Smartwares VD38W Handleiding

Smartwares Bewakingscamera VD38W

Lees hieronder de 📖 handleiding in het Nederlandse voor Smartwares VD38W (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

14 15 16 12

13 17 18 9 10

211

OPTIONAL:

TOWARDS THE

DOOR LOCK

3 4 5

12V 1Amp MAX

Always test the product on site before installation.

Be aware that different materials in between the Outdoor Intercom

and Indoor Monitor will affect the operating performance of the product.

Follow the Wiring and pairing guides to test the product.

Install the Outdoor Intercom in a dry location if possible.

Mount the Intercom at a suitable height and position to allow the

camera to see the visitor

Battery setup:

Outdoors intercom

1. On the back of the intercom, remove the 6 screws on the battery

compartment, and remove the cover

2. Insert the battery pack into the compartment, making sure it is positioned

correctly, with the marking "Rechargeable Li-Ion battery" facing you.

3. Replace the battery compartment cover and insert the 6 screws.

Indoor Monitor

1. On the back of the indoor monitor, open the battery compartment

cover pulling towards you.

2. Insert the battery pack into the compartment, making sure it is positioned

correctly, with the marking "Rechargeable Li-Ion battery" facing you.

3. Replace the compartment cover.

Installation and setup Outdoor intercom wall support

Key features

CAUTION

1. Please read these instructions before setting up and using the device.

2. Do not cut the power supply cable to extend it; the transformer will not operate with

a longer cable. Do not plug in the transformer until all the wiring has been finished.

3. This product is not a toy. Keep it out of reach of children.

4. Do not operate electrically powered products in explosive atmospheres, such as

in the presence of flammable liquids, gases, or dust. Electrically powered products

may create sparks which are likely to ignite dust or create fumes.

5. The warnings, precautions, and instructions presented in this instruction manual

cannot cover all possible conditions and situations that may occur the operator must

understand that common sense and caution are factors that the product can not

provide but the operator must put in place.

6. Do not expose the power adapter for this product to rain or moisture.

Water entering the Power Adapter will increase the risk of electric shock.

7. Do not abuse the Power Cord. Never use the cord for unplugging the plug from the outlet.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. The adapter must match the power outlet.

Never modify the cord in any way. Unmodified plugs and suitable outlets will reduce

risk of electric shock.

1. Antenne

2. Screen

3. UP button

4. LEFT button

5. RIGHT button

6. OK / Photo button

7. DOWN button

8. Intercom button

9. Door lock button

10. Monitor button

11. Microphone

12. LED lighting

13. USB port

14. Power ON/OFF

15. Metal support screws

16. Metal supports

17. Wall mount

18. Battery compartment cover

1. Rain cover

2. Microphone

3. Camera lens

4. Night vision lighting

5. Speaker

6. Name plate

7. Call button

8. Light sensor

9. Antenne

10. Battery compartment

11. Screw

12. Power and locking connector

Included in the pack:

Inside

Indoor Monitor Outdoors intercom

Outside

OPTIONAL

1. Select the location of the outdoor intercom, use the rain cover as a

template anD drill the holes to mount the plugs.

2. Mark and drill the hole in order to feed the electric cables through the wall.

3. Push the electric cables so that they are visible from the outside.

4. Glue the seal inside the rain cover.

5. Mount the rain cover with the mounting hardware included.

Pay attention to the mounting bracket on the lower support,

making sure the electric cables will fit through the joining

opening of the back plate in the lower corner.

6. Link the intercom electric cables as shown on the wiring diagram below.

7. Firstly, insert the upper part of the intercom into the rain cover and

place the lower part on the angled support.

8. Secure the intercom in place on the rain cover using the securing screws.

Name plate

1. If you need to fill the name plate, push strongly on the left side whilst

sliding the plate to the left in order to free the right side and then remove it.

2. Use a pointy object to remove the name plate from the inside of the

plate and fill-in your details.

3. Then, replace the label and follow the same steps in the opposite

order to reassemble the plate in the outdoor unit.

1. With a small screw driver, push the connexion bloc upwards on

the outdoor intercom in order to detach it.

2. Connect the DC power supply to the terminals marked + and -,

checking that the wires are linked correctly.

3. If required, connect the door lock cables to the 2 terminals, checking

the correct power supply to the door lock (only for an electric door lock,

max. 12 V, 1 A , through a separate power plug - NOT INCLUDED).

