Sonance Visual Performance VP65 XT Handleiding

Sonance Speaker Visual Performance VP65 XT

Lees hieronder de 📖 handleiding in het Nederlandse voor Sonance Visual Performance VP65 XT (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
1
Introduction
Thank you for purchasing Sonance Visual Performance Series
Extreme Speakers. These weatherproof 6" speakers can provide
superior sound quality for high-humidity areas and are built to
survive temperature extremes from –30°F – +175°F (–34°C –
+79°C). Their shallow depth makes them easy to install in a vari-
ety of challenging spaces. Visual Performance Extreme speakers
provide excellent sound in yachts, saunas, steam rooms, and hot
tub areas.
This manual covers the following speaker models: VP65 XT
(rectangular), VP65R XT (round), VP65S XT (square), VP65R SST
XT (round, Single-Stereo Technology ®).
Box Contents
Sonance VP65 XT, VP65R XT, and VP65S XT speaker boxes contain
(2) speakers, (2) paint plugs (installed on the fronts of the
speakers), (2) paintable grilles and (1) mounting cutout
template.
Sonance VP65R SST XT speaker boxes contain (1) speaker,
(1) plastic paint plug (installed on the front of the speaker),
(1) paintable grille and (1) mounting cutout template.
Speaker Placement
St e r e o Sp eake r P la ce me nt ( VP 65 X T)
• Place the left and right speakers on the same wall, from 6 to
10 feet (1.8 – 3m) apart.
• If the listeners will be seated the speakers should be located
38 – 42 (97 – 107cm) inches from the floor.
• If listeners will be standing the speakers should be located
5 feet (1.5m) from the floor.
• The ideal listening distance will be between 4 and 10 feet (1.2
and 3m) away from the speakers. The best stereo performance
will be midway between the speakers.
Use Figure 1 (next column) as a guide
D i st r i bu te d A ud i o P la c em en t
(V P 6 5 R X T/ V P 6 5S X T/ V P 6 5R SS T X T)
Sonance VP65R XT, VP 65S XT and VP65R SST XT in-ceiling
speaker models provide excellent coverage in distributed
audio systems from a wide variety of installation locations.
The table and illustration in show how far apart Figure 2
speakers can be placed at various ceiling heights while still
providing good coverage for all listeners.
The VP65R SST XT reproduces both stereo channels from a single
location, making it ideal for use in bathrooms, saunas, or in any
location where a pair of stereo speakers would be impractical.
Before Installation: Retrofit
1. Determine the location for the speaker (see Speaker
Placement on page 1).
2. Perform an obstruction survey to be certain that there are
no studs, conduit, pipes, heating ducts, pocket doors or
air returns in the wall cavity that will interfere with the
speaker.
I N S T R U C T I O N M A N U A L
V I S UA L P E R F O R M A N C E ® S E R I E S
E X T R E M E S P E A K E R S
S W :A F E T Y A R N I N G
T F MHESE SPEAKERS HAVE AST OUNT®TABS THAT PREVENT THE
SPEAKER FROM FALLING OUT OF THE MOUNTING HOLE DURING THE
INSTALLATION PROCESS.
T F MH E E D G E S O F T H E A S T O U N T T A B S A R E V E R Y S H A R P.
US E C A U T I O N W H E N H A N D L I N G T H E S P E A K E R .
C OVERAGE
AREA COVERAGE
AREA
S PEAKER
SPACING
S )PEAKER S (PACING IN FEET
FOR ISTRIBUTED UDIO YSTEM A D A S
STANDING LISTENER SEATED LISTENER
10-
FOOT CEILING
12-
FOOT CEILING
14-
FOOT CEILING
8-
F 9.5’ (2.9m) ApartOOT CEILING
13.5’ (4.1m) Apart
17.5’ (5.3m) Apart
21.5’ (6.6m) Apart
5.7’ (1.7m) Apart
9.7’ (3.0m) Apart
13.7’ (4.2m) Apart
17.7’ (5.4m) Apart
F A S SIGURE 2: DISTRIBUTED UDIO PEAKER PACING
38” – 42”
(97cm – 107cm)
(Seated Listeners)
5‘ (1.5m)
(Standing Listeners)
6‘ – 10’ (1.8m – 3m)
Apart
F S PIGURE 1: STEREO PEAKER LACEMENT
2
SONANCE VISUAL PERFORMANCE®EXTREME SPEAKERS
3. VP Extreme speakers require the following mounting cutouts:
• VP65 XT: 615
/16” (176mm) wide by 10¾” (273mm) high, with
at least 2½” (64mm) of depth within the mounting cavity.
• VP65R XT: 8¼” (210mm) diameter, with at least 3½”
(89mm) of depth within the mounting cavity.
• VP65S XT: 8¼” (210mm) wide by 8¼” (210mm) high, with at
least 3½” (89mm) of depth within the mounting cavity.
• VP65R SST XT: 8¼” (210mm) diameter, with at least 3½”
(89mm) of depth within the mounting cavity.
4. Position the included mounting cutout template where the
speaker is to be located and pencil an outline on the wall
or ceiling.
• If you are unsure about obstructions, drill a small hole in
the center of the outline and insert a coat hanger wire into
the hole to feel-around for possible obstructions.
5. Cut the mounting hole using tools appropriate for the
construction, and run the speaker wires from the mounting
hole to the amplifier location.
• Consult local building codes before running speaker wires
through walls.
Installation
Sonance VIsual Performance Series Extreme speakers feature
exclusive FastMount®tabs and an integral RotoLock®mounting
system for quick mounting directly into existing walls and ceilings.
WA R N I N G : T HE E D G E S O F T H E FA S T M O U N T TA B S
A R E V E R Y S HA R P. U S E C A U T ION W H E N H A N-
D L I N G T H E S P E A K E R .
1. Remove the paint plug from the speaker.
2. Strip ¼” – ½” (6mm – 13mm) of insulation from each
speaker lead. Twist the strands or tin the exposed wire
with solder to ensure that there are no stray strands.
(Stray strands that touch each other can cause a short-
circuit that can damage the amplifier.)
