Sonance Visual Performance VP85S SST Handleiding

Sonance Speaker Visual Performance VP85S SST

Lees hieronder de 📖 handleiding in het Nederlandse voor Sonance Visual Performance VP85S SST (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Introduction
Thank you for purchasing Sonance Visual Performance®
Series Large round or square speakers. When properly installed
your new speakers will give you years of entertainment pleasure.
Box Contents
Sonance Visual Performance Series in-ceiling speaker boxes
contain (2) Visual Performance Large round or square speakers,
(2) paint plugs (installed on the fronts of the speakers),
(2) paintable grilles and (1) mounting cut-out template.
Speaker Placement
Distributed Audio Placement (Mono signal)
All Sonance Visual Performance Series in-ceiling speaker models
provide excellent coverage in distributed audio systems from a
wide variety of installation locations.
The table and illustration in
Figure 1
show how far apart the
speakers can be placed at various ceiling heights while still
providing good coverage for all listeners.
Home Theater Speaker Placement
Left, Center & Right Speakers (see Figure 2)
Place the left, center and right speakers 1 2 feet (0.3m 0.6m)
in front of the video screen, 6 10 feet (1.8m 3m) apart,
with the center channel speaker as close to midway between
the left and right speakers as possible.
The main listening position should be 4 10 feet (1.2m 2m)
away from the speakers.
Surround Speakers 5.1-Channel System (see Figure 2)
Locate the left and right surround speakers 2 6 feet (0.6m
1.8m) behind the listening position. The speakers should be
6 10 feet (1.8m 3m) apart.
Surround Speakers 7.1-Channel System (see Figure 3)
Le ft & Ri ght Surround Spe akers:
Left & Right Surround Speakers:
Left & Right Surround Speakers:
Left & Right Surround Speakers:Left & Right Surround Speakers: Place the left and right
surround speakers directly to the sides of the listening position,
6 10 feet (1.8m 3m) apart.
Surround Back Speakers:
Surround Back Speakers:
Surround Back Speakers:
Surround Back Speakers:Surround Back Speakers: Place the surround back speakers
2 6 feet (0.6m 1.8m) behind the listening position. The
surround back speakers should be closer together than the left
and right surround speakers, 3 6 feet (0.9m 1.8m) apart.
I N S T A L L A T I O N M A N U A L
V I S U A L P E R F O R M A N C E ® S E R I E S
L A R G E R O U N D A N D
S Q U A R E S P E A K E R S
S W :AFETY ARNING
THESE SPEAKERS HAVE AST OUNTF M ®TABS THAT PREVENT THE
SPEAKER FROM FALLING OUT OF THE MOUNTING HOLE DURING T HE
INSTALLATION PROCESS.
T F MH E E D GE S O F T H E A S T OU N T T A B S A R E V ER Y S H A RP.
US E C A U T IO N W HE N H A N DL I NG T H E S P E A K ER .
TV
3' – 6'
(0.9m – 1.8m)
Apart
2' – 6'
(0.6m – 1.8m)
Less than 2’ (0.6m)
Surround
Back
Speakers
Left, Center
& Right
Speakers
Left & Right
Surround Speakers
6'– 10'
(1.8m – 3m)
Apart
1'– 2'
(0.3m – 0.6m)
F H T S PIGURE 3: 7.1-CHANNEL OME HEATER PEAKER LACEMENT
TV
6'– 10'
(1.8m – 3m)
Apart
6'– 10'
(1.8m – 3m)
Apart
1'– 2'
(0.3m – 0.6m)
Left, Center
& Right
Speakers
Less than 2’ (0.6m) 2' – 6'
(0.6m – 1.8m)
Left & Right
Surround
Speakers
F H T S PIGURE 2: 5.1-CHANNEL OME HEATER PEAKER LACEMENT
C
OVERAGE
A
REA
C
OVERAGE
A
REA
S
PEAKER
S
PACING
S
PEAKER
S
PACING
(
IN
FEET
)
FOR
A
D
ISTRIBUTED
A
UDIO
S
YSTEM
S
TANDING
L
ISTENER