4. Replace the connector in the outdoor intercom, making sure the

polarity is correct.

Name plate Wiring

13-20mm

118mm

Intercom:

When a visitor pushes the DOWN button on the outdoor camera,

the indoor monitor activates the doorbell and the monitor screen.

The monitor screen transmits automatically the image of the visitor.

Push the intercom button (8) and talk to the visitor.

Push TWICE on the monitor button (10) and the screen goes

into standby mode.

Monitor:

The monitor button (10) can be used to turn the screen on and

access its functions. You can use this button to see who is behind

the door if the outdoor DOWN button hasn't been pushed.

This function only works if the outdoor intercom is powered on the mains.

Unlock:

Once the visitor is identified, push the door lock button (9) to unlock

the door. (Only for opening an electric door, max 12 V 1 A , from an

external separated power supply, NOT INCLUDED).

Technical specifications

NOTES

Do not leave the product on uneven surfaces to prevent damage cause by falling.

Avoid placing the product on hot, dusty or humid surfaces, exposed to sea salt and weather

since the life of the device will be reduced.

The device must not be exposed to splashing or other liquids, and no object containing water,

such as vases, must be placed on the device.

When the DC adapter is used as a safety device, it must remain easily accessible.

CAUTION

Explosion risk if the battery is not replaced properly. Only replace the battery with a similar

battery or a battery of similar type.

The battery must not be exposed to excessive heat, such as sun light, fire or similar.

Do not cover the ventilation openings with objects such

as newspaper, table cloths, curtains, etc.

Do not allow this product to get directly into contact with

heat sources or naked flames.

The normal operation of the product may be disturbed by

strong electro-magnetic interference.

This equipement is built exclusively for a domestic use.

The device must not be exposed to splashes and it must

not be submerged.

No object containing liquids, such as a vase, may be

placed on the device.

Maintain a minimum safety distance of 10cm all around the

product in order to insure proper ventilation.

Insure the doorbell push button is not installed where it may

be covered by water or rain.

Do not allow children to play with the device.

Only an adult may replace and install batteries.

Remove used batteries from this device.

Do not dispose of batteries in fire,they may explode or leak.

Do not short-circuit battery terminals.

DO not use any other type of battery other than the

rechargeable pack supplied or similar.

Do not allow this device to get directly into contact with

heat sources or flames.

Do not allow water to enter into contact with the

batteries or the wires.

Install with caution to avoid damaging the batteries.

During battery installation in their compartment, insure

proper polarity (+)/ (-).

Only use recommended batteries.

Remove the batteries if the device remains unused

for long periods.

Keep the device away from small children.

Keep the unused batteries in their original packaging.

At the end of its life, this product must be returned to a

waste processing center in order to extract the batteries.

Precaution

Warning about batteries

Troubleshooting Security information

Screen iconsRecharge and wall mounting of the indoor monitor

MATERIAL RANGE GUIDE

More details

Monitor status indicator

Signal indicator

Intercom status indicator

Call status indicator

Volume indicator

Indoor monitor battery indicator

Outdoor monitor battery indicator

Taking a photo:

1. When a visitor pushes the DOWN button on the outdoor intercom,

the indoor monitor automatically takes a photo.

2. On the indoor monitor, press the OK/Photo button (6)

in order to take another picture of the visitor.

View the photo:

1. On the indoor monitor, press the Up (3) or DOWN (7) button

to view the recorded photo.

2. Press the right button (5) pour display the deletion dialog box.

Press the OK/Photo (6) button to confirm.

3. Push the intercom button (8) to quit.

Doorbell ring setup:

1. Push the monitor button (10) to turn on the screen

2. Press the Left (4) or Right (5) button to select the doorbell

3. Push the monitor button (10) to quit.

4. You can choose between 16 melodies.

Operation

Specifications :

Operating frequency : 2400-2483.5MHz

Transmission rate : 15-25fps

Operating rate without obstacles : 120m

Transmitted power : 14 - 18dBm

Reception sensitivity : -85dBm

Operating temperature : -10°c - +50°c

Operating humidity : ≤85% RH

Outdoors intercom P513T

Picture sensor type : CMOS

Viewing angle : 45°

Power supply : DC 5V 1A

Battery : 3.7V / 1500mAh

Power consumption : 300 ± 50mA

Recharge time : Approx. 5 hours

Operating time : 5 operations per day -

20 days before recharge

Adapter INPUT: 100-240V~50/60Hz 0.3A

OUTPUT: 5.0V 1.0A

Indoor Monitor M335T

Screen size : 3.5"

