SoundTube CM31-EZ Handleiding

SoundTube Speaker CM31-EZ

Lees hieronder de 📖 handleiding in het Nederlandse voor SoundTube CM31-EZ (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

CM31-EZ

Do not spec or install speaker near support beam, ventilation duct or

other structure that may interfere with speaker function or dispersion.

Warning

SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for

optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.

Grille

Installation aid/paint mask

Baffle

SpeedWing™ mounting arms

Speaker seismic restraint hole

Tile bridge

Flexible conduit clamp

Signal wires

Grille safety clip

1. Nail or screw bracket to

joists.

2. Finish installing ceiling.

8. Remove paint mask

unless painting is required.

In that case, follow steps

9-12 when painting is

complete.

9. Adjust tap switch to

proper setting. Switch is

preset to the highest setting

in the 70.7-volt mode.

10. Attach grille safety clip

by placing the large end of

the clip over snap-fit post (1),

then sliding clip until small

end snaps into place around

post (2).

5. Feed speaker wires

through conduit clamp and

connect with wire nuts.

Push wire nuts into backcan

and affix conduit clamp.

3. Use RotoZip or other tool

to cut hole.

7. Insert speaker into

mounting hole. Tighten both

bolts on the baffle face to

actuate the mounting wings.

DO NOT OVERTIGHTEN.

6. If required, attach

seismic restraint system to

the sheet-metal tab on the

rear panel of the speaker,

then to reinforced structure

(safety cable not included).

11. Align tabs on snap-fit

grille with slots in baffle,

gently press grille into place.

1. Unpack speaker. Leave

paint mask in place until

after speaker is installed or

painting is complete.

4. Unpack speaker. Leave

paint mask in place until

after speaker is installed or

painting is complete.

2. Use included tile bridge

to mark cutout on

sheetrock. Tile bridge ships

in separate box.

3. Use RotoZip or other tool

to cut hole. Hole diameter:

5.6 in. (142 mm).

4. Feed speaker wires

through conduit clamp and

connect with wire nuts.

Push wire nuts into backcan

and affix conduit clamp.

8. Adjust tap switch to

proper setting. Switch is

preset to the highest

setting in the 70.7-volt

mode.

5. If required, attach seismic

restraint system to hole in

clamping arm, then to

reinforced structure (safety

cable not included).

2. Use included tile bridge

to mark cutout on tile.

1. Unpack speaker. Leave

paint mask in place until

after speaker is installed or

painting is complete. Tile

bridge ships in separate box.

3. Use RotoZip or other tool

to cut hole. Hole diameter:

5.6 in. (142 mm).

4. Insert speaker into

mounting hole on ground

with tile bridge and paint

mask in place. Tighten both

screws on the baffle face to

actuate the mounting wings.

Firmly secure both screws,

DO NOT OVERTIGHTEN.

Put assembly into tile grid.

5. Feed speaker wires

through conduit clamp and

connect with wire nuts.

Push wire nuts into backcan

and affix conduit clamp.

6. If required, attach seismic

restraint system to hole in

clamping arm, then to

reinforced structure (safety

cable not included).

8. Adjust tap switch to

proper setting. Switch is

preset to the highest setting

in the 70.7-volt mode.

9. Attach grille safety clip by

placing the large end of the

clip over snap-fit post (1),

then sliding clip until small

end snaps into place around

post (2).

10. Align tabs on snap-fit

grille with slots in baffle,

gently press grille into place.

11. Done! 11. Done! 12. Done!9. Attach grille safety clip by

placing the large end of the

clip over snap-fit post (1),

then sliding clip until small

end snaps into place around

post (2).

10. Align tabs on snap-fit

grille with slots in baffle,

gently press grille into place.

7. Remove paint mask

unless painting is required.

In that case, follow steps

8-11 when painting is

complete.

7. Remove paint mask

unless painting is required.

In that case, follow steps

8-11 when painting is

complete.

6. Insert speaker into

mounting hole with paint

mask in place. Tighten both

bolts on the baffle face to

actuate the mounting wings.

Firmly secure both bolts,

DO NOT OVERTIGHTEN.

Box contents

1 Speaker

1 Grille

1 Paint mask

2 Wire nuts

1 UL-listed conduit clamp

Note: Tile bridge included, ships in separate box.

Install Instructions For:

CM31-EZ speaker

1.435.647.9555

| | 800.647.TUBE

www.soundtube.com

CM31-EZ Pre-Construction Bracket Instructions For:

CM31-EZ speaker (Pre-construction bracket sold separately)

1.435.647.9555

| | 800.647.TUBE

www.soundtube.com

CM31-EZ Sheetrock Installation Instructions For:

CM31-EZ speaker

1.435.647.9555

| | 800.647.TUBE

www.soundtube.com

CM31-EZ Drop-tile Installation Instructions For:

CM31-EZ speaker

1.435.647.9555

| | 800.647.TUBE

www.soundtube.com

CM31-EZ

Product specificaties

Merk:	SoundTube
Categorie:	Speaker
Model:	CM31-EZ
Kleur van het product:	Aluminium, White
Gewicht:	1400 g
Gewicht verpakking:	1680 g
Breedte verpakking:	184.15 mm
Diepte verpakking:	203.2 mm
Hoogte verpakking:	209.55 mm
Gebruikershandleiding:	Ja
Materiaal behuizing:	Acrylonitrile butadiene styrene (ABS), Aluminium
Internationale veiligheidscode (IP):	IP54
Bluetooth:	Nee
Type verpakking:	Doos
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	20 W
Certificering:	CE, RoHS, UL1480A, UL2043
Duurzaamheidscertificaten:	CE, RoHS
Aantal per verpakking:	1 stuk(s)
Aanbevolen gebruik:	Universeel
Impedantie:	8 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Frequentiebereik:	115 - 22000 Hz
Gevoeligheid:	85 dB
Versterker:	Nee
Diameter hogetonenluidspreker:	3 "
Tweeter:	Ja