S
EATED
L
ISTENER
10-
F
OOT
C
EILING
12-
F
OOT
C
EILING
14-
F
OOT
C
EILING
8-
F
OOT
C
EILING
9.5’ (2.9m) Apart
13.5’ (4.1m) Apart
17.5’ (5.3m) Apart
21.5’ (6.6m) Apart
5.7’ (1.7m) Apart
9.7’ (3.0m) Apart
13.7’ (4.2m) Apart
17.7’ (5.4m) Apart
F A S SIGURE 1: DISTRIBUTED UDIO PEAKER PACING
2
SONANCE VISUAL PERFORMANCE®LARGE ROUND AND SQUARE
Stereo Placement (2-Channel)
Place the left and right speakers anywhere from 6 feet to 10
feet apart, with the main listening position as close to midway
between the speakers as possible.
In most cases pivoting the woofer and/or midrange/tweeter
assembly of each speaker directly towards the main listening
position will help maximize the stereo soundstage.
Use the Left and Right speaker placement in
Figures 2
and
3
, on
page 1, as a guide.
Before Installation
1. Determine the location for the speaker (see
Speaker Placement
on page 1).
2. Perform an obstruction survey to be certain that there are no
studs, conduit, pipes, heating ducts, pocket doors or air returns
in the ceiling cavity that will interfere with the speaker.
3. Mounti ng space requirem en ts:
Mounting space requireme nts:
Mounting space requireme nts:
Mounting space requireme nts:Mounting space requireme nts:
Large round speakers: 101
/8 (257mm) diameter cut-out;
57/8 (149mm) mounting depth.
Large square speakers: 10¼ x 10¼ (260mm x 260mm)
cut-out; 5 7/8 (149mm) mounting depth.
4. Position the included cut-out template where the speaker is to
be located and pencil an outline on the ceiling. If you are
unsure about obstructions, drill a small hole in the center of
the outline and insert a coat hanger wire into the hole to feel-
around for possible obstructions.
5. Cut the mounting hole using a keyhole or drywall saw, and run
the speaker wires from the mounting hole to the amplifier
location.
NOTE : CON SU LT LOC AL B U IL DI NG C OD ES B E FOR E R U NN I NG
SP E AK E R W IR ES T HR OU G H C EI LI NG S.
Installation
Sonance Visual Performance Series speakers feature exclusive
FastMount tabs and an integral Roto-Lock®mounting system for
quick mounting directly into existing ceilings.
WARNING: THE EDGES OF THE FASTMOUNT TABS
ARE VERY SHARP. USE CAUTION WHEN HANDLING
THE SPEAKER.
1. Remove the paint plug from the speaker.
2. Strip ¼ ½ (6mm 12mm) of insulation from each speaker
lead. Twist the strands or tin the exposed wire with solder to
ensure that there are no stray strands. (Stray strands that touch
each other can cause a short-circuit that can damage the
amplifier.)
3. The speaker’s connector posts are spring-loaded. Push the top
of each connector post down to open the connector and insert
the exposed wires into the holes in the posts.
The speaker’s positive post is labeled with a red dot; the
negative post is labeled with a black dot. Double-check that
you connected amplifier + to speaker + and amplifier
to speaker .
4. Make sure all the
RotoLock clamps are
retracted so that
they are tucked within
the mounting holes bor-
der. Insert the speaker
into the hole in the ceil-
ing (
Figure 4
). The
RotoLock system can
accommodate a maxi-
mum ceiling material
thickness of 1¼
(32mm).
The FastMount tabs
will prevent the speak-
er from falling out of
the mounting hole,
allowing you to let go
of the speaker to pick-
up tools or other items
(
Figure 5
).
N F MOTE : THE A ST OU N T
TAB S A RE DE SIG NE D FOR
ON E T IM E U S E ON LY- . IF
