Smart-AVI XT-TX800 Handleiding

Smart-AVI AV extender XT-TX800

Lees hieronder de 📖 handleiding in het Nederlandse voor Smart-AVI XT-TX800 (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Notice

The information contained in this document is

subject to change without notice. Smart-AVI makes

no warranty of any kind with regard to this material,

including but not limited to, implied warranties of

merchantability and fitness for any particular

purpose.

Smart-AVI will not be liable for errors contained herein

or for incidental or consequential damages in

connection with the furnishing, performance or use

of this material.

No part of this document may be photocopied,

reproduced or translated into another language with

out prior written consent from Smart-AVI.

For the complete manual, visit www.smartavi.com.

Use CAT5 cable to broadcast high

resolution SXGA, Stereo Audio, RS232

and IR to 8 stations up to 1000ft

away.

XT-800

www.smartavi.com

User Manual

2840 N. Naomi Ave.

Burbank, California 91504

Phone: (818) 565-0011

Facsimile: (818) 565-0020

Technical Specifications

3MART!UDIO6IDEO)NTEGRATION

SNOITACIFICEPS008-TX SNOITACIFICEPS008-TX SNOITACIFICEPS008-TX SNOITACIFICEPS008-TX SNOITACIFICEPS008-TX

ataDAGV ataDAGV ataDAGV ataDAGV ataDAGV

tamroF SBVC,C/Y,VUY,BsGR,VHBGR

noituloseR 0021x0091otpU

)AGXS,AGX,AGVS,AGV

epytrotcennoC tekcos51DH

oiduA oiduA oiduA oiduA oiduA

epyTlangiS decnalabnuoeretS

rotcennoC tekcoskcajmm5.3

rewoP rewoP rewoP rewoP rewoP

stnemeriuqeR A5.@CDV5

rotcennoC )ev+retnec(kcajCDmm1.2

lacisyhP lacisyhP lacisyhP lacisyhP lacisyhP

snoisnemiD )sgephtiw1.3(mc7.2x8.11x22

thgieW sbl5.3

Sending an RS232 command to remoteSending an RS232 command to remoteSending an RS232 command to remoteSending an RS232 command to remoteSending an RS232 command to remote

monitormonitormonitormonitormonitor

In order to send a command to a remote monitor, you

will need to use The following query at 9600 baud

rate;

 After sending this query, any command sent from

the PC will go directly to monitor 1

 To send a command to monitor 2 replace "M1"

with "M2" etc...

 To send the same command to all monitors ( but

only monitor 1 will answer) Use the following

command;

<CR> = Carriage return

In Out In Out

RS232

Out 1-8

Introduction

The XT800 range of products allows the extension of

a wide range of video and audio formats, RS232, and

IR up to 8 locations using Category 5 Unshielded

Twisted Pair (UTP) cables.

With RS232 communication support, the XT800

allows users to send commands to single or multiple

devices. This allows the user to change volume,

channel or turn on/off the remote LCD TV.

Features

 Supports Dual Screens.

 Uses easy to install, inexpensive CAT-5/5e/6/7/8.

 Output reaches up to 1,000 feet (300 m).

 Resolutions up to 1900x1200.

 HDTV Compatible (720p, 1080i, 1080p)

 300 MHz Bandwidth.

 Sends high-resolution UXGA, Stereo Audio signals,

RS232 or IR from one source to 8 locations.

 Compatible with VGA, XGA, Sun, MAC and SGI

 Sync Format / Polarity Preservation.

 Compatible with Line Level Stereo Audio Signals.

 High ground loop immunity.

 Built-in power surge and transient protection.

 Designated trimmer in the remote unit to

compensate for cable length.

 Compact Metal Case Enclosure.

 External power supply.

 RS-232c communication support to single or mul

tiple displays.

 IR command to single or multiple displays.

What’s in the box?

XT800XT800XT800XT800XT800

Please check package contents before installing.