Resolution : 320 x 240 (RGB)

Power supply : DC 5V 1A

Battery : 3.7V / 1500mAh

Power consumption : 350 ± 50mA

Recharge time : Approx. 5 hours

Image format : JPEG

Operating time : 5 operations per day

- 20 days before recharge

Adapter INPUT: 100-240V~50/60Hz 0.3A

OUTPUT: 5.0V 1.0A

Test the doorbell before drilling the holes in order to check if

the unit is within the working range.

The wireless working range may be affected by some

materials or structures. Test before installation.

80-95%

90-100%

120m

60-80%

0-20%

WOOD

OPEN AIR

BRICK

METAL

Pairing and light indicators description

The outdoor intercom is fitted with a light indication behind the

name plaque, it shows:

If it is off, the unit is only powered by battery (standby mode)

If it is RED, the DOWN button (7) is depressed

If it is BLUE, the unit is powered by the adaptor durting the nigh (standy mode)

If it is RED/BLUE, the DOWN button (7) is depressed durong the night

The indoor monitor is fitted with a light indication, it shows:

If it is off, standby mode

If it is RED, the unit is charging

If it is GREEN/YELLOW, somebody is ringing

If it is BLUE, you are talking to a visitor

If it is GREEN/YELLOW, you are listening to the visitor

1. Push the monitor button (10) to turn on the screen

2. Press and hold the intercom button (8) pressed for 2 to 10

seconds and a pairing picture appears on the screen

3. Press briefly the DOWN button (7) on the outdoor intercom to turn it on

4. KEEP pressing the DOWN button (7) on the indoor intercom

5. A check appears on the screen to show that the pairing is finished.

6. If the pairing failed, a cross appears, repeat operations 2 , 3 + 4.

Doorbell volume setup:

1. Press the DOWN button (7) on the indoor intercom

2. Push the monitor button (8) to activate the screen

3. Press the Left (4) or Right (5) button to select the volume

Monitor brightness setup:

1. Press the DOWN button (7) on the indoor intercom

2. Push the monitor button (8) to activate the screen

3. Press the Up (3) or DOWN (7) button to select the brightness

Date and time setup:

1. Push the monitor button (10) to turn on the screen

2. KEEP pressing the OK/Photo (6) button for 10 seconds

in order to access the time setup

3. Press the Left (4) or Right (5) button to select an item

4. Press the Up (3) or DOWN (7) button to adjust the value

5. Press the OK/Photo (6) button to confirm and quit.

Troubleshooting:

If the doorbell doesn't ring, check the points below:

1. Used batteries in the push-button or in the doorbell.

2. Wrong battery polarity in the push-button or in the doorbell.

3. For the pluggable doorbells, make sure the wall socket is powered.

4. The pushbutton and the doorbell are not paired, see the setup guide.

5. Material between the pushbutton and the doorbell reduce the

operational range, move the doorbell closer to the pushbutton.

6. The wireless devices may be affected by external sources such as

wireless domestic alarms or electrical adapter/transformer.

These symbols indicate that this product

must not be disposed of with other

household rubbish in the EU. In order

to avoid all damage to the environment

or to human health with rogue disposal,

responsibly recycle this product in order

to encourage reuse of the material

resources. To return you used device,

please use collection and return systems,

or contact the dealer where you bought

this product. He will take the product in

order to protect the environment.

Complies to all relevant European directives.

Smartwares declares the device, model [VD38W], complies

with the requirements of the R&TTE, 1999/5/CE directive.

The compliance statement is available upon request to:

Frequency 2.4GHz

Product specificaties

Merk:	Smartwares
Categorie:	Bewakingscamera
Model:	VD38W
Soort bediening:	Knoppen
Kleur van het product:	Wit
Kleur:	Ja
Beeldschermdiagonaal:	3.5 "
Field of view (FOV) hoek:	45 °
Luidspreker:	Ja
Ingebouwde luidsprekers:	Ja
Ingebouwde microfoon:	Ja
Display technologie:	TFT
AC-adapter, uitgangsspanning:	5 V
AC-adapter, uitgangsstroom:	1 A
Maximum outdoorbereik:	175 m
Aantal displays ondersteund:	1