SoundTube DS31-EZ Handleiding

SoundTube Speaker DS31-EZ

Lees hieronder de 📖 handleiding in het Nederlandse voor SoundTube DS31-EZ (3 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Install Instructions For:

DS31-EZ

Box contents

1.435.647.9555

800.647.TUBE

www.soundtube.com

Do not spec or install speaker near support beam, ventilation duct or

other structure that may interfere with speaker function or dispersion.

Warning Warning

SoundTube speakers must be installed by ofessional audio installer/contracto For safety and for a pr r.

optimum audio performance, installer must follow all di ections issued by Sound r Tube Entertainment .

(1) Speaker assembly

(1) Cylindrical or Tapered sleeve

(1) Magnetic grille

(1) Mounting Assembly

(2) Mounting screws

(2) 2.25” sleeve screws

(2) 0.50” screws

(2) Wire nuts

Cover plate

Tapered Sleeve

Mounting plate

Mounting screws (2)

Dual-Gang Junction Box (not included)

Speaker

Grille

Safety Clip

Safety leash

Adjustment loop

Tapered Sleeve

Tap Settings

Cylindrical Sleeve

(two pieces)

Install Instructions For:

DS31-EZ

1. Remove speaker body from

box and unravel signal wire.

2. 3. Unpack Designer Sleeve. Select tap setting on the

back face of the speaker body.

Each numeral setting

corresponds to a wattage

shown in tap setting table on

back of speaker (also shown

on Page 1). Use 8Ω for

transformer bypass.

4. If necessary, attach safety

cable by rst inserting into side

of mounting bracket.

8. Thread signal wire through

Designer Sleeve central hole,

then gently slide sleeve down

OVER safety clip wire and

speaker body. Then use two

included 2.25” Phillips-head

screws to secure sleeve to

speaker body (Tapered Sleeve

shown).

9. If using both Cylindrical

Sleeve pieces, use two

included 0.50” Phillips-head

screws to secure the two

sleeve pieces to one another.

10. Thread signal wire through

included Strain Relief Bushing.

11. Screw bushing into

Designer Sleeve, pulling excess

wire through until snug.

12. Tighten down top gland to

secure the signal wire. Gland

must be tightened around

signal cable to prevent water

ingress and maintain IP rating.

1.855.663.5600

www.soundtube.com

5. Align safety cable with

bracket slot and pull up to

secure.

6. Unpack grille and attach

grille safety restraint by placing

the large end of the clip over

the mounting bracket screw on

the top face of the speaker

body (the face opposite the

front of the speaker).

7. You will need to slightly

loosen/unscrew one of the

hanging bracket screws in

order to t the safety clip

underneath. Slide the safety

clip until the small end snaps

into place around the screw.

Install Instructions For:

DS31-EZ

1.855.663.5600

www.soundtube.com

13. Unpack Mounting Assembly

and separate hemispherical

cover plate from mounting plate.

Thread signal wire through

hemispherical cover plate and

central hole in mounting plate.

17. Move cover plate up

speaker wire, begin to thread

cover plate into mounting plate,

leaving half an inch between

cover plate and mounting

surface.

18. Excess wire can be

hidden inside of cover plate by

wrapping excess wire clock-

wise and into gap between

plate and surface.

20. Magnetically attach grille

to the front of the speaker.

Done.

19. Completely thread cover

plate to secure speaker.

14. Where needed, connect

safety leash to secure point on

structure/ junction box.

15. Loop wire down through

one of the smaller holes on the

mounting plate, then back up

through adjacent hole. Run

signal wire from amplier to the

speaker and connect it to the

speaker’s signal wire using

included wire nuts. Red is

positive, black is negative.

16. Screw mounting plate into

the junction box (not included)

using the mounting screws

provided.

Product specificaties

Merk:	SoundTube
Categorie:	Speaker
Model:	DS31-EZ
Kleur van het product:	Zilver
Gewicht:	2720 g
Hoogte:	215.9 mm
Materiaal behuizing:	Acrylonitrielbutadieenstyreen (ABS)
Internationale veiligheidscode (IP):	IPX6
Type verpakking:	Doos
Connectiviteitstechnologie:	Bedraad
Diameter:	139.7 mm
Gemiddeld vermogen:	30 W
Certificering:	CE, RoHS
Aantal per verpakking:	1 stuk(s)
Aanbevolen gebruik:	Thuis
Impedantie:	8 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Plafond-montage
Aantal drivers:	1
Diameter driver:	76.2 mm
Frequentiebereik:	80 - 20000 Hz
Gevoeligheid:	87 dB
Driver cone material:	Polypropyleen
Roostermateriaal van luidspreker:	Staal