Installation Diagram

XT800 Transmitter Installation Diagram XT800 Receiver Installation Diagram

Adjusting and Tuning the SignalAdjusting and Tuning the SignalAdjusting and Tuning the SignalAdjusting and Tuning the SignalAdjusting and Tuning the Signal

In order to fine tune the signal, adjust the individual

dials one at a time starting with GREEN, then BLUE,

and lastly RED. As you turn the dials you will notice the

colors slightly change as you increase or decrease the

strength. All dials should be around the same distance.

Preparing & Connecting System CAT5 CablePreparing & Connecting System CAT5 Cable

Preparing & Connecting System CAT5 CablePreparing & Connecting System CAT5 CablePreparing & Connecting System CAT5 Cable

Following is the wiring standard for terminating CAT 5

cable using RJ-45 connector:

Pair 1 Pins 1 & 2

Pair 2 Pins 3 & 6

Pair 3 Pins 4 & 5

Pair 4 Pins 7 & 8

C o n ne c to r s :C o n ne c to r s :

C o n ne c to r s : RJ-45

C a p a c i t a n c e:C a p a c i t a n c e:

C apac i t anc e : 14 pf/ft (46.2 pf/m)

Conductor Gauge:Conductor Gauge:

Conductor Gauge: 24 AWG

I m p e d a n c e :I m p e d a n c e :

I m p e d a n c e : 100 +/- 15 ohms

4 - Pair

Connecting The TransmitterConnecting The Transmitter

Connecting The Transmitter

1. Connect the output of the computer video card to the

video input of the transmitter using the included male

to male video cable.

2. Connect the output of the computer audio card to the

audio input of the transmitter using 3.5mm audio

male to male audio cable.

3. Connect local monitor to the VGA out of the

transmitter.

4. Connect external speakers to the transmitter’s audio

out (Standard 3.5mm stereo miniplug).

5. In the back of the unit connect the CAT5 cable that

will connect to the receiver (XT800-RX).

*NOTE: You can not use RS232 and IR at the same time.

Connecting The ReceiverConnecting The ReceiverConnecting The ReceiverConnecting The ReceiverConnecting The Receiver

1. Connect CAT5 cable (coming from the transmitter) to

the back of the receiver.

2. Connect 1-4 display monitors to the VGA out

connectors on the front of the receiver.

3. Connect 1-4 sets of external speakers to the audio

output connections on the front of the unit.

(Standard 3.5mm stereo Miniplug)

tnetnoCegakcaP008TX tnetnoCegakcaP008TX tnetnoCegakcaP008TX tnetnoCegakcaP008TX tnetnoCegakcaP008TX

ytQ ytQ ytQ ytQ ytQ smetI smetI smetI smetI smetI .oNtraP .oNtraP .oNtraP .oNtraP .oNtraP

1 tinurettimsnarT008TX XT-008TX

1 ylppusrewopcdtlov5 SU-A1D5-SP

1 )tf6(elbacAGVelamotelam51DDH 60-MMAGV-CC

lanoitpO lanoitpO lanoitpO lanoitpO lanoitpO

1 tinUrevieceRORPTX XR-ORPTX

1 elbacgulpinimoeretsmm5.3oiduA 60-MMAMM-CC

1 revieceREYERI EYE-MS

1 rettimERI DEL-MS

1 elbac232SR'6 60-232SRCC

XT400

VGAOut

8lines

of CAT 5

XTP RORX

XTPR O R X

XT800

Product specificaties

Merk:	Smart-AVI
Categorie:	AV extender
Model:	XT-TX800
Kleur van het product:	Zwart
Gewicht:	1500 g
Soort:	AV-zender
LED-indicatoren:	Ja
Ondersteunde video-modi:	1080i, 1080p, 720p
Maximum resolutie:	1920 x 1200 Pixels
VGA (D-Sub)poort(en):	2
Aansluiting voor netstroomadapter:	Ja
Audio-ingangen:	1
Audio-uitgang:	1
Externe adapter:	Ja
Afmetingen (B x D x H):	220 x 118 x 27 mm
Bandbreedte:	300 MHz
RJ-45 invoer ports:	8
Operating voltage:	5 V
Maximaal bereik:	300 m
Ondersteundende kabel types:	Cat5, Cat5e, Cat6, Cat7
Aansluiting type:	HD15