3. The speaker’s connector posts are spring-loaded. Push the top
of each connector post down to open the connector and insert
the exposed wires into the holes in the posts (see Figure 3).
• The speaker’s positive post is labeled with a red dot; the
negative post is labeled with a black dot.
• The VP65R SST XT has two sets of connection terminals,
located on opposite sides of the crossover board.
• After making all connections, double-check that you
connected amplifier “+” to speaker “+” and amplifier “–”
to speaker “–”.
4. As shipped, the RotoLock clamps can accommodate a max-
imum wall or ceiling material thickness of 1¼” (32mm).
NOTE: IF YOU’RE INSTALLING THE VP65R XT, VP65S XT, OR
VP65R SST XT INTO CEILING MATERIAL THAT IS THICKER THAN
1¼” (32MM YOU CAN REMOVE THE FEET OF THE OCK), ‘ ’ ROTOL
CLAMPS, WHICH WILL ALLOW YOU TO CLAMP THE SPEAKER TO CEIL-
ING MATERIAL THAT IS UP TO MM THICK1¾” (44 ) . TO REMOVE THE
CLAMP FEET
, USE A SMALL SCREWDRIVER TO GENTLY RELEASE THE
LO CKING LEVERS (F 4IGUR E , LEFT). THEN REMO VE THE FEET FROM
THE CLAMPS (F 4IGUR E , ).RIGHT
5. Make sure all the RotoLock clamps are retracted so that they
are tucked within the mounting hole’s border. Insert the
speaker into the mounting hole ( , left). TheFigure 5
FastMount tabs will prevent the speaker from falling out of
the mounting hole, allowing you to let go of the speaker to
pick-up tools or other items ( , right).Figure 5
NOTE: THE AST OUNT TABS ARE DESIGNED FOR ONE TIME USEF M -
ONLY. IF THE SPEAKER IS REMO VED FROM THE MO UNTING HOLE THE
F MAST OUNT TABS WILL DISCONNECT AND REMAIN INSIDE THE WALL
OR CEILING.
6. Tighten the four screws on the front of the speaker baffle. The
RotoLock clamps will automatically rotate into position and
begin clamping the speaker ( , page 3).Figure 6
FastMount
Tabs
RotoLock Clamps
(retracted)
F SIGURE 5: INSERTING THE PEAKER INTO THE OUNTING OLEM HF TIGURE 3 CONNECTION ERMINALS
Connection Terminals
(1 Set on VP65R XT, VP65S XT, VP65 XT;
2 Sets on VP65R SST XT)
FastMount
Tabs
Locking Lever
Remove Foot
F R LIGURE 4: REMOVING THE OTO OCK LAMP EETC F
3
SONANCE VISUAL PERFORMANCE®EXTREME SPEAKERS
• When you notice resistance on the screws the speaker has
been clamped successfully.
IM P O RTAN T : A L WAY S U SE L O W T O R Q U E S E T T I N G S- ;
NEVER O V E R -T I G H T E N .
N R LOT E : AD J US TI N G TH E T EN SI O N O F T HE OTO O C K C L AM PS S O
THAT T HE SPEA KER FRAME IS F LAT WIL L HEL P EN SU RE THAT T HE GRI LL E
C O N TA C TS T HE W A LL A L L T H E W AY A RO U ND T HE S PEA KE R F O R A
P RO P ER F IT.
7. The new micro-trim grille is held in place by several small,
powerful magnets on the rear of the grille. Place the grille
against the speaker and the magnets will hold it firmly in
place. When the grille is properly installed, the grille trim
should make contact with the mounting surface all the way
around the speaker.
Painting the Grilles
See the accompanying instruction sheet for painting instructions.
Environmental Specifications
Maximum Heat: +175°F (+79°C)
Maximum Cold: –30°F (–34°C)
Maximum Humidity: 99% (120°F/49°C)
95% (–30°F/–34°C)
These speakers meet or exceed the foll owing:
Salt Spray: ASTM-B117
UV Test: ASTM-G23H
IEC/CEE
Water Splashing Test: IP-X4
Vibration Test: ASTM D5112-98 and ASTM D3580-95
Performance Specifications
V P 6 5 X T
Tweeter: 1" (25mm) polyurethane dome
Woofer: 6½" (165mm) injection-molded
polypropylene/graphite cone, with
integral Santoprene ®surround
Frequency Response: 55Hz – 20kHz ±3dB
Impedance: 8 ohms nominal; 6 ohms minimum
Power Handling: 5 watts minimum; 130 watts maximum
Sensitivity: 89dB SPL (2.83V/1 meter)
Grille Material: Powder-coated stainless steel
Dimensions (W x H x D): 83/8" x 12¼" x 2½”
(213mm x 311mm x 64mm)
Cutout Dimensions (W x H): 615
/16” x 10¾" (176mm x 273mm)
Shipping Weight: 12 lbs (5.4kg) pair
V P 6 5 R X T
Tweeter: 1" (25mm) polyurethane dome
Woofer: 6½" (165mm) injection-molded
polypropylene/graphite cone, with
integral Santoprene ®surround
Frequency Response: 55Hz – 20kHz ±3dB
Impedance: 8 ohms nominal; 6 ohms minimum
Power Handling: 5 watts minimum; 130 watts maximum
Sensitivity: 89dB SPL (2.83V/1 meter)
Grille Material: Powder-coated stainless steel
Dimensions (Dia x D): 9¾” x 3½” (248mm x 89mm)
Cutout Dimensions (Dia): 8¼” (210mm)
Shipping Weight: 12 lbs (5.4kg) pair
V P 6 5 S X T
Tweeter: 1" (25mm) polyurethane dome
Woofer: 6½" (165mm) injection-molded
polypropylene/graphite cone, with
integral Santoprene surround
Frequency Response: 55Hz – 20kHz ±3dB
Impedance: 8 ohms nominal; 6 ohms minimum
Power Handling: 5 watts minimum; 130 watts maximum
Sensitivity: 89dB (SPL 2.83V/1 meter)
Grille Material: Powder-coated stainless steel
Dimensions (H x W x D): 97/8" x 97/
8” x 3½"
(251mm x 251mm x 89mm)
Cutout Dim. (W x H): 8¼" x 8¼" (210mm x 210mm)
Shipping Weight: 12 lbs. (5.4kg) pair
V P 6 5 R S S T X T
Tweeter: Two 1" (25mm) polyurethane domes
Woofer: 6½" (165mm) injection-molded
polypropylene/graphite cone, with
integral Santoprene ®surround, dual
voice coil
Frequency Response: 55Hz – 20kHz ±3dB
Impedance: 8 ohms nominal; 6 ohms minimum
Power Handling: 5 watts minimum; 130 watts maximum
Sensitivity: 89dB SPL (2.83V/1 meter)
Grille Material: Powder-coated stainless steel
Dimensions (Dia x D): 9¾” x 5 3
/16” (248mm x 132mm)
Cutout Dimensions (Dia): 8¼” (210mm)
Shipping Weight: 4.5 lbs (2.1kg) each
RotoLock
Screws
F R LIGURE 6: TIGHTENING THE OTO OCK CREWSS

