Soundmaster DISC4020 Handleiding

Soundmaster Hifi systeem DISC4020

Lees hieronder de 📖 handleiding in het Nederlandse voor Soundmaster DISC4020 (7 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

DISC4020 / English Manual

ENG 1

LOCATION OF CONTROLS

MAIN UNIT

1) LCD display

2) Remote sensor

3) Standby LED indicator

4) CD door

5) USB Socket

6) SD/MMC card slot

7) Snooze button

8) Alarm button

9) Stop /St-Mono button

10) Play/Pause button

11) Volume knob

12) On/Standby button

13) Function button

14) Preset EQ button

15) Folder/Pre-Up button

16) Skip/Tuning Up /Down button

17) Memory/Clock-Adjust button

18) Play Mode button

19) FM wire antenna

20) Aux-in jack

21) 3.5mm Headphone jack

22) DC jack

23) AC/DC adaptor

24) DC plug

Caution:

Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous

radiation exposure.

This unit should not be adjusted or repaired by anyone except qualified service personnel.

Important:

Since movement of the CD mechanism and the sensitive circuitry may cause interference to the radio tuner nearby, switch this

unit off while operating other radio devices

Precautions for use

Installation

• Unpack all parts and remove protective material.

• Do not connect the unit to the mains before checking the main voltage and before all other connections have been made.

• Do not cover any vents and make sure that there is a sp ound the unit for ventilation. ace of several centimeters ar

Connection

1. Connect the DC plug (24) to the DC jack (22) of the main unit, then plug in the AC/DC adaptor (23) to the AC outlet. The unit

will go to standby mode and the Standby LED indicator (3) will light up.

2. Turn on the unit (12), if the LCD display (1) is on with backlighting, it means the power supply is normal. Now your system is

ready to play the music.

DISC4020 / English Manual

ENG 2

Setting the clock

1. Set unit in standby mode.

2. Press & hold the “ Mem/Clk-Adj ” button (17), display will flash “24HR” press the Skip Up or Skip Down button

(16) to select the clock format between 12 or 24Hour. Then press the “ Mem/Clk-Adj ” button (17).

3. The first digit of “ 0:00 ” is flashing on the LCD display (1). Press Skip Up or Skip Down button (16) to set the

correct hour. Press “ Mem/Clk-Adj ” button (17) to store the correct hour.

4. The third & fourth digit of “ 00 ” is flashing, press the Skip Up or Skip Down button (16) to set the correct minutes.

Then press “ Mem/Clk-Adj ” button (17) to store the correct minute.

¾ The clock setting mode will automatically quit if no button is being pressed in a period of about 5 seconds after

pressing the “ Mem/Clk-Adj ” button.

¾ The pre-set time will be re-set completely if dis-connecting the main power supply. You are

recommended to switch the system into standby mode for convenience usage.

Listening to radio

Manual tuning

1. Switch on the unit by On/Standby button (12), then press Function button (13) to select “ Tuner ” mode.

2. Tune to the required station by pressing the Tuning Up or Down button (16).

3. Press the Volume knob (11) to the desired volume level.

Auto tuning

1. Press Function button (13) to select “ Tuner ” mode.

2. Press and hold the Tuning Up or Down button (16) for 1-2 seconds and then release.

3. The unit will start seeking automatically and stop until a radio station is reached.

4. Repeat step 2 & 3 until the desired radio station is being reached.

5. Press Volume knob (11) to the desired volume level.

Preset stations

You can store up to 10 radio stations in the memory

Set to tuner mode.

1. Turn to the desired radio station by “ Manual” or “ Auto ” tuning method.

2. Press and hold the Mem/Clk-Adj ” button (17) until the “ MEM ” indicator and preset station number are flash on LCD display

(1)

3. Press “ Folder / Pre-up button (15) to select the desired station memory for storage.

4. Press “ Mem/Clk-Adj ” button (17) again to confirm the setting.

5. Repeat step 1 to 4 to store other stations.

6. Now you can select the presets stations in order by pressing the “Folder/Pre–up ” button (17)

¾ The pre-set memories will be cancelled completely if dis-connecting the main power supply. You are recommended to

switch the system into standby mode for convenience usage.