THE SPEAKER IS REMOVED
F R O M T H E M O U N T I N G
HOLE THE ASTF MO U NT
TABS WILL D ISCON NE CT
AN D RE MAIN INSIDE THE
CE ILING .
5. Tighten the four screws
on the front of the
speaker baffle. The
Roto-Lock clamps will
automatically rotate
into position and begin
clamping the speaker
(
Figure 6
).
When you notice
resistance on the
screws the speaker
has been clamped
successfully.
I M P O R T A N T :
Always use low-
torque settings;
NEVER over-tighten.
N ROTE : ADJ U ST T HE TE N SI ON OF TH E OTO -LOCK CLAM PS SO
THAT THE SPEAKE R FRAME IS FL AT. TH IS W IL L H EL P E NSU R E TH AT
THE G RILL E CON TACTS THE C EI LIN G A LL THE W AY AROU ND THE
SPEAKE R FOR A PROP ER F IT.
FastMount Tabs
Roto-Lock Clamps
(retracted)
F SIGURE 4: INSERTING THE PEAKER
INTO THE OUNTING OLEM H
F 5:IGURE
FAST OUNTM TABS
Roto-Lock Screws
F 6:IGURE
TIGHTENING THE ROTOLOCK CREWSS
3
SONANCE VISUAL PERFORMANCE ®LARGE ROUND AND SQUARE
6. The new micro-trim grille is held in place by several small,
powerful magnets on the speaker frame. Place the grille
against the speaker and the magnets will hold it firmly in
place. When properly installed, the grille trim should make
contact with the wall all the way around the speaker.
Painting The Grilles
Please see the accompanying
Painting Instructions
sheet for
painting instructions.
Speaker Adjustments
Pivoting Woofer and Midrange/Tweeter
Some Visual Performance Series Large round and square speak-
ers have a pivoting woofer and a pivoting midrange/tweeter
assembly. If youre using the speakers in stereo or as the front
left/center/right speakers in a home theater, pivot the drivers
directly towards the listening area. If youre using the speakers
as surround channel speakers in a home theater, pivot the
drivers towards a wall or window, away from the listeners.
To pivot the midrange/tweeter assembly, apply light pressure to
the ring around the outside edge of the midrange cone, as shown
in
Figure 7
. Take care not to touch or apply pressure to the
midrange cone itself. To Pivot the woofer, apply pressure on the
outer edge of one of the tweeter support brackets, as shown in
Figure 7
. Do not touch or apply pressure to the woofer cone.
Tweeter and Midrange Level Switches
VP89 and VP87 speakers have midrange and tweeter level
switches (see
Figure 8
) that boost or cut those drivers levels by
3dB. This lets you tailor the speaker’s performance to better
match the rooms acoustics or the listeners preferences.
FIGURE 7: PIVOTING THE IDRANGE WEETER SSEMBLY LEFTM /T A ( )
AND THE OOFER RIGHTW ( )
Midrange Level
Switch Tweeter Level
Switch
F T L SIGURE 8: MIDRANGE AND WEETER EVEL WITCHES


Product specificaties

Merk: Sonance
Categorie: Speaker
Model: Visual Performance VP85S SST

Heb je hulp nodig?

Als je hulp nodig hebt met Sonance Visual Performance VP85S SST stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Sonance

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Creative

Creative Muvo 1C Handleiding

24 December 2024
Savio

Savio BS-03 Handleiding

24 December 2024
Adam

Adam S3V Handleiding

23 December 2024
Adam

Adam S5V Handleiding

23 December 2024
Adam

Adam S2V Handleiding

23 December 2024
Adam

Adam S3H Handleiding

23 December 2024
Adam

Adam S5H Handleiding

23 December 2024
Adam

Adam T5V Handleiding

23 December 2024
Adam

Adam F7 Handleiding

23 December 2024