Product specificaties

Merk: Sonance
Categorie: Speaker
Model: Visual Performance VP65 XT

Heb je hulp nodig?

Als je hulp nodig hebt met Sonance Visual Performance VP65 XT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker Sonance

Sonance

Sonance Mariner MX52 Handleiding

12 November 2024
Sonance

Sonance Mariner MX66 Handleiding

11 September 2024
Sonance

Sonance MAG06V3 Handleiding

27 Juni 2024
Sonance

Sonance Garden SGS Subwoofer Handleiding

9 Juni 2023
Sonance

Sonance Visual Performance VP61 Handleiding

31 Mei 2023
Sonance

Sonance IS4 Handleiding

27 Mei 2023
Sonance

Sonance Patio SR 2-125 Handleiding

14 Mei 2023
Sonance

Sonance Visual Performance VP85S SST Handleiding

5 Mei 2023
Sonance

Sonance Visual Performance VP83 Handleiding

1 Mei 2023
Sonance

Sonance Landscape HS12T SUB Handleiding

30 April 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Kenwood

Kenwood KFC-PS170C Handleiding

3 December 2024
Bose

Bose DesignMax DM5P Handleiding

2 December 2024
Yamaha

Yamaha CHR12 Handleiding

2 December 2024
Yamaha

Yamaha DHR12 Handleiding

2 December 2024
Yamaha

Yamaha DHR15M Handleiding

2 December 2024
Yamaha

Yamaha CHR15M Handleiding

2 December 2024
Yamaha

Yamaha True X Speaker 1A WS-X1A Handleiding

2 December 2024
Yamaha

Yamaha Stagepas 100 Handleiding

2 December 2024
Yamaha

Yamaha NS-2000A Handleiding

2 December 2024
Yamaha

Yamaha DXS15XLF-D Handleiding

2 December 2024