Smeg WDI12C1 Handleiding

Smeg Wasmachine WDI12C1

Lees hieronder de 📖 handleiding in het Nederlandse voor Smeg WDI12C1 (9 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

ISTRUZIONI DI MONTAGGIO DELLE

LAVATRICI INTEGRABILI

ASSEMBLY INSTRUCTIONS FOR BUILT-IN WASHING

MACHINES

MONTAGEANLEITUNG FÜR EINBAUBARE-

WASCHMASCHINEN

INSTRUCTIONS DE MONTAGE DES LAVE-LINGE

INTÉGRABLES

INSTRUCCIONES DE INSTALACIÓN DE LAS

LAVADORAS INTEGRABLES

INSTRUÇÕES DE MONTAGEM DAS MÁQUINAS DE

LAVAR ROUPA INTEGRÁVEIS

MONTAGEINSTRUCTIES VAN INTEGREERBARE

WASMACHINES

MONTERINGSANVISNING FOR INTEGRERBARE

VASKEMASKINER

MONTERINGSANVISNINGAR FÖR

INBYGGNADSBARA TVÄTTMASKINER

ANKASTRE ÇAMAŞIR MAKĐNELERĐ

ĐÇĐN MONTAJ TALĐMATLARI

ASSEMBLY INSTRUCTIONS FOR BUILT-IN WASHING MA-

CHINES

IMPORTANT This machine complies with current safety regulations govern--

ing electrical appliances and, to ensure user safety, it must be installed by a

qualified technician as required by current legislation

Size of cabinet

The minimum dimensions of the cabinet are: height mm, 820

width mm, depth mm ( ).600 584 fig. 1

Applying the

panel

The panel may be attached to the left- or right-hand side of the

washing machine ( ) fig. 2

The machine is supplied fitted for a left-hand side panel at-

tachment as the right-hand side is fitted with the push-pull lock

(upper part) and the rubber pad (lower part).

Should you wish to use the magnetic lock instead of the push-

pull lock, remove the push-pull lock support and fit the supplied

magnetic lock support.

Important! Before fitting the panel (removing all the hinge

and locking elements from the front) make sure the wash-

ing machine is totally disconnected from the mains power

supply.

Warning - To fix the panel on the right-hand side (direction of

opening opposite to that of the door) dismount the push-pull

lock (or the magnet lock) from the front of the machine and the

rubber pad ( ) and fit them on the opposite side (fig. 3-A fig. 3-

B).

All the elements applied to the front of the washing machine

must be remounted correctly (no holes must remain open) in

order to make it impossible to touch live components inside the

machine.

Our company declines all liability for failure to observe the

above safety requirement.

Using the tem-

plate

1) Measure the height of the kitchen baseboard: the height of

the wooden panel is obtained by first establishing the height

of the kitchen baseboard.

E.g.: for a mm high baseboard, the maximum height of 100

the panel is mm. If the height of the baseboard must be 720

increased, the height of the wooden panel must be reduced.

Place the template of the inner side of the panel and match the

height of the baseboard with the lower edge of the panel ( ) fig. 4

using the graduated scale. Make sure the template is horizon-

tally centred with reference to the vertical lines marked at the

ends.

After placing the template in the correct position, trace the posi-

tions of the following holes, pushing in with the tip of your pen-

cil:

• holes for the hinges and hinge screws ( ) fig. 4

•

holes for fixing the metal plate (if the magnetic lock is

used), or the hook for the push-pull lock ( )fig. 4, A - B

Applying the

panel elements

and fixing the

panel

1) Drill the holes for the hinges ( ), the hook for the push-fig. 5

pull lock ( ), or the metal plate if you decide to use the fig. 5

magnetic lock ( ), and the holes for fixing the hinges fig. 6

( ). fig. 6

2) The 13 mm depth of the 2 mm holes, for fixing the hinges

and a metal plate for the magnet lock, only applies to the

solid wood chipboard panel panel. For the , simply drill the

upper coating – fig. 6.

3) Screw the two hinges to the panel ( ) fig. 7

4) Mount the hook for the push-pull lock or the metal plate for

the magnet lock on the side opposite the hinges ( ). fig. 7

5) Fix the panel to the washing machine following the instruc-

tions shown in . fig. 8

Adjusting the

hinges

If, after applying the panel to the washing machine, it is slightly

inclined or off-centre with respect to the front of the machine,

correct its position by adjusting the mobile part of the hinges

(fig. 9).

Positioning the

washing ma-

chine in the

cabinet

Position the washing machine in the cabinet and, if necessary,

adjust the feet to level it and lock them with the relative locknut.

To prevent the vibrations generated by the washing machine

from being transmitted to the cabinet, make sure the sides and

top do not touch the cabinet. There must be a gap of at least

2 mm. The back of the machine must also remain detached

from the rear panel.

If the cabinet is 870 mm high, the washing machine height-

ening kit on sale from the Spare Parts Service, must be

used.

To comply with safety legislation, any gaps between the floor

and the bottom of the baseplate and between the floor and the

sides of the machine when it is positioned at the end of a line of

furniture must be completely closed.

The cover must be installed in such a way as to make it

impossible to touch live components and a tool must be

Product specificaties

Merk:	Smeg
Categorie:	Wasmachine
Model:	WDI12C1
Apparaatplaatsing:	Ingebouwd
Kleur van het product:	Black, White
Ingebouwd display:	Ja
Timer:	Ja
Breedte:	596 mm
Diepte:	575 mm
Hoogte:	820 mm
Type lader:	Voorbelading
Deurkleur:	Wit
Energie-efficiëntieklasse (oud):	C
Geschikt voor paneelaanpassing:	Ja
Energieverbruik wassen:	0.95 kWu
Waterconsumptie per cyclus:	47 l
Wasklasse:	A
Maximale centrifugesnelheid:	1200 RPM
Deur open alarm:	Ja
Deurpaneel inbegrepen:	Nee
Aantal wasprogramma's:	14
Verstelbare voeten:	Ja
AquaStop-functie:	Ja
Spoelstop:	Ja
Nominale capaciteit:	5 kg
Wasprogramma's:	Hygiene/anti-allergy, Black