Smart-AVI VCT-400 Handleiding

Smart-AVI AV extender VCT-400

Lees hieronder de 📖 handleiding in het Nederlandse voor Smart-AVI VCT-400 (2 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Notice

The information contained in this document is

subject to change without notice. Smart-AVI makes no

warranty of any kind with regard to this material, including

but not limited to, implied warranties of merchantability

and tness for any particular purpose.

Smart-AVI will not be liable for errors contained

herein or for incidental or consequential damages in

connection with the furnishing, performance or use of

this material.

No part of this document may be photocopied,

reproduced or translated into another language with

out prior written consent from Smart-AVI.

For the complete manual, visit www.smartavi.com.

Use a single CAT5 to broadcast high

resolution UXGA to 4 locations

1000ft away

VCT400

www.smartavi.com

User Manual

2840 N. Naomi Ave.,

Burbank, California 91504

Phone: (818) 565-0011

Facsimile: (818) 565-0020

Technical Specications

Transmitter and receiver

Video

Bandwidth 400MHz

Analog signal Level 1 volt

Impedance 75 ohms

Connector High density HD15

Format VGA/SVGA/XGA/UXGA/RGBH/RGsB

Sync TTL horizontal SyncRange: 15 to 130 KHz Verti-

cal Sync Range 30 to 120 Hz

Signal level OdB

Impedance 10K ohms

Connector 3.5mm jack socket

System Cable

Type Cat5 UTP EIA 568A

Connector RJ45

Power

Requirements 5V DC @500mA

Connector 5x2.1 DC Jack

Introduction

The VCT400 allows transmission of high denition

video signals over a standard CAT-5 UTP cable over

distances of up to 1000 ft.

Features

Uses easy to install, inexpensive CAT5.

Output reaches up to 1,000 feet.

Resolutions up to 1900x1200.

300 MHz Bandwidth.

Sends high-resolution VGA signals from

one source to up to 4 devices.

Compatible with VGA, XGA, Sun, MAC and SGI

signals.

Sync Format / Polarity Preservation.

High ground loop immunity.

Built-in lightning, power surge and transient

protection.

Designated trimmer in the remote unit to

compensate for cable length.

Compact Metal Case Enclosure.

Remote Units come with Buered Outputs.

External power supply.

What’s in the box?

Installation Diagram

VCT Receiver Installation Diagram

Connecting The Transmitter

1. Connect the output of the computer video card to the

video input of the transmitter using the included male

to male video cable.

2. Connect local monitor to the VGA out of the

transmitter.

3. In the back of the unit connect the CAT5 cable that

will connect to the receiver unit.

4. Connect the power supply.

*NOTE: You can not use RS232 and IR at the same time or Audio.

Connecting The Receiver

1. Connect CAT5 cable (coming from the transmitter) to

the back of the receiver.

2. Connect monitors to the VGA out connectors on the

front of the receiver.

3. Connect the power supply.

Description Part Number

4 port VCA UXGA VCA-TX400

5VDC 1A Power Supply PS-5D1A-US

VGA cable Male to Female CC-VGAMM-06

Optional Equipment

VCAT-100-RX Receiver Unit VCT-100-RX

Adjusting and Fine Tuning the Signal

Preparing & Connecting System CAT5 Cable

Following is the wiring standard for terminating CAT 5

cable using RJ-45 connector:

Pair 1 Pins 1 & 2

Pair 2 Pins 3 & 6

Pair 3 Pins 4 & 5

Pair 4 Pins 7 & 8

Connectors: RJ-45

Capacitance: 14 pf/ft (46.2 pf/m)

Conductor Gauge: 24 AWG

Impedance: 100 +/- 15 ohms

4 - Pair

In order to ne tune the signal,

adjust the individual dials

one at a time starting with

GREEN, then BLUE and lastly

RED. As you turn the dials you

will notice the colors slightly

change as you increase or

decrease the strength.

VCT Transmitter Installation Diagram

Up to 1,000 ft.

VCA-TX400

Transmitter

VCT-100-RX

Transmitter’s

Product specificaties

Merk:	Smart-AVI
Categorie:	AV extender
Model:	VCT-400
Kleur van het product:	Violet
Soort:	AV-zender
Maximum resolutie:	1920 x 1200 Pixels
VGA (D-Sub)poort(en):	1
Aansluiting voor netstroomadapter:	Ja
Externe adapter:	Ja
Bandbreedte:	300 MHz
RJ-45 invoer ports:	4
Operating voltage:	5 V
Aansluiting type:	HD15