGE RANGE
CAM TITLE
COLOR SPACE
RETURN
EXIT
7. Troubleshooting
If there are problems in operating, please refer to the checklist below.
If the problem persists, please contact the agent where this product is purchased.
Problems
Troubleshooting
Nothing appears on
the screen.
Please check that the power cord and line connection
between the camera and monitor are xed properly.
Please check that you have properly connected Video cable to
the camera Video output jack.
The dim image
on the screen.
Is lens stained with dirt? Clean your lens with soft, clean cloth.
Set the monitor to proper condition.
If the camera is exposed to too strong light, change the
camera position.
Please check if the power supply is within the specication &
cables.(Due to the voltage drop with distance and gauges,
L will light poor) ed
The dark image
on the screen.
Adjust the contrast feature of the monitor.
If there is an intermediate device, set the 75Ω / Hi-Z properly.
(Please check the impedance)
The camera is not
working properly,
and the body of the
camera is hot.
Please check if the power supply is regulated and is within the
standard requirement of the products.
Color is not correct.
Please check the setting of White Balance setup.
The screen is
ickering.
Please check if the camera is facing directly towards sunlight
or uorescent light.
8 Dimension ( ) . in
9. Specications
MODEL
HiD8
Image sensor
Sony 1/2.8 inch 2.1MP STARVIS CMOS Sensor
Total Pixel
1945(H) x 1109(V) 2.16 Megapixel
Eective Pixels
1945(H) x 1097(V) 2.13 Megapixel
Scanning system
Progressive scan
Video output
1920 x 1080 @ 25fps / 30fps, 1280 x 720 @ 25fps /
30fps
Output
TVI
S/N ratio
More than 520B (AGC OFF / Weight ON)
Min. Illumination
0.001Lux
Privacy Mask
ON / OFF (16 zone)
Motion
ON / OFF (4 zone)
NEG.Image
ON / OFF
Mirror / Flip
ON / OFF
White Balance
AUTO / AWB / AWB - SET / MANUAL
Shutter
AUTO / MANUAL / FLICKER
Sens- UP
AUTO / OFF (Selectable Limit p2-x2 ~ x32)
Backlight
OFF / HLC / BLC / WDR
2D / 3DNR
OFF / LOW / MIDDLE / HIGH
AGC (Auto Gain Control)
0 ~ 10 (Level adjustable)
Day & Night
COLOR / B&W / AUTO
Sharpness
0 ~ 10 (Level adjustable)
WDR
NORMAL / ROI
Defog
ON / OFF
Language
ENG, CHN, CHN(S), JPN, KOR
Lens
F=0.95, 3.6mm 2Megaxel Fixed Lens
Power Source
12VDC
Operating current
100mA ±10% (12VDC)
Operating
Temperature
-40F ~ 140F
Storage
Temperature
-40F ~ 140F
Operating Humidity
0%RH ~ 90%RH
Measurement( ) in
121.2(Ø ) x 3.79(H)
Weight(Approx. ) oz
52oz
Speci cations are subject to change without prior notice for better improvement. fi
Coaxial
5C / 3C
TVI DVR
Monitor
Ceiling Tile
Plastic Anchor (4 EA)
Junction Base Sponge
Junction B Assemblyox
Tapping Screw Ø 4 1.18in (4 x EA)
Bottom Ass'y
Safety Wire
PH M4 0.47in (3x EA)
T Case Ass'yop
L-Wrench
190515_SPECO_TVI
Federal Communications Commission (FCC) Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
FCC Responsible Party :
Speco Technologies
200 New Highway
Amityville, NY 11701
www.specotech.com
Product specificaties
Merk: | Speco Technologies |
Categorie: | Videocamera |
Model: | HiD8 |
Heb je hulp nodig?
Als je hulp nodig hebt met Speco Technologies HiD8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Videocamera Speco Technologies
16 Juni 2023
15 Juni 2023
14 Juni 2023
14 Juni 2023
13 Juni 2023
12 Juni 2023
9 Juni 2023
9 Juni 2023
8 Juni 2023
6 Juni 2023
Handleiding Videocamera
- Videocamera Philips
- Videocamera Sony
- Videocamera Samsung
- Videocamera Panasonic
- Videocamera Canon
- Videocamera JVC
- Videocamera Toshiba
- Videocamera BlackVue
- Videocamera Bluetech
- Videocamera Brinno
- Videocamera Bushnell
- Videocamera Denver
- Videocamera Extech
- Videocamera Flip
- Videocamera Flir
- Videocamera Izzo
- Videocamera Kogan
- Videocamera Laserliner
- Videocamera Maginon
- Videocamera MD 80
- Videocamera Milwaukee
- Videocamera Nedis
- Videocamera PCE Instruments
- Videocamera Praktica
- Videocamera Ricatech
- Videocamera Spypoint
- Videocamera Thinkware
- Videocamera Tronje
- Videocamera Trotec
- Videocamera Vitek
- Videocamera Voltcraft
- Videocamera Zoom
- Videocamera Creative
- Videocamera Klein Tools
- Videocamera Akaso
- Videocamera Xblitz
- Videocamera Hazet
- Videocamera DataVideo
- Videocamera Kreator
- Videocamera Vimar
- Videocamera Berger & Schröter
- Videocamera Revier Manager
- Videocamera Rexing
- Videocamera Moultrie
- Videocamera Teslong
Nieuwste handleidingen voor Videocamera
1 December 2024
30 November 2024
30 November 2024
30 November 2024
30 November 2024
30 November 2024
30 November 2024
30 November 2024
25 November 2024
24 November 2024