¾ There are 5 seconds for program state, after 5 sec. This state would resume to normal tuner mode automatically.

¾ You can overwrite a present station by storing another frequency in its place.

FM-Stereo reception

z Press the “ St/Mono ” button (9) repeatedly, the FM programs are receiving in mono and stereo mode repeatedly. In

particular when stereo signals are weak, it is preferable to receive the program in Mono.

z If stereo signal is being received, the stereo indicator “ ” will appear on LCD display (1) to show FM Stereo program

is now receiving.

Hints for best reception:-

- FM : the receiver has a build-in FM wire antenna (19) hanging at the rear cabinet, this wire should be totally unraveled and

extended for the best reception.

DISC4020 / English Manual

ENG 3

Playing Compact Disc

z Getting start

1. Press Function button (13) to select “ CD ” mode.

2. Push the CD door open (4) to open the CD door.

3. Place a CD with the printed side facing out and then close the CD.

4. Focus search will performing and the LCD display (1) will show

the total number of tracks & total playing time. Then, the un

will start to automatically.

5. Press Volume knob (11) to the desired volume level.

z Play / Pause mode

1. To interrupt, press the “ Play/Pause ” button (10) once, and the playing time will be freeze on the LCD display (1). Press

again to resume normal playback.

z Stop mode

1. If “ Stop ” button (9) is pressed during play or pause mode, system will go to stop mode.

z Skip mode (skip up / skip down )

1. During play or pause mode, if “ skip up

” button (16) is pressed. It will go to next

track and display the track no. and then

remain the play or pause mode.

2. During play or pause mode, if “ skip down ” button (16) is pressed. It will go to the previous track, original track no. is

display and remain the play or pause mode.

z For MP3 Disc

1. After focus search is performing, the total number of track and album will be shown on the LCD display (1). The unit will start

to plat directly.

2. Press “ Folder/ Pre-Up (15) or Pre-Down ” at remote control to select the folder number.

3. Press “ Skip Up or Skip Down ” button (16) to select the track number.

ID3/Display function (On remote control)

Press the “ ID3 “ button on the remote control repeatedly, the LCD display (1) show “ file - … ”during playback of MP3/WMA file,

the song file/album/song/artist name/clock time is being displayed in sequence . Press the “ ID3 ” button until display show the

running time to disable the function.

Remark:-

- In that case of no name or not supportive languages had been assigned for the track, LCD display will blank (1) when press the

ID3 button.

- No Title/Album name can be recognized if the input format on the Disc is not supporting by the system.

- The system support only English and Arabic number for ID3 function.

Product specificaties

Merk:	Soundmaster
Categorie:	Hifi systeem
Model:	DISC4020
Kleur van het product:	Zwart
Breedte:	358 mm
Diepte:	87 mm
Hoogte:	202 mm
Geïntegreerde klok:	Ja
Stroombron:	AC
Video recording:	Nee
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	SD
Inclusief AC-adapter:	Ja
Gemiddeld vermogen:	40 W
Aantal luidsprekers:	2
MP3 afspelen:	Ja
ID3 Tag weergave:	Ja
Ophangsysteem voor aan de muur:	Ja
Karaoke:	Nee
Playback disc formaten:	Cd-audio
AUX ingang:	Ja
Optische drive type:	CD,CD-R,CD-RW
Ondersteunde frequentiebanden:	FM
Aantal voorkeurszenders:	20
Optical disc player:	Ja
Aantal optische schijven:	1 schijven
Cassette deck:	Nee
Luidspreker soort:	1-weg
Apple docking-compatibiliteit:	Niet ondersteund
Afstandsbediening inbegrepen:	Ja
Type beeldscherm:	LCD