Siemens ES326BB21E Handleiding

Siemens Fornuis ES326BB21E

Lees hieronder de 📖 handleiding in het Nederlandse voor Siemens ES326BB21E (9 pagina's) in de categorie Fornuis. Deze handleiding was nuttig voor 66 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/9

*9000568403* 9000568403 E

Ú Installation instructions

Û Instrucciones de montaje

Þ Notice de montage

ì Instruções de montagem







D E



/

9

9

99

1



Ú Installation instructions

Safety precautions

Read the appliance instructions before installing and using.

The graphics in these Assembly instructions are given as a

guide only.

The manufacturer is exempt from all liability if this manual's

requirements are not complied with.

All operations relating to installation, regulation and

conversion to other gas types must be carried out by an

authorised installation engineer, respecting all applicable

regulations, standards and the specifications of the local gas

and electricity providers.

You are recommended to contact the Technical Assistance

Service to convert to another gas type.

Before you begin, turn off the appliance's electricity and gas

supply.

This appliance has been designed for home use only, not for

commercial or professional use. This appliance cannot be

installed on yachts or in caravans. The warranty will only be valid

if the appliance is used for the purpose for which it was designed.

Before installing, check that local distribution conditions (gas

type and pressure) and the appliance's adjustment are

compatible (see table I). The appliance's adjustment conditions

are written on the label or the specifications plate.

This appliance can only be installed in a well-ventilated place in

accordance with existing regulations and ventilation

specifications. The appliance must not be connected to a

combustion product removal device.

The supply cable must be attached to the unit to prevent it from

touching hot parts of the oven or hob.

Appliances with electrical supply must be earthed.

Do not tamper with the appliance's interior. If necessary, call our

Technical Assistance Service.

Before installing

This appliance is class 3 type, according to the EN 30-1-1

regulation for gas appliances: built-in appliance.

These individual appliances can be combined with other

identical appliances and/or with conventional hobs of the same

make, using the joint accessory. See the catalogue for details.

The units next to the appliance must be made of non-flammable

materials. The laminated covering and glue for adhering it must

be heat resistant.

This appliance cannot be installed above fridges, washing

machines, dishwashers or similar.

An oven must have forced ventilation to install a hob above it.

Check the dimensions of the oven in the installation manual.

If an extractor fan is installed, you must follow the installation

manual's instructions, always keeping a minimum distance of

650 mm to the hob.

Preparation of the kitchen unit (fig. 1-2)

Make an appropriate size cut in the work surface.

If the hob is electric or mixed (gas and electricity) and there is

no oven below, place a non-flammable separator (e.g. metal or

plywood) 10 mm from the bottom of the hob. This will prevent

access to the base of the hob.If the hob is gas, it is

recommendable to place the separator at the same distance.

On wood work surfaces, varnish the cutting surfaces with a

special glue. This protects them from moisture which could

collect under the work surface.

Installation of appliance (fig. 3)

Note: Wear protective gloves to fit the hob.

The clips and adhesive seal (underside of the hob) are factory-

fitted: Do not remove these under any circumstances: The

adhesive seal prevents water seepage.

In order to fit the appliance into the kitchen unit, first place the

hob in the correct position then loosen each of the clips so that

they all turn freely (it is not necessary to completely undo them).

Insert and centre the hob.

Press the sides of the hob until it is supported around its entire

perimeter.

Turn the clips and tighten them fully. Fig. 3.

Removal of hob

Turn off the appliance's electricity and gas supply.

Unscrew the clips and proceed in the reverse order to

installation.

Gas connection (fig. 4)

The gas connection must be located in a position where the

stop tap is accessible.

The end of the inlet connection point of the gas hob has a 1/2”

thread (20.955 mm) that allows for:

■A fixed connection.

■Connection using a flexible pipe (L min. 1 m - max. 3 m).

In this case, it is necessary to insert the accessory (427950)

and the watertight seal (034308) supplied between the manifold

outlet and the gas supply. Fig. 4a.

D





Product specificaties

Merk:	Siemens
Categorie:	Fornuis
Model:	ES326BB21E
Apparaatplaatsing:	Ingebouwd
Kleur van het product:	Zwart
Gewicht:	7000 g
Breedte:	302 mm
Diepte:	520 mm
Hoogte:	45 mm
Snoerlengte:	1 m
Vermogen brander/kookzone 2:	1700 W
Vermogen brander/kookzone 1:	3000 W
Aantal branders/kookzones:	2 zone(s)
Type kookplaat:	Gaskookplaat
Type brander/kookzone 1:	Groot
Type brander/kookzone 2:	Regulier
Aantal gaspitten:	2 zone(s)
Aantal elektronische kook zones:	0 zone(s)
Normale brander/kookzone:	1700 W
Grote brander/kookzone:	3000 W
Restwarmte-indicator:	Nee
Voedingsbron brander/kookzone 1:	Gas
Voedingsbron brander/kookzone 2:	Gas
Positie brander/kookzone 1:	Midden achter
Positie brander/kookzone 2:	Midden voor
Kookzone 1 vorm:	Rond
Kookzone 2 vorm:	Rond
AC-ingangsspanning:	220 - 240 V