Smeg KSED95P Handleiding

Smeg Afzuigkap KSED95P

Lees hieronder de 📖 handleiding in het Nederlandse voor Smeg KSED95P (8 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 181 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

WARNING!

• Read the instructions carefully before installing and/or using the hood.

• Before connecting, make sure that the mains voltage corresponds to the voltage on

the rating plate inside the hood. (see fig. 7)

• Once you remove the appliance from its packaging make sure it is intact. If the

product is damaged, do not use it and contact the Smeg assistance network.

• It is recommended that a qualified technician performs installation and adjustment

operations .

• The minimum distance between the cooker and the lower part of the hood must be

750mm for gas cookers and 650 mm for electric cookers.

• Before carrying out any kind of maintenance or cleaning, disconnect the hood from

the mains supply.

• Inspect and clean the filters thoroughly and in accordance with the intervals

suggested by the manufacturer.

• Do not cook or fry in a way that could result in flames being sucked into the hood and

causing a fire.

• The hood surface can be cleaned with a damp cloth and a non-bleach liquid

detergent.

• Make sure the room is properly ventilated when using the hood and other gas

appliances at the same time.

• Comply with the regulations on air discharge when operating the hood.

• The extracted air must not be routed into a duct used to discharge fumes of gas-

operated appliances.

• This appliance must not be used by children without an adult supervision

and disabled people may require assistance.

• THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THE ABOVE

INSTRUCTIONS ARE NOT FOLLOWED.

OPERATION

This appliance has been designed to work as a

DUCTING

hood (evacuation of the

air) or RECYCLING hood (recycling of the filtered air).

• DUCTED MODE: In order to use the hood in the ducted mode, connect the motor

intake, by means of a suitable ducting hose not less than 120mm diameter, directly to

the external fumes outlet.

Note: Remove any carbon filters.

• RECIRCULATION MODE: If it is not possible to discharge fumes outside, the hood

can be used to filter and recycle the air. This way, air and fumes are filtered by the

anti-odour carbon filters and recirculated through the aerating grids on the sides of

chimney.

EN 01

INSTALLATION INSTRUCTIONS:

The hood is supplied with all the necessary

accessories for installation. The minimum distance

between the cooker and the lower part of the hood

must be 750 mm for gas cookers and 650 mm for

electric cookers (Fig. 1). The hood is supplied with a

motor intake (Fig 2). If it has not been assembled by

the manufacturer, you can assemble it using the

supplied screws (for type 1) or pushing (for type 2)

If the motor intake is equipped with a non-return

valve, make sure it opens and closes perfectly.

The following instructions will assist installation:

a) The hood should be centred with respect to the

cooker.

The hood is supplied with two supports/hooks (a)

(Fig 3) or bracket (b) that need to be fixed to the

wall by means of wall anchors . The L1 holes for

these supports are on the back of the hood (fig.

Remove the anti-grease filters, put the hood on

the wall and mark the position of the holes for the

supports/hooks.

d) Drill the two previously marked holes after

removing the hood from the wall.

e) Fix the two supports/hooks to the wall.

f) Mark the L2 holes on the wall to fix the hood

safely. (fig. 4) Drill and put the anchors in the

holes.

g) Hang the hood on to the supports/hooks (fig. 5)

and level by means of the adjusting screw

(fig.3).

h) Fix the hood safe by tightening both wall anchors.

Ducted mode or Recirculation mode installation:

Ducted mode:

In the ducted mode, connect the motor outlet to the

fumes outlet duct not less than 120mm diameter.

Warning: if the hood is equipped with an active

carbon filter, it must be removed (see page 7)

EN 02

Fig.2

Hood levelling screw

Fig.3

Type 1

Type 2

Fig.1

(a)

(b)

Recirculation mode:

Leave the motor intake free. Install the active carbon

filters as shown in page 6.

Warning: if the hood is not supplied with an active

carbon filter, it is necessary to buy it separately and

assemble it before using the hood.

i) Chimney assembly:

Adjust the two telescopic chimneys to the required

length (fig. 6).

Secure the chimneys by tightening the two H screws.

Place the chimney group on the top side of the hood

carefully. Put the chimney bracket

on the

chimney (fig. 6). Mark the holes on the wall for fixing

the chimney bracket to the wall.

Remove the chimney set, drill and fix the support

bracket to the wall by means of wall anchors. Put the

chimney group back in place and fix it to the hood with

the Z screws and to the chimney bracket with the L

screws as shown in figure 6.

ELECTRICAL CONNECTION

It is recommended that all electrical connection

operations are performed by a qualified technician.

The appliance is supplied WITHOUT A PLUG. It is

therefore necessary to fix a plug to the cable or hard

wire direct to a spur. The plug and fuse must be in

accordance with the rating plate inside the hood. Then

connect it to a nearby, easily reachable socket in

accordance with the rules in force.

In the case of a direct connection to the mains supply,

it is necessary to put a switched spur between the

appliance and the mains supply. The switch must be

suitable for the load, compliant with the rules in force

and must have a minimum contact opening of not less

than 3mm.

EN 03

OPERATING INSTRUCTIONS

Fig.4

Fig.5

Fig.6

Product specificaties

Merk:	Smeg
Categorie:	Afzuigkap
Model:	KSED95P
Kleur van het product:	Crème
Breedte:	900 mm
Diepte:	515 mm
Hoogte:	840 mm
Geluidsniveau:	52 dB
Soort:	Muurmontage
Motor vermogen:	240 W
Aantal motors:	1
Materiaal behuizing:	Roestvrijstaal
Maximale afzuigcapaciteit:	700 m³/uur
Afzuigmethode:	Afvoerend/recirculerend
Aantal lampen:	2 gloeilamp(en)
Soort vetfilter:	Metaal
Aantal filters:	3 stuk(s)
Aantal snelheden:	3